LIKE SPORTING HITWAY J5 Electric Bike Instruction Manual

: June 4, 2024
: LIKE SPORTING

Table of Contents

LIKE SPORTING HITWAY J5 Electric Bike
Overview
Function
Remove the battery
Product Parameters
Product Description and Characteristics
Installation
System usage
Other interfaces
Precautions
Disclaimer
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LIKE SPORTING HITWAY J5 Electric Bike

Overview

Gear Shifter
Brake lever
Display
Handle stem
Front light
Rim
Tyre
Fork
Wheel reflector
V-brake
Fender
Chainwheel
Pedals
Chain
Lithium battery
Rear derailleur
Freewheel
Motor
Rear light
Rear carrier
Seat post quick release
Seat post
Saddle
Battery indicator button
Battery On/Off button
Battery charging port
Battery keyhole

Function

Charging: Open the plastic cover on the right side of the frame and connect the charger to start charging. When the battery is full and the charger indicator turns from red to yellow-green, it means it is fully charged.
Turn on: Refer to Figure 2. Long press the “i” key to turn on/off the power.
Power display: After power on, the dashboard will display the power on the bright screen. The power is displayed in four grids, corresponding to high, medium, and low power.
Front light: Refer to Figure 2, long press the “+” key to turn on/off the front light.
Riding mode:
Power-assisted riding: When the power is turned on, step on the sprocket of the vehicle, and the power will automatically start assisting when the vehicle reaches a certain speed. If you don’t need electric assist, you can turn off the power or battery;
Electric riding: When the power is turned on, move the throttle paddle down and the motor will rotate to drive the vehicle forward.

Note: Do not use excessive force when turning the throttle paddle to avoid damaging it.

“ – ” key
“ i ” key
“ + ” key
Bell
Speed stage indication window
Speed downshift paddle
“+” Upshift button
Throttle paddle

Remove the battery

Insert the key into the battery lockhole, rotate it to the left to unlock it, and then pull the battery out.
Battery On/Off button
Power display lamp
Battery charging port
Battery capacity button
Press this button on the battery box to display the battery capacity after the green light is lightened. More green lights lightened shows more battery capacity.
Note: The pedals are not installed at the factory and can be installed by using the special wrench coming with the vehicle.
Note: when installing the pedals: The pedal with “R” symbol is the right pedal, and that with the “L” symbol is the left pedal.

Product Parameters

| Parameters| Standard Edition
---|---|---
Dimensions| Frame materials| Alloy
Dimensions| 18271110cm
Distance from pedal to ground| 100mm
Tyre dimensions| 26 inches
Package dimensions| 1472279cm
Ebike weight| 22.7kgs
Performance parameters| Maximum load| 100kgs
Best riding speed| 20km / h
Maximum speed| 25km / h
Endurance mileage| 50-55km
Maximum climbing angle| 30 degrees
Operating temperature| -10~45°C
Waterproofing grade| IP 54
Type of battery| Lithium-ion battery
Electrical specifications| Battery capacity| 10.4AH
Battery rated voltage| 36V
Motor line type| Power
Riding mode| Power-assisted riding/Electric riding
Motor rated voltage| 36V
Motor rated power| 250W
Charging voltage| DC42V
Input voltage| AC220V
Undervoltage protection value| 31V
Overcurrent protection value| 1.5A
Charging time| 5~8 hours
Product Features| Display| Multi-function LCD screen
Front lighting| Yes
Rear Lighting| Yes
Braking way| Front and rear V brakes
Tyre type| Pneumatic tyre

Remarks:
Electric quantity,load, tyre pressure, pavement environment, chain and axle lubrication degree, etc. will affect the maximum speed; the endurance mileage is measured at a load of 60kg and a speed of 15~25km/h on flat and hardened road under continuous testing from 100% power capacity to 0% power capacity; driving habits, temperature, load, tyre pressure, pavement environment and other factors will affect the endurance mileage.

Product Description and Characteristics

Part description

LCD screen
Mounting bracket
“+” Button
“ i ” Display function button
“-” Button

Technical Data

Rated operating voltage	3 6V /48 V DC
Operating temperature	-20°C ~+45°C
Storage temperature	-20°C ~+45°C

Installation

Install the meter
1. Use M3 Hex Socket Screw 1 to secure the mounting bracket to the left side of the handle bar.
2. Do Not overtighten or it may cause damage to the meter
Connects Cables
Securely connect the cables of B-COCKPiT with E-bike controller by aligning the 2 arrow marks.
Meter interface
The instrument interface is the default interface of b-cockpit.

The status bar will appear on all interfaces, Call reminder needs to be supported through the Bikewise APP When the “Bluetooth logo” flashes, it means that one or more riding data waiting to be synchronized with app has been stored in the instrument

Warning for system settings

If you do not know the relevant knowledge, changing the parameters in the system settings may lead to the abnormal working state of eBike, and even bring security risks. Please consult the eBike manufacturer before modifying the parameters in the advanced settings.

System usage

Initial operation guidance
1. Press “+” and “-” at the same time for 2 seconds to enter the setting menu interface
2. Use “+” / “-” key to select “S8” and other options, and click “i” to confirm, as shown in the figure below and the table below
3. In the corresponding page, use the “+” / “-” keys to increase / decrease parameters
4. The lower right corner is the adjusted parameter
5. After the adjustment of a group of numbers, press the “i” key to jump to the next group of numbers and repeat the operation until all the numbers are set
  
  If it is used with the bikewise app, it is not necessary to manually set the date and time. When Bluetooth is connected to the app for the first time every day, app will automatically adjust the time of the meter to the time consistent with the user’s mobile phone.**According to different configuration of instrument selection function, the value of instrument without this function is invalid.
Button Functions

Other interfaces

Fault code display
Fault code table( he following table takes KM5S as an example)
Daily maintenance and cleaning
Do not immerse the instrument in water or use water spray to clean the instrument. When cleaning, please use a soft cloth dipped in water. Do not use any detergent to wipe
Daily maintenance and cleaning
Do not discard the instrument or any other eBike accessories as household waste. Please comply with the local laws and regulations, and discard or recycle the accessories of eBike in an environmentally friendly manner.

Precautions

Battery and charging:
Charging is only allowed at 0°C~45°C, and discharging is only allowed at -20°C~60°C. The battery must be kept dry. It is strictly prohibited to put the battery in acidic or alkaline liquid. Rain must be avoided, and it shall be kept away from fire, heat, and high-temperature environments. It is strictly prohibited to reverse the battery’s positive and negative poles or damage them, plug in the battery or let it suffer from a short circuit. Please use the original special charger when charging. The charging must not last more than 6 hours, and the charging current does not exceed 2A. When not in use for a long time, please keep the battery in a cool and dry place, and charge it for five hours every month. Users must follow the instructions when charging, otherwise, they will be at their own risk. Attention shall be paid to the type of battery to which the charger is compatible and the applied voltage, and mixing is strictly prohibited. When charging, it shall be placed in a ventilated environment. It is strictly prohibited to charge in a residential building and in an enclosed space or in a hot environment. When charging, insert the battery first, and then supply the mains power; when fully charged, cut off the mains power first, and then unplug the battery connector. When the green light is on, the power shall be cut off in time. It is forbidden to connect the charger to the AC power supply without load for a long time without charging. During the charging process, if the indicator light is abnormal, a peculiar smell occurs, or the charger case is overheating, stop charging immediately and repair or replace the charger. During the use and storage of the charger, be careful not to let foreign matter enter, especially avoid inflow of water or other liquids, so as to avoid short circuit inside the charger. The charger should not be carried with the vehicle. If it is necessary to carry it, it shall be placed in the tool box after shock absorption treatment. Do not disassemble or replace the accessories in the charger by yourself.

Riding:
Do not use until you have read the instructions carefully to understand the performance of the product; do not lend it to anyone who does not manipulate
the product. Before riding, check if the brakes are working. When braking, please apply the rear brake first, and then apply the front brake. Pay attention to the tightness of the brakes. When you find that the brakes are too loose, you can use a internal hexagonal wrench to tighten it. Note that the braking distance shall be increased when you are riding in rain or snow. Applicable age: 16 to 65 years old.
Be sure to wear a safety helmet while riding it, follow the traffic rules, and do not drive on motorized lanes and roads with many pedestrians. Please check the tire pressure before riding. The recommended tire pressure is 35~45 PSI. The speed at downhill and non-brick pavement does not exceed 15km/h. Be careful not to bump the motor vigorously when it is used, and keep the spindle lubricated. Do not ride at more than the maximum load of the car body (maximum load: 120kg) After use, the car cannot be parked in the building’s entrance hall, evacuation stairs, or emergency exit. It must be properly parked in accordance with safety regulations. No one-handed riding!

Disclaimer

After riding, please place the vehicle in a place free from sunlight and rain, not in a residential building; Check the motor and brake frequently; Check the screws of the vehicle and the places to be tightened regularly, and tighten them regularly. Recommended torque: (unit: kgf.cm) handlebar screws 60-80, stem screws 175-200, seat screws 175-200, and wheel screws 320-450; The front and rear wheels of the vehicle shall be located in the center of the fork or frame; Check the spell frequently for any scars, cracks, or excessive wear. The innertube and the air nozzle shall be perpendicular to the hub. The cover tyre that is damaged or excessively worn needs to be replaced immediately, please ask a professional technician to replace your tyre. If your cover tyre accidentally punctures and leaks, please contact a professional technician to repair or replace it.

Maintenance and care:
For the product model, specifications or related information mentioned in this Operation Manual, the company reserves the right of modification and final interpretation; the functions of the specific model mentioned in this Operation Manual are only applicable to that specific model; The product models, specifications, or related information mentioned in the Operation Manual may be changed without notice; without prior written permission of the company, the Operation Manual may not be copied, modified,reproduced, transmitted, or published in any form. Please read the Manual carefully before using the product, and operate in accordance with the Manual, otherwise the company will not be liable for product damage or personal or property damage caused by improper use or error.