GEBERIT SIGMA10 Dual Flush Plate User Manual
- October 30, 2023
- GEBERIT
Table of Contents
GEBERIT SIGMA10
OPERATION MANUAL
Safety
About this document
This document is intended for operators and users of the Geberit WC flush control with electronic flush actuation, mains or battery operation, Sigma10 actuator plate.
This document applies to the model of this WC flush control with Bluetooth® interface. The specification plate for this WC flush control is labelled with ‘BAWC-04-A’ or ‘BAWC-04-B’ and the Geberit Connect logo.
Intended use
The Geberit WC flush control with electronic flush actuation, mains or battery operation, Sigma10 actuator plate, is intended for flush actuation with Geberit Sigma concealed cisterns.
Safety notes
- Operation, care and maintenance work may only be performed by the operator or user as described in this operation manual.
- Do not modify the product or add any additional modules.
- If there is any indication of damage or defects, never attempt a repair yourself.
- Repairs may only be carried out by a skilled person using original spare parts and accessories.
Overview of the alert levels and symbols in these instructions
Alert levels and symbols
ATTENTION
Indicates a hazard which, if not avoided, can lead to material damage.
Refers to important information.
Product description
Technical data
| Mains operation| Battery operation1)
---|---|---
Nominal voltage| 85–240 V AC| –
Mains frequency| 50–60 Hz| –
Battery type| –| LR20
Operating voltage| 12 V DC| 3 V DC
Protection degree| IP45| IP45
Detection time, factory setting| 7 s| 7 s
Detection time, adjustment range| 1–60 s| 1–60 s
Interval flush time, factory setting| 5 s| 5 s
Interval flush time, adjustment range| 1–200 s| 1–200 s
Interval flush, factory setting| 24 h| 24 h
Interval flush, adjustment range| 1–168 h| 1–168 h
Wireless technology| Bluetooth® Low Energy2)
Frequency range| 2400–2483.5 MHz
Maximum output power| 4 dBm
- Battery service life: approx. 2 years
- The Bluetooth® brand and its logos are the property of Bluetooth SIG, Inc. and are used under licence by Geberit.
Simplified EU declaration of conformity
Geberit International AG hereby declares that the radio equipment type of the Geberit WC flush control with electronic flush actuation, mains or battery operation, Sigma10 actuator plate, is compliant with EU Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following Internet address: https://doc.geberit.com/970890000.pdf.
Simplified UK declaration of conformity
Geberit International AG hereby declares that the radio equipment type of the Geberit WC flush control with electronic flush actuation, mains or battery operation, Sigma10 actuator plate, is compliant with the Radio Equipment Regulations 2017.
The full text of the UK declaration of conformity is available at the following Internet address: https://doc.geberit.com/970891000.pdf
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Operation
Geberit Apps
Various Geberit apps are available for operation, settings and maintenance. The apps communicate with the device via a Bluetooth® interface.
The Geberit apps are available free of charge for Android and iOS smartphones in the respective App Stores.
Establish connection with device
- Scan the QR code and follow the instructions on the landing page.
Geberit Apps
Actuate manual flush
A manual flush is actuated by holding your hand in front of the infrared sensor.
- Hold your hand approx. 15 cm in front of the actuator plate. There is no need to touch the actuator plate.
Place your hand in the detection range for approx. 0.5–1 second for a full flush and for approx.
1–2 seconds for a partial flush.
For testing purposes, a flush can also be actuated with a Geberit app.
Actuate automatic flush
An automatic flush is actuated by stepping away from the WC.
- Leave the user detection range.
The automatic flush actuation is activated ex works. It can be deactivated at any time with a Geberit app.
Troubleshooting
| Malfunction | Cause | Rectification |
|---|---|---|
| Incorrect flushes (too soon, too late, unwanted) | Sensor window dirty or wet |
- Clean or dry the actuator plate.
Sensor window scratched|
- Contact a skilled person.
Water is running continuously into the ceramic pan.| Software fault|
- Interrupt the power supply (mains fuse) for 10 seconds.
Technical fault|
- Contact a skilled person.
The ceramic pan is not being flushed out properly.| Flush volumes set incorrectly|
- Contact a skilled person.
Ceramic pan is blocked with limescale|
- Descale the ceramic pan.
Flush cannot be actuated.| Power failure|
- Check the power supply (mains fuse).
Flush cannot be actuated.
The LED in the sensor window flashes when a user is in the user detection
range.| Battery capacity low1)|
- Replace the batteries.
Flush cannot be actuated.
The LED in the sensor window lights up when a user is in the user detection
range.| Batteries flat1)|
- Replace the batteries.
1) The state of battery charge can be checked using a Geberit app.
Maintenance
Maintenance regulations
For Geberit WC flush controls with battery operation, the batteries must be replaced after approx. 2 years.
Replace the batteries
Prerequisite
– 2 replacement batteries (type 1.5 V mono/D/LR20/AM-1, recommendation: Varta
Industrial or Panasonic Powerline) are available.
– WC lid is closed.
Loosen any screws that may be present on both sides of the actuator plate.
1 Demount the actuator plate.
2 Disconnect the power supply cable from the flush control.
3 Remove the battery compartment cover.
4 Take the batteries out and dispose of them appropriately.
5 Insert new batteries.
6 Mount the battery compartment cover.
7 Reconnect the power supply cable to the control.
Indicator light lights up.
8 Mount the actuator plate.
If necessary, screw in the screws on both sides of the actuator plate.
Care and cleaning
ATTENTION
Surface damage caused by aggressive and scouring cleaning agents
-
Never use cleaning agents that contain chlorine or which are acidic, abrasive or corrosive.
-
-
Geberit recommends the Geberit AquaClean cleaning set (art. no. 242.547.00.1).
To clean the actuator plate, the flush actuation can be suppressed for a few minutes using a Geberit app.
1 Clean the surfaces with a soft cloth and a mild liquid cleaning agent.
2 Dry the surfaces with a soft cloth.
Disposal
Constituents
This product meets the requirements of Directive 2011/65/EU (RoHS) (restriction of the use of certain hazardous substances in electrical and electronic equipment).
Disposal of waste electrical and electronic equipment
The symbol of the crossed-out wheeled bin means that waste electrical and electronic equipment (WEEE) must be disposed of separately and not with other non-recyclable waste. End users are legally obliged to return old equipment to public waste disposal authorities, distributors, or Geberit for proper disposal. Many distributors of electrical and electronic equipment are obliged to take back WEEE free of charge. Contact the responsible sales or service company to return the WEEE to Geberit.
Used batteries and accumulators that are not enclosed within the old equipment, as well as lamps that can be removed from the old equipment in a non-destructive manner, must be separated from the old equipment before being handed over to a disposal point.
If personal data is stored on the old equipment, end users themselves are responsible for deleting it before handing it over to a disposal point.
Geberit International AG
Schachenstrasse 77, CH-8645 Jona
documentation@geberit.com
www.geberit.com
9729387019 © 02-2022
970.766.00.0(00)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>