Thomann Swissonic Quadphone User Guide
- June 6, 2024
- Thomann
Table of Contents
Swissonic
Quadphone
Quick Start Guide
This quick start guide contains important information on the safe operation of
the product. Read and follow the safety advice and instructions given. Retain
the manual for future reference. If you pass the product on to others please
include this manual.
Safety instructions
Intended use
This product is meant to be used to amplify analog audio signals for playback
with headphones. Any other use or use under other operating conditions is
considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that
children do not detach any small parts from the product. They could swallow
the pieces and choke! Never let children unattended use electrical devices
Where to use the product
Never use the product
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- at locations where the unit can become wet
Possible hearing damage
When headphones are connected, the unit can produce a volume that may cause
temporary or permanent hearing impairment. Do not operate the device
continuously at a high volume. Turn down the volume immediately if background
noise or hearing failure should occur.
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Operating elements
1. Volume control for outputs 1 – 4.
2. Outputs 1 – 4, 1/4″ jacks.
3. Power-on indicator.
4. Power supply port.| 5. Toggle switch for stereo or mono operation.
6. RCA inputs for line-level signals.
7. 1/4″ jack for line-level signals.
---|---
Using the product
- Connect the analog signal source whose line-level signals you want to play via headphones using an RCA cable to the INPUT socket pair (y) or to the 1/4″ jack INPUT (u).
- Connect up to four headphones to the unit via the 1/4″ phone jacks (w).
- Connect the power adapter cable to the 12 – 16 V jack (r) and plug the power adapter into a properly wired electrical outlet. The power-on light comes on.
- Adjust the volume of each headphone output with the controls (q) as desired.
- For stereo signal playback, set the stereo/mono switch (t) to the stereo position, otherwise to the mono position.
- To turn off the device, unplug the power adapter from the wall outlet.
Technical specifications
| Input impedance | ca. 900 g |
|---|---|
| Max. input level | +22 dB |
| Output impedance | 10 Ω per channel |
| Max. gain | 19 dB |
| Signal-to-noise ratio | >98 dB |
| Power supply | external power adapter, 100 – 240 V 50/60 Hz |
| Operating voltage | 12 V , 500 mA, center positive |
| Dimensions (W × H × D) | 94 mm × 45 mm × 80 mm |
| Weight | ca. 900 g |
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in our country. If in doubt, consult your local waste disposal facility.
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • info@thomann.de DocID: 442056_11.11.2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>