Einhell GE-PM 53 VS HW B&S Petrol Lawn Mower Instruction Manual

: June 3, 2024
: Einhell

Einhell GE-PM 53 VS HW B &S Petrol Lawn Mower Instruction Manual
Einhell GE-PM 53 VS HW B&S Petrol Lawn Mower

Danger!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care.
Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these
operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regulations and instructions may result in an electric shock, fi re and/or serious injury.
Keep all safety regulations and instructions in a safe place for future use.

Explanation of the warning signs on the equipment (see Fig. 12)

warning signs on the equipment

Read the operating instructions.
Take care of the danger from catapulted parts. Keep a safe distance.
Danger! Sharp blades – Switch off the engine and pull the spark plug boot before doing any maintenance, repair, cleaning or adjustment work.
Fill with oil and fuel before starting the mower.
Caution: Wear ear protection and safety gog gles.
Guaranteed sound power level.
Starting procedure
Engine start/stop lever (I=Engine on; 0=Engine off )
Drive lever (clutch lever)
Empty the tank before you move the mower into cleaning position.

Layout and items supplied

Layout (Fig. 1-13)

1a. Engine start/stop lever (engine brake)
1b. Drive lever (clutch lever)
2. Cleaning scraper
3. Push bar
4a. Debris bag
4b. Mulching adapter
4c. Level indicator
4d. Side ejector fl ap
4e. Side ejector adapter
5a. Ejector fl ap
5b. V-belt
6. Tank fi ller cap
7. Oil fi ller screw
8. Cutting height adjustment
9. Starter cable
10. 1x cable clip
11. Star nut (2x)
12a. Screw (2x)
12b. Washer (2x)
13. Spark plug wrench
14. Hose connection
15. Speed adjuster lever

Items supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating!

Petrol lawn mower
Mulching adapter
Push bar
Catch basket
Side ejector adapter
Cleaning scraper
Cable clip (1x)
Star nut (2x)
Screw (2x)
Washer (2x)
Spark plug wrench
Petrol service manual
Original operating instructions
Safety information

Proper use

The equipment may only be used for the tasks it is designed to handle. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

The petrol lawn mower is intended for private use i.e. for use in home and gardening environments.

Private use of the lawn mower refers an annual operating time generally not exceeding that of 50 hours, during which time the machine is primarily used to maintain small-scale, residential lawns and home/hobby gardens. Public facilities, sporting halls, and agricultural/forestry applications are excluded.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses or for equivalent purposes.

The operating instructions as supplied by the manufacturer must be kept and referred to in order to ensure that the lawn mower is properly used and maintained. The instructions contain valuable information on operating, maintenance and servicing conditions.

Warning! Due to the high risk of bodily injury to the user, the petrol lawn mower must not be used to carry out the following work: Trim bushes,
hedges or shrubs, to cut scaling vegetation, planted roofs, or balcony-grown grass, to clean (suck up) dirt and debris off walkways, or to chop up tree or hedge clippings. Moreover, the lawn mower may not be used as a power cultivator to level out high areas such as molehills.

For safety reasons, the lawn mower may not be used as a drive unit for other work tools or toolkits of any kind.

Technical data

Note:
The enclosed manual from Briggs & Stratton provides detailed technical data on the engine!

Engine type: 150 cc single-cylinder four-stroke engine
Rating: 2.3 kW
Working speed n0: 2850 ± 100 min-1
Fuel: Petrol
Cutting height adjustment: Central, (25-70 mm)
Cutting width: 530 mm Speed
Setting 1 approx. 2.7 km/h
Setting 2 approx. 3.2 km/h
Setting 3 approx. 3.7 km/h
Setting 4 approx. 4.2 km/h
Weight: 39 kg

Danger!
Sound and vibration

LpA sound pressure level : 83.5 dB(A)
KpA uncertainty :. 3 dB
LWA sound power level: 95.8 dB(A)
KWA uncertainty : 1.85 dB
Guaranteed sound power level:98 dB (A)

Vibration emission value ah
= 6.28 m/s2
K uncertainty = 1.5 m/s2

Wear ear-muff s.
The impact of noise can cause damage to hearing.

Long work periods should be avoided due to the development of high noise and vibration levels.

Keep the noise emissions and vibrations to a minimum.

Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever necessary.
Switch the appliance off when it is not in use.

Caution!
Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

Damage to hearing if no suitable ear protection is used.
Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Before starting the equipment

Assembling the components

Some parts of the equipment come disassembled. For quick and easy assembly, read and follow the instructions below.

Note! You will need the following additional tools (not supplied) for assembly, and also for maintenance work:

One flat oil drip tray (for changing the oil)
One 1 liter measuring jug (oil/petrol resistant)
One petrol can
One funnel (suitable for the tank’s petrol filler neck)
Household wipes (to wipe up oil/petrol residue; dispose of these at a filling station)
One petrol suction pump (plastic, available from DIY stores)
One oil can with hand pump (available from DIY stores)
Engine oil

Assembly

Fit the push bar (Item 3) as shown in Fig. 3a.

For fastening choose one of the holes (Fig. 3a/Item A) to suit the required height of the handle. Important! The identical height must be set on both sides.

Insert the grip of the starter cable (Item 9) into the hook provided for that purpose as shown in Fig. 3b.
Fasten the actuator cables to the push bar with the supplied cable clips (Item 10) as
shown in Fig. 3c
.
Lift the ejector fl ap (Item 5a) with one hand and hook in the grass bag (Item 4a) as shown in Fig. 4a.

Adjusting the cutting height

Warning! Adjust the cutting height only when the engine has been switched off .

The cutting height is centrally adjusted with the cutting height adjustor lever (Fig. 6/Item 8). Different cutting heights can be selected.
Actuate the adjustor lever and pull it to the required position. Let the lever click into position.

Operation

Note!
The engine comes without oil and petrol.
Therefore, be sure to add oil and petrol before starting the engine.

The enclosed engine manual from Briggs & Stratton provides maintenance information and maintenance interval information on the engine.

Warning: Never use more than one safety petrol can. Do not smoke when refueling. Switch off the engine before refueling and allow the engine to cool down for a few minutes.

Ensure that the ignition cable is connected to the spark plug.

Carrying out a safety test on the engine start/ stop lever

The lawn mower comes equipped with an engine start/stop lever (Fig. 5a/Item 1a) in order to prevent it from starting up unintentionally and to ensure that the engine and blade stop quickly in case of danger. The lever must be actuated (Fig. 5b) before the lawn mower is started. When the engine start/stop lever is released, it must return to its initial position (Fig. 5a).

Before you start mowing, you should run through this process several times in order to ensure that the lever and actuator cables are working properly.

Repeat the test several times after the engine has started up. When the engine start/stop lever is released, the engine must stop within a few seconds. If not, contact Customer Service.

Danger: The blade begins to rotate as soon as the engine is started.

Starting the engine

For detailed information on starting the engine, refer to the enclosed manual from Briggs & Stratton.

Drive unit

Drive lever/clutch lever (Fig. 5a/Item 1b):
If you press this (Fig. 5c) the clutch for the drive will be closed and the lawnmower will start to move with the engine running. Release the drive
lever in good time to stop the moving lawnmower. Practice starting and stopping before you use the mower for the first time until you are familiar with controlling the mower.

Setting the speed (Vario Speed)
Up to 4 diff erent speed settings can be selected.
Setting 1 is for the slowest speed, setting 4 is for the fastest speed. To set the speed, move the lever (Fig. 13/Item 15) into the required position.

Important! The speed is allowed to be set only when the engine is running and the drive lever (Item 1b) is actuated.

Tips on mowing properly

Danger!
Never open the chute flap when the grass bag has been detached (to be emptied) and the engine is still running. The rotating blade can cause serious injuries!

Always carefully fasten the chute flap and debris bag. Switch off the engine before you remove them.

Whenever you need to perform any kind of adjustment, maintenance or repair work, switch off the engine and wait until the blade no longer rotates. Pull off the spark plug connector.

Mowing
The engine is confi gured for an optimal grass cutting speed, for ejecting grass into the debris bag, and for many years of use.

Only use a sharp blade that is in good condition.
This will prevent the grass blades from fraying and the lawn from turning yellow.

Try to mow in straight lines for a nice, clean look.
The swaths should overlap each other by a few centimeters in order to avoid stripes.

Keep the underside of the mower housing clean and remove grass build-up. Deposits not only make it more difficult to start the mower; they decrease the quality of the cut and make it harder for the equipment to bag the grass.

Always mow along inclines (not up and down).
You can prevent the lawn mower from slipping down by holding a position at an angle upwards. Select the cutting height according to the length of the grass. If necessary, mow a number of times so that you never cut more than 4cm of grass in one go.

Switch off the engine before doing any checks on the blade. Keep in mind that the blade continues to rotate for a few seconds after the engine has been switched off . Never attempt to manually stop the blade. Regularly check to see if the blade is securely attached, is in good condition and is sharp. If the contrary is the case, sharpen the blade or replace it. In the event that the blade strikes an object, immediately switch off the lawn mower and wait for the blade to come to a complete stop. Then inspect the condition of the blade and the blade mount. Replace any parts that are damaged.

Mulching (Fig. 4b)
In mulching mode the cuttings are shredded in the enclosed mower housing and then spread back onto the lawn. It is not necessary to gather and dispose of the grass.

Mulching is only possible if the lawn is relatively short. ).

To use the mulching function, disconnect the debris bag, slide the mulching adaptor into the ejector opening (Item 4b) and close the ejector opening.

Side ejector (Fig. 4b/4c)

You must fit the mulching adapter (Item 4b) in order to use the side ejector. Hook in the side ejector adapter (Fig. 4c/Item 4e) as shown in Fig. 4c.

Rear ejector (Fig. 4d)

To use the rear ejector function you must open the ejector fl ap (Fig. 4d/Item 5a) slightly. Lock it in place with the locking lever (Fig. 4d/Item A).
Swing up the locking lever and insert its foot into the recess provided (Fig. 4d/Item B). The mulching adapter (Item 4b) is not allowed to be fi tted when the rear ejector is used.

Switching off the engine

All you have to do to switch off the engine is release the engine start/stop lever (Fig. 5a/ Item 1a). Pull off the spark plug connector from the spark plug in order to prevent the engine from starting. Before you start the engine again, check the cable of the engine brake. Check that the actuator cable is correctly fitted. If the switch-off cable is kinked or damaged, it must be replaced.

Emptying the debris bag

When the debris bag is full, the air throughput will be low and the level indicator (4c) will be up close against the debris bag (Fig. 11). Empty the debris bag and clear out the ejector chute.
Danger! Before taking off the debris bag, switch off the engine and wait until the blade has come to a stop.

To take off the grass basket, use one hand to lift up the chute flap and the other to grab onto the basket carry-handle. Remove the basket (Fig. 4a).
For safety reasons, the chute flap automatically falls down after removing the grass basket and closes off the rear chute opening. If any grass remains in the opening, it will be easier to restart the engine if you pull the mower back approximately 1m.

Do not use your hands or feet to remove clippings in or on the mower housing, but instead use suitable tools such as a brush or a hand broom.

In order to ensure that the majority of grass clippings are picked up, the inside of both the grass bag and especially the air grill must be cleaned
after each use.

Reattach the grass bag only when the engine is switched off and the blade is stopped.

Using one hand, lift up the chute flap, while grabbing onto the basket handle with the other. Hang in the basket from the top.

Cleaning, maintenance, storage, transport and ordering of spare parts

Danger!
Never work on or touch any current-conducting parts of the ignition system while the engine is running. Pull the spark plug boot from the spark boot before doing any maintenance or assembly work. Never carry out any work on the equipment while the engine is running. Work that is not described in these operating instructions, should only be carried out by authorized workshops.

Cleaning

Cleaning in the vertical cleaning position (Fig. 9a/9b)

The lawn mower should be cleaned thoroughly every time after it has been used. This applies in particular to its underside and the blade mount.
Note: Before tilting the lawn mower into the vertical cleaning position, use a petrol extraction pump to drain all the fuel out of the fuel tank. Do not tilt the lawn mower by more than 90 degrees.

Important! Before moving the mower into the vertical cleaning position, switch off the engine and pull out the spark plug connector. Important!
Place the mower only on a firm, level surface.

Open the star nuts (Item 11).
Press the lower push bar apart and swing it open (Fig.9a).
Move the mower into the vertical cleaning position (Fig.9b).
Clean the bottom side of the mower with the cleaning scraper (Fig.1/Item 2).

Warning!

Sharp blades! Wear gloves during the cleaning work.

It is easiest to remove dirt and grass immediately after mowing. Dried grass remnants and dirt may impair the mowing operation. Check if the grass ejector chute is free of grass remnants and remove any if necessary. Never clean the mower using a high-pressure cleaner. The engine must remain dry. Do not use aggressive cleaning agents such as cold cleaners or petroleum ether.

Warning!

Leave the mower in the vertical cleaning position only for as long as necessary because in this position there is a considerable risk of injury.
Never leave the mower unsupervised.
Keep children away

Automatic cleaning of the mowing deck by means of the hos connection (Fig. 10/ Item 14)

The mowing deck is fitted with a hose connection (Item 14) (suitable for conventional garden hose couplings). The lawn mower should be cleaned thoroughly every time after it has been used.

Warning!

Switch off the engine before you do any work on the mower. Risk of injury from rotating blades.
Keep the ejector fl ap (Item 5a) closed when you carry out the cleaning. Risk of injury from catapulted parts.

Place the mower on a firm, level surface. The mower must stand on 4 wheels as in mowing mode. Take off the catch basket (Item 4a) and
make sure that the mulching adapter (Item 4b) has been removed.
Connect the water hose to the hose connection (14).
Turn on the tap. Water will fl ow into the inside of the mowing deck.
Start the engine. See section 6.1.
Automatic cleaning will begin. The rotating blades will cast the water against the mowing deck and therefore clean it from the inside.
A cleaning period of 1-2 minutes is enough when carried out regularly.

To remove dried grass residues we recommend carrying out several cleaning cycles. Wait a few minutes between the cleaning cycles so that the dried grass can soak and soften up

Important!

Never clean the mower using a high-pressure cleaner. The engine must remain dry. Do not use aggressive cleaning agents such as cold cleaners or petroleum ether.

Maintenance

Note: Dispose of soiled maintenance material and operating materials at the appropriate collection point.

Petrol engine

The enclosed engine manual from Briggs & Stratton provides maintenance information and maintenance interval information on the engine.

Blades

For safety reasons, have all blade sharpening, balancing and mounting work carried out by an authorized service center. To achieve optimal results, we recommend having the blades checked once a year.

Changing the blades (Fig. 7/pos. A)

When changing the cutting unit, be sure to use only genuine replacement parts. The identification mark on the blade must correspond with the number specified in the spare parts list.
Never install a blade from a different manufacturer.

Damaged blades

If, in spite of all caution, the blade comes into contact with an obstacle, switch off the engine immediately and pull off the spark plug connector.
Tilt the lawn mower to the rear and check the blade for damage. Damaged or bent blades must be replaced. Never straighten a bent blade. Never work with bent or heavily worn blades as this will result in vibrations, causing further damage to the mower.

Warning! Risk of injury when working with a damaged blade.

Axles and wheel hubs

Grease should be applied to the axles and wheel hubs once per season.
To do so, remove the wheel caps with a screwdriver and loosen the fastening screws on the wheels.

Care and adjustment of the actuator cables

Oil the actuator cables at regular intervals and check that they move easily.

Inspecting the V-belt

To inspect the V-belt you must remove the V-belt cover (Fig. 8/Item 5b).

Repairs

After carrying out any repair or maintenance work, ensure that all safety parts are installed and in perfect condition.

Keep potentially hazardous parts out of reach of other persons and children.

Note! In accordance with the German Product Liability Act, we are not liable for any damages if they result from improper repairs to the product or if parts are replaced by items other than genuine parts or parts approved by us. Furthermore, we are not liable for any damages if they result from improper repairs to the product. Arrange for your customer service or an authorized workshop to do the work. The same applies to accessory parts.

Operating times

Please observe the regulations concerning lawn mower operating times, which may diff er from town to town.

Preparing the mower for long-term storage

Warning! Do not empty the petrol tank in enclosed areas, near fire or when smoking. Petrol fumes can cause explosions and fire.

Drain the petrol tank using a petrol extraction pump.
Start the engine and run it until the tank and fuel line are completely empty and the engine stalls.
The enclosed engine manual from Briggs & Stratton provides maintenance information and maintenance interval information on the engine.
Clean the cooling fins of the cylinder and the housing.
Be sure to clean the entire equipment to protect the paint.
Store the equipment in a well-ventilated place.

Preparing the mower for transport

Warning! Do not empty the petrol tank in enclosed areas, near fire or when smoking. Petrol fumes can cause explosions and fire.

Drain the petrol tank using a petrol extraction pump.
Always let the engine run until it has used up the remainder of petrol in the tank.
Empty the engine oil from the warm engine.
The enclosed engine manual from Briggs & Stratton provides maintenance information and maintenance interval information on the engine.
Remove the spark plug connector from the spark plug.
Clean the cooling fins of the cylinder and the housing.
Unhook the starter cable from the hook (Fig. 3b). Slacken the connection shown in Fig. 3a on the left and right of the push bar and swing down the push bar (Fig. 9a). Make sure that the actuator cables do not get kinked when the bar is pulled up.
Wedge a few layers of corrugated cardboard between the upper and lower push bars and the engine in order to prevent any chafing.
Secure the load sufficiently so that it cannot slip and cause damage or injuries during transportation.

Consumables, wear materials and spare parts

Spare parts, consumables and wear materials such as engine oil, V-belts, spark plugs, air filter inserts, petrol filters, batteries and blades are not covered by the warranty.

Ordering replacement parts:

Please quote the following data when ordering replacement parts:

Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required

For our latest prices and information please go to www.isc- gmbh.info

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

Troubleshooting guide

Warning: Switch off the engine and pull out the spark plug boot before making any checks or adjustments.

Warning: If, after making an adjustment or repair to the engine, you let it run for a few minutes, remember that the exhaust and other parts will get hot. Do not touch these parts as they may burn you.

Fault	Possible cause	Remedy
The equipment does not operate smoothly and vibrates intensively

Bolts loose
Blade attachment is loose
Blade imbalanced

|

Check bolts
Check blade attachment
Replace blade

The engine does not start|

Engine start/stop lever is not pressed
Throttle lever in wrong position (if provided)
Spark plug defective
Fuel tank empty
Fuel pump (primer) not actuated (if provided)

|

Press the engine start/stop lever
Check setting (if provided)
Replace spark plug
Top up fuel
Actuate the fuel pump (primer) (if provided)

Engine does not run smoothly|

Air filter dirty
Spark plug dirty

|

Clean the air filter
Clean the spark plug

Lawn turns yellow, uneven cut|

Blade is not sharp
Cutting height too small
Engine speed too low

|

Sharpen blade
Adjust to the proper height
Set the throttle lever to max. (if provided)

Grass chute is not clean|

Engine speed too low
Cutting height too small
Blade is worn – Grass bag is clogged

|

Set the throttle lever to max.
Set properly
Replace the blade
Empty the grass bag

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown.

Please note the following terms under which guarantee claims can be made:

These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the
defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.
The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
To make a claim under the guarantee, please register the defective device at: www.isc-gmbh.info.
Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.

Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.