PYLE UHF Wireless Microphone System PDWMU114 User Manual

: June 6, 2024
: Pyle

Table of Contents

PYLE UHF Wireless Microphone System User Manual
Documents / Resources
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PYLE UHF Wireless Microphone System User Manual

UHF Wireless Microphone System

Please read this manual carefully before using and strictly operate and store in accordance with the instructions. Please save it for your future reference.

The wireless system is reliable in performance, portable and easy to operate, and is suitable for use at home, school, training room and outdoor performance. The wireless system adopts advanced intelligent digital technology and high integrated circuit design, which has the advantages of strong stability, intelligence and high efficiency.

FEATURES

UHF frequency for stronger anti-interference ability and stable transmission distance.
The transmitter has a frequency modulation function to meet the simultaneous use of multiple frequencies.
The receiver adopts automatic frequency lock design, which makes operation simpler and smarter.
Mini receiver design with 6.35mm standard audio plug, plug and play.
The receiver has a rechargeable function, circuit protection technology and a detachable large-capacity lithium battery. It can also be connected to a power bank for long-term offline use.
Easy to operate, easy to use and have a good sense of experience.

RECEIVER FUNCTION DESCRIPTION

6.35mm audio plug
Power switch
Power indicator, charging indicator
DC 5V charging port
RF signal indicator
Antenna
18650 lithium battery negative electrode*
18650 lithium battery compartment
18650 lithium battery positive electrode*

Note: Be sure to confirm the positive/negative battery before installing it to avoid damage to the receiver! Please fully charge the lithium battery before using it.

TRANSMITTER FUNCTION DESCRIPTION

Handheld Microphone

Handheld Microphone

Microphone head
LED display
Microphone switch
CH button
Battery compartment
Transmitter antenna
Tail cover

BODYPACK TRANSMITTER

Antenna
Volume Adjust and ON/OFF button
Microphone Connector
CH Button DOWN
CH Button UP
LED Display
Battery compartment
Double AA batteries (AA 1.5VX2)
Headset microphone
(Lavalier microphone)

OPERATION

Tips:

Under normal circumstances, the product has been completed at the factory, and can be used normally after opening the box, no need to adjust the frequency.

If you need to adjust the frequency, please follow the steps below.

Note: Before operating, make sure the transmitter and receiver are both off.

The operation sequence of handheld microphone:

Operate the transmitter
Open the receivers
Confirm at the transmitter
Press and hold the power button and CH button of the transmitter at the same time until the LED display flashes then release the button.
Turn ON the receiver power button, please pay attention to the RF signal indicator of receiver. Under normal circumstances, the receiver RF signal indicator flashes continuously for 4 times and then goes out. (In this case, the receiver and the transmitter are connected successfully.)
Short press the transmitter CH button to confirm the connection between the transmitter and the receiver. At this time, the transmitter display stops flashing, and the receiver RF signal indicator is always ON, indicating that the receiver and the transmitter are connected successfully.

Note:

If it can’t be connected, please repeat the above operation.

(The transmitter must be operated before the receiver is turned ON.)

When the same frequency interference occurs, please short press the transmitter CH button. At this time, the transmitter will change the frequency to avoid frequency interference.

Bodypack Transmitter Operation Sequence

The transmitter and receiver are both off.
Press and hold ” ” CH button and turn ON the power switch button to “ ON ” at the same time until the LED display flashes for 4 seconds, then release the ” ” CH button.
Turn ON the receiver power button, pay attention to the RF signal indicator of receiver. Under normal circumstances, the receiver RF signal indicator flashes continuously for 4 times and then goes out. (In this case, the receiver and the transmitter are connected successfully)
Short press the transmitter ” ” CH button to confirm the connection between the transmitter and the receiver. At this time, the transmitter display stops flashing, and the receiver RF signal indicator is always ON, indicating that the receiver and the transmitter are connected successfully.