INKEE B094FF9PCQ Falcon Handheld 3-Axis Action Camera Gimbal Stabilizer User Guide
- June 6, 2024
- INKEE
Table of Contents
Falcon Quick Start Guide
V1.2
2021.01
Introduction
Falcon is a hand-held stabilizer specially designed for cameras, which
supports most of the Action Cameras on the existing market, Through the three-
axis motion compensation to stabilize the Action Camera to get a stable effect.
Product Contents
Falcon diagram
| 
---|---
*Camera not included.
Product Usage
Charging
Use TYPE-C cable to charge. The status indicator is red when charging while
the green light is always on when fully charge.
Note :
- Make sure to fully charge the stabilizer when used for the first time.
- Please charge the stabilizer immediately if the power is too low and the red-light flashes slowly.
- Turn off the power if not in use.
Installation of Action Camera
Take GoPro HERO9 as an example:
- Pull apart the bottom mounting buckle of the action camera and install it on the stabilizer.
- 2)Insert the screw into the hole corresponding to the stabilizer and then tighten the screw.
Power Button
- Under the condition of power on or off, Long press two seconds the power button to turn on or turn off the gimbal.
- Under the condition of power on or off, single press the power button to display the power of the stabilizer.
- In the boot state, double press the power button into standby mode, and then single press any button to restore the working state of the stabilizer.
- In the boot state, continuously and quickly press eight times to clear the remote-control pairing. Too slow will trigger standby.
Note:
The Action Camera can only be turned on after it is firmly installed.
Shutter Button
Shooting Button: Single press to shoot
REC Button: Single press to start recording or stop.
Time-lapse Button: Single press the button to start time-lapse shooting or
stop.
Function Operation
Mode Function
-
Following Mode
-
Lock Mode
Pan and Tilt
Locked Mode Long press trigger button
The red circle indicates that the motor follows the movement of the handle to change the angle, while the gray circle indicates that the motor locks the angle and does not follow the movement of the handle. -
Vertical shooting Mode and Flashlight Mode
Double click to enter vertical shooting mode, double click again to enter Flashlight Mode. Single-click to exit to HL mode.
Mode
|
Description
---|---
Pan Following Mode (default)| The tilt axis and roll axis keep the same
direction, and the lens rotates with the direction of the handle.
Pan and Tilt Following Mode| The roll axis keeps the same direction, and the
lens rotates with the direction of the handle.
Lock Mode| The lens keeps the same direction.
Reset| Return to Pan Following Mode, tilt axis, roll axis, and pan axis return
to a horizontal state.
Trigger-Lock| Pull the camera to the specified angle of pan axis and tilt axis
for half a second to lock the current angle.
Horizontal/Vertical Shooting| Help the camera to shoot horizontally or
vertically.
Trigger Button Operation
| Joystick Operation | Description |
|---|---|
| Push upwards /downwards | The tilt axis rotates up or down |
| Push left/right | Pan axis rotates left or right. |
Mode Switch Button
-
Illustration
① Single click to switch PF-HL-FPV mode.
② Double click to enter vertical shooting mode, double click again to enter Flashlight Mode.
Single-click to exit to HL mode.
③ Long press the Trigger Button to enter GL Mode(Lock Mode), release to back to previous
mode(GL Mode works only under PF or HL Mode). -
The current model of the stabilizer can be identified by the status of the indicator light.
Trigger Button Operation
Trigger Button Operation
|
Description
---|---
Press and hold| Into GL mode (release will back to the previous model)
Double press| Reset (Tilt axis and roll axis)
Three-times press| Pan axis rotate 180. Tilt axis and roll axis back to the
original position.
Manual Lock
Grasp the camera and pull it to the specified angle in the tilt direction,
stay for half a second and then lock the current angle.
Indicator Light Status
Indicator Light Status
|
Description
---|---
Blue LED Light| Power off and standby mode shows the current power from left:
0-25%, 25-50%, 50-75%, and 75-100%.
After power on the stabilizer, it represents the mode status from left to
right: Following mode (PF), Lock mode (HL), FPV mode, Flashlight mode (FL);
under GL mode all LED lights are on.
Green LED Light| Display the Bluetooth connection status. It is always on when
the Bluetooth is connected while it is always off when no connection. After
pairing is cleared, the light will flash slowly during the Bluetooth scanning,
if there is connected then always on if not then off the light.
Red LED Light| Display the current upgrade status. The red light flashes
rapidly during the upgrade, and it will turn off after three seconds when the
upgrade is completed. When the power is lowered than 10% the red-light flashes
slowly, it can’t upgrade or upgrade fails then the red light will always be
on.
Disclaimer
Warning
The contents mentioned in this article are related to your safety, legal
rights, and responsibilities. Please read them carefully and set up and use
this product correctly according to the instructions. If you do not follow the
instructions and warnings in this article, it may cause harm to you and the
people around you and damage the product or the products around you. Any
illegal use by any user is prohibited. The user will be responsible for all
actions of purchasing and using the product. For this product, the company
does not bear all the risks and responsibilities (including direct, indirect,
or third-party losses) of the end customers during the debugging and use of
this product.
Our company will not provide any service for any products obtained from
abnormal channels or for unknown purposes.
Note:
- Ensure that the motor rotation is not blocked by an external force during and after the stabilizer is powered on.
- Make sure that the stabilizer is not exposed to water or other liquids.
- Do not disassemble the whole stabilizer. If it is disassembled carelessly and causes abnormal operation, please send it back for re-debugging. All the expenses arising therefrom shall be borne by the customer.
- Long-time continuous operation may cause the surface temperature of the motor to rise, please operate with caution.
- It is strictly forbidden to fall or collide. Falling or colliding the stabilizer may damage it and cause abnormal operation. In case of abnormal work caused by falling or collision, please contact the after-sales department in time.
Storage and Maintenance
- Please keep this product out of the reach of children and pets.
- It is forbidden to place the product near the heat source (furnace or heater, etc.) and in the car in hot weather.
- Please store in a dry environment.
- Do not overcharge or over-discharge the battery, otherwise, it will cause damage to the cell.
- Do not use this product in a too high or too low-temperature environment.
Product Parameter
Product Dimension:| 236mm×111mm×37mm (Storage status)
104mm×207mm×92mm (Working condition )
---|---
Weight:| 300g（battery included）
Max. Payload:| 135g
Tilt Movement Angle:| 310°
Roll Movement Angle:| 180°
Pan Movement Angle:| 360°
Standby Time:| Laboratory stationary placement test results are 9 hours
Adaptive Reference Model:| Gopro9/8/7/6/5and other action cameras of similar
shape and size
Shenzhen Yingzhiqi Technology Co., Ltd
Address: 18A, Ruijun Business Building, No.108, Central Road, Xinqiao Street,
Baoan District, Shenzhen,
Guangdong Province
Tel：+86 40096 80096
Website：www.in-kee.com
http://weixin.qq.com/r/WEWIkALEpF-brUbz9xBK
The latest version of the User Manual is available on the Official Website:
http://www.in-kee.com/Falcon
This manual is subject to update without prior notice. If you have any
questions or suggestions about the manual, please contact
us at the following email address:
info@in-kee.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>