allen roth 1694VA-60-241-900-UM Undermount Double Sink Instructions

welcoming

MODEL NUMBER|

DESCRIPTION

---|---
1694VA-60-241-900-UM| AR 60-IN LARSEN WHITE PAINTED OAK VANITY W/CARRARA MARBLE TOP
1694VA-60-241-901-UM| AR 60-IN LARSEN WHITE PAINTED OAK VANITY W/ENGINEERED WHITE TOP
1694VA-60-241-925-UM| AR 60-IN LARSEN WHITE PAINTED OAK VANITY W/ENGINEERED CARRARA TOP
1694VA-60-241-926-UM| AR 60-IN LARSEN WHITE PAINTED OAK VANITY W/ENGINEERED CALACATTA TOP
1694VA-60-274-900-UM| AR 60-IN LARSEN CERUSED NATURAL OAK VANITY W/CARRARA MARBLE TOP
1694VA-60-274-901-UM| AR 60-IN LARSEN CERUSED NATURAL OAK VANITY W/ENGINEERED WHITE TOP
1694VA-60-274-925-UM| AR 60-IN LARSEN CERUSED NATURAL OAK VANITY W/ENGINEERED CARRARA TOP
1694VA-60-274-926-UM| AR 60-IN LARSEN CERUSED NATURAL OAK VANITY W/ENGINEERED CALACATTA TOP

60-IN VANITY WITH TOP
MODEL #1694VA-60-241-900-UM; 1694VA-60-241-901-UM; 1694VA-60-241-925-UM; 1694VA-60-241-926-UM; 1694VA-60-274-900-UM; 1694VA-60-274-901-UM; 1694VA-60-274-925-UM; 1694VA-60-274-926-UM

ATTACH YOUR RECEIPT HERE
Serial Number__ Purchase Date__
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday.

PACKAGE CONTENTS (Undermount Sink)

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING

• There are several assembly steps, including unpacking, that require two adults.

CAUTION

• Follow these instructions closely, take your time, and use care while assembling this vanity.
  KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PREPARATION

Before beginning the assembly of the product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Installation Time: 45 minutes (24 hours for silicone caulk to dry).
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with a drill bit, measuring tape, level

INSTALLATION INSTRUCTIONS (Undermount Sink)

1. To remove drawers preassembled in vanity (A), fully extend drawers. Locate plastic levers on metal glide tracks on the left and right sides of the drawer box.
   To disengage drawer box from glides, push on plastic levers. Then, gently lift the drawer up to remove it from the vanity (A).
   Note: Clean area where the vanity (A) will be permanently located prior to beginning installation, ensuring the vanity (A) will not interfere with any water supply and drain lines once mounted.

2. With two people, carefully place vanity (A) against the wall in its final location. While holding the vanity base firmly against the wall, use the pre-assembled levelers on the bottom of each leg of the vanity (A) to level the item. Twisting the levelers counterclockwise will raise the height of the vanity (A), and twisting them clockwise will lower the vanity.
   Once the vanity is in place, against the wall, and level from front to back and side to side, drill a hole through the vanity mounting area and into the wall studs (as illustrated in diagram 2). Using appropriate mounting hardware (not included), secure the vanity (A) to a wall stud. If possible, secure the vanity (A) to two wall studs for increased stability.
   WARNING
   Vanity (A) MUST be secured to the wall.

3. Take out the top (B) and backsplash (C) according to the steps indicated by the drawings on the right, and place them face down onto a scratch-free surface such as a foam sheet that came in the packaging.
   

4. Apply silicone caulk (not included) to the top edge of the sink (D). With the help of another adult, lower the sink onto the backside of the stone top.
   
   Make sure the sink overflow hole is facing the front of the stone top.
   Be sure to align the sink well with the stone top cut out allowing for equal stone overhang on the front,  back, and sides of the ceramic sink (D). Repeat for the remaining sink.
   Note: To install the sink onto the top correctly, ensure that the two “BACK” stamps on the sink and the top are aligned on the same sides. Use the guidelines marked on the sink and bottom side of the stone top to assist with sink location.

5. Screw bolts (EE) into the threaded holes of stone top (B).
   Hardware Used

   ---

EE| Bolt|

1. | x 8  

---|---|---|---
6. Lower the sink brackets (FF) over the bolts (EE) and allow them to rest on the sink lip. Adjust the location of the bracket to firmly grasp the sink lip. Lower lock washers (HH) over bolts (EE) and secure with nuts (GG).  Hand tightens nuts (GG) with an included wrench (II). DO NOT OVERTIGHTEN! Repeat for the remaining sink. Tip: Check that the sink placement is well-centered front to back and side to side of the stone top cut out before allowing the silicone caulk to dry. If the sink is not centered well unscrew sink clamps, re-adjust the sink position, and re-tighten the sink brackets.
Hardware Used**
Note:** At this stage, it may be easier to install the faucet and drain kit (not included) to top (B) per the manufacturer’s instructions, before moving on to Step 7.

7. Apply stain-free silicone caulk (not included) to the top edge of vanity (A). With the help of another adult,  gently lower the top (B) onto the vanity (A). Wipe away any excess caulk with a soft cloth, and wait approximately 24 hours for it to dry.
   

8. Apply silicone caulk (not included) to unpolished side and bottom of backsplash (C). Position backsplash  (C) on top (B) and against the wall. Clean any excess caulk before allowing it to dry.
   

9. To reinstall drawers into a vanity (A), fully extend metal glide tracks. Gently lower and slide drawer box into rear glide catch. Next lower drawer box down to completely rest on extended glides. Then, push plastic levers to lock the drawer box in place. Repeat for remaining drawers.
   Note: To adjust the drawer box height, spin the adjustment wheel to the left to raise the drawer box or spin the adjustment wheel to the right to lower the drawer box. You can adjust the left and right-side glide heights independently in order to find the drawer’s best alignment position.
   CAUTION
   DO NOT force drawer or damage to glide may occur. If the drawer does not slide in with ease, remove it and try again from the start. Assembly is now complete. Install desired faucet and drain assemblies (neither included) per the manufacturers’ instructions to complete the installation.

CARE AND MAINTENANCE

• Dust the vanity regularly with a soft, non-lint-producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local supplier.
• Tips for using a touch-up pen (AA): For scratches, stroke in direction of scratch; for worn areas, stroke in direction of the wood grain. Rub off excess colorant promptly with a soft cloth.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble, engineered stone). Stone tops will vary from product to product. Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster, or similar item to protect the surface if placing any soap or fragranced products on the stone. If soap or fragranced products come in contact with the stone top, rinse the surface with water and dry using a soft non-abrasive cloth.
• WARNING: Must use cleaning agents safe for stone. Check your cleaning agents’ use restrictions before using on any stone. Damage to the stone may result. Vanity Manufacturer is not responsible for damage caused by improper cleaning agents or soaps used. Warranty will not cover damage caused by the use of improper soaps or cleaning agents.
• DO NOT use products to clean the stone top that contains acetone, lemon, vinegar or other acids as these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home store.  Follow the manufacturer’s directions on how to apply.

WARRANTY

The manufacturer warrants this item against defects in materials and workmanship for a period of one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser. This warranty does not apply to any damage on the product by accident, misuse, or modified, improper installation, or by affixing accessories not produced by the manufacturer. The manufacturer will not be held liable for damages caused by cleaners or soaps that etch or stain the stone top. The manufacturer is not accountable whatsoever for product installation during the warranty period. There is no further expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

REPLACEMENT PARTS LIST FOR 1694VA-60-241-UM (Undermount Sink)

For replacement parts, call our customer service department at 866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday.

B

| Complete Set 60″ Carrara Marble Top| 4550VT-60-900
Complete Set 60″ Engineered White Top| 4550VT-60-901
Complete Set 60″ Engineered Carrara Top| 4550VT-60-925
Complete Set 60″ Engineered Calacatta Top| 4550VT-60-926

C

| 60″ Carrara Marble Backsplash| PUBS-25-900-60
60″ Engineered White Backsplash| PUBS-25-901-60
60″ Engineered Carrara Backsplash| PUBS-25-925-60
60″ Engineered Calacatta Backsplash| PUBS-25-926-60
D| Sink| PU17-18X14-SQUARE
E| Drawer Front| 1694VA-60-241-DRAWER FRONT
AA| Touch-up pen| OF-0010
BB| Pull (with screw)| 1694VA-MB PULL
CC| Leveler| T-1007
DD| Drawer Glide Set| PUDTC-14X3-HANDLE
EE| Bolt|

GTC-SINK CLIPS

FF| Sink Bracket
GG| Nut
HH| Lock Washer
II| Wrench

REPLACEMENT PARTS LIST FOR 1694VA-60-274-UM (Undermount Sink)
For replacement parts, call our customer service department at 866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday.

PART| DESCRIPTION|

PART#

---|---|---
B| Complete Set 60″ Carrara Marble Top| 4550VT-60-900
Complete Set 60″ Engineered White Top| 4550VT-60-901
Complete Set 60″ Engineered Carrara Top| 4550VT-60-925
Complete Set 60″ Engineered Calacatta Top| 4550VT-60-926
C| 60″ Carrara Marble Backsplash| PUBS-25-900-60
60″ Engineered White Backsplash| PUBS-25-901-60
60″ Engineered Carrara Backsplash| PUBS-25-925-60
60″ Engineered Calacatta Backsplash| PUBS-25-926-60
D| Sink| PU17-18X14-SQUARE
E| Drawer Front| 1694VA-60-274-DRAWER FRONT
AA| Touch-up pen| M-3008
BB| Pull (with screw)| 1694VA-MB PULL
CC| Leveler| T-1007
DD| Drawer Glide Set| PUDTC-14X3-HANDLE
EE| Bolt| GTC-SINK CLIPS
FF| Sink Bracket
GG| Nut
HH| Lock Washer
II| Wrench

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>