DIGITUS 5 Port Gigabit Switch DN-80202 Installation Guide
- June 7, 2024
- DIGITUS
Table of Contents
5 Port Gigabit Switch,
Unmanaged
Quick
Installation Guide
DN-80202
About The Guide
This guide provides instructions to install the Ethernet Switch.
Note: The model you have purchased may appear slightly different from the
illustrations shown in the document. Refer to the Product Instruction and
Technical Specification sections for detailed information about your switch,
its components, network connections, and technical specifications.
This guide mainly divides into 3 parts:
- Product introduction: functional overview and introduction of panel definitions
- Hardware installation: step by step hardware installation process
- Technical specifications
Product Introduction
The 5-Port Gigabit Switch from DIGITUS® is perfectly suited for the easy expansion of your network. Thanks to its fanless design, the switch operates completely noise-free and does not require configuration. Each port can be used as LAN or an uplink port, the cable and network speed are detected automatically. The switch also supports the energy-saving features IEEE802.3az & Full-Duplex Flow Control IEE802.3x. Real Plug and Play – Just plug in the network cable and get started.
Product Features
- Automatic MDI/MDI-X crossover for plug-and-play
- 5 port supports both 10/100/1 000 Mbps speed auto-negotiation
- 5 DC 1 A external power adapter
- Supports operating temperatures from 0 °C ~ 40 °C
Front Panel
The front panel consists of LED indications.
LED Lamp
Power: The Power LED lights up when the switch is connected to a power source.
Link/Act LED: The Link/Act LED flashes which indicate a network link through
the corresponding port. Blinking indicates that the Switch is either sending
or receiving data to the port.
Rear Panel
The rear panel view consists of a DC power connector and network ports.
Connect the power adapter output terminal to this port. Supports input voltages 5V 1A.
Hardware installation
This chapter provides unpacking and installation information for the Ethernet
switch.
Open the seal
Open the shipping carton and carefully unpack its contents. Please consult the
packing list located in the User Manual to make sure all items are present and
undamaged. If any item is missing or damaged, please contact the local
reseller for replacement.
- Switch 1 pcs
- Power adapter 1 pcs
- QIG 1 pcs
Connecting power supply
Using the AC power cord to connect to the power adapter, and then plug the
output terminal of the adapter into the DC IN socket on the back of the
switch. (The AC the power outlet should be grounded)
Switch installation
For safe switch installation and operation, it is recommended that you:
- Visually inspect the power cord to see that it is secured fully to the AC power connector.
- Make sure that there is proper heat dissipation and adequate ventilation around the switch.
- Do not place heavy objects on the switch.
Desktop Installation
When installing the switch on a desktop, the rubber feet included with the
device must be attached on the bottom at each corner of the device’s base.
Allow enough ventilation space between the device and the objects around it.
Warning: Do not turn on the power switch before power cables are
connected.
A power surge may cause damage to the Switch.
Power failure
As a precaution, the switch should be unplugged in case of power failure. When
power is resumed, plug the switch back in.
Application
- Gaming console
- VoIP Phone
- Internet
- Broadband Router
- Wireless Access Point
- Notebook
- PC
- Home Cinema
- IPTV
- IP Camera
Technical Specifications
Hardware technology
Standard| IEEE 802.3, 802.3u, 802.3x,802.3ab,802.3az
Processing type| Store & forward; wire-speed switching
MAC addresses| 2K
Memory bandwidth| 10 Gbps
Throughput
(packet per second)| 7.44 Mpps
Flow control| IEEE 802.3x flow control, back pressure flow control
Basic function| Full-duplex wire-speed forwarding
MAC Address Auto-Learning and Auto-updating
| IEEE802.3x Full-Duplex flow control IEEE802.3az Energy Efficient Ethernet
(EEE)
---|---
Forwarding rate| 10BASE-T: 14 880 pps/port
100BASE-TX: 148 800 pps/port
1 0008ASE-TX: 148 800 pps/port
Network media| 10BASE-TX: UTP category 5, Se cable (5 250 m) 100BASE-TX:
UTP category 5, Se cable (5 150 m) 1 0008ASE-TX: UTP category 5, Se cable (5
150 m)
Interface
RJ45 ports| 5 10/100/1000Mbps Auto-Negotiation R145 ports (Auto
MDI/MDIX)
LED indicators| Power, Link/Act
Power input
Power Supply| External power adapter
DC input voltage| 5V lA
DC input protection| Hot-swap protection, over-voltage protection, and
under-voltage protection
Power Consumption| 3W
Mechanical
Casing| Metal
Dimensions (W x L x H)| 92 x 69 x 25 mm
Installation| Desktop
Environment
Operating temperature| 0 °C’ 40 °C
Storage temperature| -40 °C’ 70 °C
Ambient relative humidity| 10 %” 90 % RH, non-condensing
This is a Class A product. In-home environment, this product may cause radio
interference. In this case, the user may be required to take appropriate
measures.
Hereby Assmann Electronic GmbH declares that the Declaration of Conformity is
part of the shipping content. If the Declaration of Conformity is missing, you
can request it by post under the below-mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>