LIKE SPORTING Hitway Electric Bike User Manual
- June 4, 2024
- LIKE SPORTING
Table of Contents
LIKE SPORTING Hitway Electric Bike
PRODUCT FUNCTION DIAGRAM
- Display
- Variable speed handlebar
- Brake-lever
- Stem quick release
- Stem
- Stem folding quick release
- Front lights
- front forks
- Wheel hubs
- Disc brakes
- Tires
- Brakes
- Front mudguard
- Front frame
- Folding frame quick-release
- Battery chargıng port
- Folding pedal
- Chain wheel
- Chain
- Motor
- Frame rear part
- Rear mudguard
- Suspension
- Seat post quick-release
- Seat post
- Rear reflector
- Fork shock absorption
Function introduction:
- Charging: Connect the charger to start charging. When the battery is full and the charger indicator turns from red to yellow-green, that means fully charged.
- Electricity display: After starting up, the dashboard lights up and displays the electric quantity. The electric quantity is displayed in four grids, corresponding to high, medium, and low battery.
- Start mode: Refer to Figure 2, zero speed start, when the car is in standby, it can directly start acceleration through the sped control knob.
- Speed up the handlebar: Please speed up slowly, do not twist the handlebar vigorously to prevent damage.
- The detailed function and usage introduction video can be viewed on the company’s official
FOLDING OPERATION DIAGRAM
- The vertical tube can be folded by pressing the red button on the vertical tube folding quick release and then release the quick release.
- The seat tube can be adjusted up and down for quick release and the height of the seat tube can be adjusted.
- The direction of the handlebar can be adjusted through the handlebar adjustment quick release.
- Vertical pipe adjustment and quick release can adjust the height of the vertical pipe.
- Pull the buckle up and release the quick release, the frame can be folded.
- Press the pedal inward with your hand, and then fip it up, the pedal can be folded.
How to take out and install the battery:
- a. Take out the battery: When the frame is folded, refer to the A perspective view. Use a Phillips screwdriver to loosen the two fixings screws of the battery cover, and then open the cover, as shown in Figure 3. Then as shown in Figure 4, use the No. 3 hex key to screw the two battery fixing screws under the drive frame, and after removing the screws, you can take out the battery, as shown in Figure 5
- b. Install the battery: the order of the battery removal method is reverse. Before fixing the battery cover, check the direction of the cover and make sure that the ALX word is on the right, otherwise the battery cannot be connected to the left controller.
PRODUKT-PARAMETER
Remark: Many factors will atfect the max speed, such as power ,load,type pressure, road conditions,chain, lubrication degree etc. Mileage has been measured on basis of temperature 25°C ,load of 60KG,spend of 15-20KM/H, smooth and hard road, and from full battery to dead battery.Ilt also is subjected toother factors, such as driving habits, temperature, load, tyre pressure, road conditions etc.
PRECAUTIONS
Battery and charging:
Charge at 0C~45 C, discharge at -20C~60 C, Please keep the battery dry. It is
strictly forbidden to put the battery in acidic or alkaline liquid, avoid
rain, keep away from fire, heat and high temperature environment. It is also
forbidden to reverse the positive and negative poles of the battery, insert or
short-circuit the battery. When charging. please use the original special
charger, not more than 6 hours, and the charging current does not exceed 2A.
When suspended for a long time, please keep the battery ina dry place, and
charge the battery for five hours every month. The user must charge according
to the instructions, otherwise, customers need to bear the necessary
responsibilities. Please pay attention to the type of battery and the
applicable voltage that the charger can charge,the use of unmatched chargers
is strictly prohibited. When charging, it should be placed in a ventilated
environment. It is forbidden to charge in residential buildings and confined
spaces or in hot and high-temperature environments. When charging, insert the
battery irst, and then add the city power; after charging, cut off the city
power first, and then pull out the battery plug. When the green light is on,
the power supply should be cut off in time, do not connect the charger to the
AC power for a long time without charging. During the charging process, if the
indicator light is abnormal, odor, or the charger case is overheated, stop
charging immediately, and repair or replace the charger. During the use and
storage of the charger, pay attention to avoid the entry of foreign objects,
especially to avoid the flow of water or other liquids, so as not to cause a
short circuit inside the charger. The charger should not be carried with the
vehicle as much as possible. If it is indeed necessary to carry it, it should
be placed in the tool box after shock absorption treatment. Do not disassemble
or replace the accessories in the charger.
Riding:
Do not use it until you read the instructions carefully and understand the
performance of the product; do not lend it to anyone who will not manipulate
the product. Check whether the brake is working before riding the bicycle.
When braking. please use the rear brake first and then the front brake. Pay
attention to the tightness of the brake. If you find that the brake is too
loose, you can use an allen wrench to tighten it. Pay attention to increase
the braking distance when riding in rain or snow. Applicable age: 16 to 45
years old riding. Cyclists must wear safety helmets, comply with traffic
guidelines, and are not allowed to drive on motor vehicle lanes and roads with
many pedestrians. Please check the tire pressure before riding. The
recommended tire pressure is 35 45 PSI. Downhill and non-paved roads do not
exceed 15KM/h. When using the motor, be careful not to hit it strongly and you
need to keep the shaft lubricated. It is not allowed to ride more than the
maximum negative weight of the body (maximum load 120KG) After use, the car
can not be parked in the building entrance hall, evacuation stairs, safety
exit. The rider must be properly parked in accordance with the safety
regulations. One-handed riding is prohibited!
Responsibility statement:
After the ride, please store the car in a place without sunlight and rain, and
cannot be placed in a residential building; Often check the motor and brakes
Regularly check the screws of the car and the places to be tightened, and
tighten regularly. Recommended torque: (unit: kgf.cm) 60-80 horizontal
screws, 175-200 vertical screws, 175-200 seat cushion screws, 320-450 wheel
screws; The front and rear wheels of the vehicle should be located in the
center of the front fork or frame; Always check the wheels for scars, cracks,
or excessive wear. The inner tube and valve should be perpendicular to the
wheel hub and should not be skewed. Damaged or excessive; worn tires need to
be replaced immediately. Please find a professional technician to replace your
tires. If your tires accidentally puncture and leak, please contact a
professional technician for repair or replacement.
Maintenance:
The product model, specifications or related information mentioned in this
manual, the company reserves the right to modify and final interpretation; The
functions of specific models mentioned in this manual only applicable to the
specific model; This use The product model, specifications or related
information mentioned in the manual are subject to any modification or change
without notice; Without the prior written permission of the company, it not
allowed to be copied, modified, reprinted, disseminated or used in any form to
use the content of the manual Please read this user manual carefully and
follow the operation manual before using the product, otherwise, the company
will not be responsible for product damage or personal or property damage
caused by improper use or error
Product Description and Characteristics
Part description
- LCD screen
- Mounting bracket
- “+” Button
- “i” Display function button
- ” Button
Technical Data
Installation
linstall the meter
- Use M3 Hex Socket Screw 1 to secure the mounting bracket to the left side of the handle bar.
- Do Not overtighten or it may cause damage to the meter Connects Cables Securely connect the cables of B-COCKPiT with E-bike controller by aligning the 2 arrow marks.
Meter interface
The instrument interface is the default interface of
b-cockpit.
The status bar will appear on all interfaces, Call reminder needs to be supported through the Bikewise APP When the “Bluetooth logo” flashes, it means that one or more riding data waiting to be synchronized with app has been stored in the instrument
System usage
Initial operation guidance
- Press “+” and “-” at the same time for 2 seconds to enter the setting menu interface
- Use “+” / “-” key to select “S8” and other options, and click “i” to confirm, as shown in the figure below and the table below
- In the corresponding page, use the “+”|”keys to increase / decrease parameters
- The lower right corner is the adjusted parameter
- After the adjustment of a group of numbers, press the “” key to jump to the next group of numbers and repeat the operation until all the numbers are set
If it is used with the bikewise app, it is not necessary to manually set the date and time. When Bluetooth is connected to the app for the first time every day, app will automatically adjust the time of the meter to the time consistent with the user’s mobile phone.”*According to different configuration of instrument selection function, the value of instrument without this function is invalid.
BUTTON FUNCTION
Other interfaces
Fault code display
Fault code table( he following table takes KM5S as an
example)
Daily maintenance and cleaning
Do not immerse the instrument in water or use water spray to clean the
instrument.
When cleaning, please use a soft cloth dipped in water. Do not use any
detergent to wipe
Daily maintenance and cleaning
Do not discard the instrument or any other eBike accessories as household
waste. Please comply with the local laws and regulations, and discard or
recycle the accessories of eBike in an environmentally friendly manner.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>