INKEE IRONBEE-2 Bluetooth Shooting Grip User Guide
- June 5, 2024
- INKEE
Table of Contents
- INKEE IRONBEE-2 Bluetooth Shooting Grip
- Product Description
- Instruction for use
- Indicator light description
- How to connect with a GoPro?
- Use with a camera
- Installation
- Charging Method of Remote Controller
- How to use the tripod?
- Product Parameter
- Camera Compatible List
- DISCLAIMER
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INKEE IRONBEE-2 Bluetooth Shooting Grip
Product Description
Instruction for use
- Power Button: Long press for 1 second to turn on, long press for 1 second to turn off.
- Without pairing: No connection for 10 minutes after power-on, the tripod will automatically sleep.
- Sleep Mode: Automatically sleep after 30 minutes of no operation after connection.
- Disconnection: The green light flashes once a second.
- Clear the pairing: Long press the shutter and Record buttons until the red-light blinks and turns off.
- Shutter Button: Long press to focus, release to end focusing and start taking photo.
- Recording: Recording is performed after the recording button is released (for beingcompatible with CZ010—recording button and the power button).
- GoPro Connection: When GoPro is connected, the record button(K4) is used as a switch button and the Shutter button (K2) as the execution button.
Indicator light description
- Green Light: After power-on there is no connection, and it flashes slowly; there is a connection, it is always on, and when it is fully charged, it is always on.
- Red light: when the battery is lower than 10%, it flashes slowly; when clear the pairing it flashes quickly; during charging it is always on. The red-light priority is higher than the green light, when the red light is activated, the green light is off.
How to connect with a GoPro?
GoPro Bluetooth Connection Take GoPro hero10 as an example:
- Long press the power button and switch button of the selfie stick, until the flash red light turn to green.
- Power on the GoPro hero 10, pull down the selection box from the top, and click “connect”.
- Click on “connect to new device”. ④ Click on “GoPro App”.
If the above operation fails to connect to the device, please clear the pairing of the selfie and follow the steps below, and then repeat the steps above again.
- Pull down the selection box from the top, click “connect”.
- Click “reset the connection”.
- Click “reset”.
Mounting a camera
- Open the bottom mounting buckle of the action camera and install it on the selfie.
- Insert the screw into the corresponding hole of the selfie, and then tighten the screw.
If the installed camera is GoPro hero 8, GoPro hero 9 or GoPro hero 10, it may cause the camera lock to be vacant, please adjust the position of the camera .
Use with a camera
Camera Bluetooth Connection
SONY camera with built-in Bluetooth
- Confirm that the remote-control switch button is at ON position.
- Long press the power button and switch button of the selfie stick,until the flash red light turn to the green.
- Select camera Bluetooth settings—turn on Bluetooth—select pair the camera with the Bluetooth remote control.
CANON camera
- Confirm that the remote control switch button is at ON position.
- Long press the power button and switch button of the Selfie, the red light flashes to the green light.
- Set the camera’s drive mode to
or <Selfie: 10 seconds/remote control>;Select camera Bluetooth settings-turn on Bluetooth-select camera and Bluetooth.
Installation
- Attach the quarter adapter to the Selfie.
- Then insert the screw into the corresponding hole of the Selfie and tighten the screw.
- Insert a quarter screw into the screw port of the camera and then tighten the screw.
Charging Method of Remote Controller
Connect to Type-C interface for charging. The red indicator light will be on during the charging process; After charging is completed, the red light automatically goes out.
How to use the tripod?
Open the tripod stand on the bottom, push the lever upwards, unfold the lever and then place the tripod on a flat surface.
Product Parameter
Product Specifications: As shown in the picture above (manual measurement will have errors, subject to the actual product)
Product Name:| IRONBEE-2 Remote control extension Rod
Product Material:| Aluminum alloy +ABS
Charging Method:| 5V1A
Charging Voltage and Current :| 5V1A
Bluetooth Version:| Bluetooth 5.0
Battery Capacity :| 200mAh
Product payload :| 200g
Battery Life :| 100 hours in the laboratory under static test results
Product Weight :| 113.4g (battery included, tripod not included)
Remote Control Distance :| Within 10m
Camera Compatible List
Canon
Camera Model | Photo | Video | Focus |
---|---|---|---|
EOS M50 | √ | √ | √ |
EOS M6 Mark II | √ | √ | √ |
EOS M50 Mark II | √ | √ | √ |
EOS M200 | √ | √ | √ |
PowerShot G5 X Mark II | √ | √ | √ |
PowerShot G7 X Mark III | √ | √ | √ |
EOS R | √ | √ | √ |
EOS R5 | √ | √ | √ |
EOS R6 | √ | √ | √ |
Notes:
- “√” means that this function can be realized after the remote control and the camera are connected.
- Canon cameras need to be equipped with a power zoom lens to be able to zoom.
Cony
Camera Mode | Photo | Video | Focus |
---|---|---|---|
Alpha 7C | √ | √ | √ |
Alpha 7R IV | √ | √ | √ |
Alpha 7R III | √ | √ | √ |
Alpha 9 | √ | √ | √ |
Alpha 6600 | √ | √ | √ |
Alpha 6100 | √ | √ | √ |
Alpha 7 III | √ | √ | √ |
Alpha 9 II | √ | √ | √ |
Alpha 6400 | √ | √ | √ |
ZV-1 | √ | √ | √ |
DSC-RX0M2 | √ | √ | √ |
DSC-RX100M7 | √ | √ | √ |
Alpha 7S III | √ | √ | √ |
DISCLAIMER
Caution
The content mentioned in this article is related to your safety, legal
rights and responsibilities, please be sure to read it carefully, and Follow
the instructions to set up and use the product correctly. Failure to follow
the instructions and warnings in this article may cause you and others around
you To damage or damage this product or surrounding products. Any illegal use
by any user is prohibited. The user will buy and use the product Responsible
for all actions. For this product, the company does not assume the risk of all
commissioning and use of this product by the end customer And liability
(including direct and indirect or third-party losses). Our company for any
obtained from abnormal channels or unknown uses No service will be provided
for the products.
Shenzhen Yingzhiqi Technology Co., Ltd.
- Add: Floor5, Building 2 (W), Xixiangle Zhujiao Hongye Industrial Zone, Baoan District, Shenzhen, Guangdong China.
- Phone:+86 40096 80096
- Website:www.in-kee.com
- You can check the latest version of the “User Manual” on the official website. https://www.in-kee.com/en/ironbee-2-user-manual/
This manual is subject to update without notice.
If you have any questions or suggestions about this manual, please contact us
at the following email address: info@in-kee.com
Copyright © 2021 IRONBEE-2 All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>