Berger BPS1000 Powerstation 1000 W User Manual

Bedienungsanleitung
Powerstation BPS1000 / BPS1500
User Manual

SAFETY AND HAZARD NOTES

(PLEASE READ COMPLETELY BEFORE USE)
To avoid danger to life and limb and to prevent damage to the appliance, please observe the following instructions before using the product.

• Please read this manual carefully to ensure proper use of the Power Station and to familiarise yourself with the use of the unit and the power supply.
• Keep the Power Station out of the reach of children and store it in a safe place.
• As there may be a voltage of up to 250V inside the Powerstation, never open the unit, there is a risk of electric shock.
• As this appliance generates a voltage similar to that of a household socket, you must handle it with great care and caution to avoid life-threatening electric shock.
• Keep the appliance away from heat sources or fire.
• Do not use the unit in the rain, do not expose it to water or strong humidity.
• Do not place any objects on the unit.
• Make sure that the ventilation slots are not covered during operation, do not insert any objects into the slots.
• Avoid bumping against the unit or dropping it.
• Do not use the unit if it is externally damaged.
• The power station may only be charged with the supplied mains adapters.
• Short circuits can occur at the output sockets through contact with metallic objects, this must be avoided at all costs, if a short circuit occurs, the causes must be eliminated.
• The power station must not be charged in ambient temperatures below 0°C as this may damage the lithium battery inside.
• Charge the unit every 3 months if it will not be used for a long period of time to avoid deep discharge and possible damage.
• The seller or the manufacturer are not responsible for any damage to the unit or your equipment caused by improper use of the Power Station.
• This manual must always be kept together with the product, please do not throw the manual away, always pass the unit on only together with the manual, this manual must also be given with the product when it is sold.

WARNING! The Power Station must never be used as a mains replacement or feedin source for existing electrical systems (e.g. in mobile homes, caravans, mobile homes or houses). Plug the mains plug of the intended consumer (terminal devices) directly into the mains socket of the power station, do not use multiple sockets. Non-observance can lead to non-functioning of the protective measures against shutdown in the event of a fault and thus to danger to life and limb.

PRODUCT DESCRIPTION

Berger BPS1000/BPS1500 is a multifunctional portable energy storage for indoor and outdoor use. It has a safe lithium-ion battery and inverter conversion technology with light weight, high capacity and high performance to provide portable energy solutions, its main function is as follows:

• Pure sine wave output
• DC output 12V10A; 4 x USB; QC3.0
• Smart LCD screen
• Supports solar charging
• Supports in-car charging (external car charging adapter is included)

The BPS1000/BPS1500 can be used to power smart products such as mobile phones, satellite phones, digital cameras, mobile drivers, digital cameras, tablets, car starters, outdoor lighting, water pumps, postal and telecommunication systems, medical equipment and in the following fields: Finance, research, military, science, media, tourism, disaster relief, medical aid and areas with widespread power shortages.
Please read the operating instructions carefully before use and keep them together with the proof of purchase so that you have them to hand later.

OPERATING ELEMENTS

1. Power switch: Press the power switch lightly to initialise the dynamic percentage display. The entire screen lights up and is displayed normally again after 1 second. At the same time, the brightness of the LCD display is set to 100 %. At this time, the unit is on, lightly press the power switch again, the brightness of the LCD changes to 50 % (lightly press the power switch to adjust the brightness of the LCD after it is on), or then press and hold the switch for 1 second to turn off the unit and put it into sleep mode.

2. DC switch: After switching on the unit, press and hold the DC switch for 1 second, the USB and 12 V output will be switched on, at the same time the LCD screen will display the battery percentage, DC discharge time (h), DC discharge power and DC OUT icon (shown as Display_1). After switching on, lightly press DC switch, switch the real-time battery percentage/battery real-time voltage mode. Press and hold DC switch for 1 second to turn off USB and 12V output.

3. AC switch: After switching on, press and hold the AC switch for 1 second, the AC output is switched on, at the same time the LCD screen shows the percentage of battery capacity / battery voltage, AC discharge time (H), AC discharge power, percentage of AC output power „AC OUT“ icon (shown as Display_2). After the AC output is switched on, press the AC switch lightly to switch the mode AC discharge power + AC discharge time / AC discharge voltage + PF value (see picture Display_3). Press and hold the AC switch for 1 second, the AC output switches off.
   |
   ---|---

4. LCD display
   

5. USB output: When the DC switch is on, it can power up to 4 USB devices.
   

6. Cooling fan output

7. DC output: 16MF two-pin plug (1 is positive 2 is negative) When the DC switch is on, it can supply power to DC devices (12V 10A)

8. DC input: 16MF four-pin connector (1.2 is positive; 3.4 is negative) Connector for charging the power station. (IN 29.4 – 40V 10A)

9. AC Power outlet x 2: When the AC is switched on, you can connect 230V consumers to the socket.

10. Cooling air intake

OPERATING INSTRUCTIONS AND PRECAUTIONS

To ensure safe transportation, the power station is not fully charged, please fully charge the power station before use. If you want a quick charge, please use our standard original mains adapter for charging, or use a 36V 200~300W solar panel for charging. To ensure safety, please use only our standard charger. Please disconnect the charger when the Power Station is fully charged.
4.1 USE OF THE AC OUTPUTS
Please observe the following instructions before use:

1. Make sure that the input voltage and frequency of the consumer matches the BPS1000 & BPS1500.
2. Make sure that the rated power of the consumer is below 1000W (BPS1000) / 1500W (BPS1500), it is better if the rated power does not exceed 80%.

• Failure to do so may damage the power station or cause it to shut down.

• If the power of your connected load is higher than 1000W (BPS1000) / 1500W (BPS1500), please choose another power station with higher power.
  Note: Some appliances, when switched on, have a much higher power than the rated power, e.g. the starting current of appliances with inductive load is usually 3-8 times higher than the rated power, the starting power of energy saving lamps is dozens of times higher than their rated power. If the starting power is higher than the peak power of the Powerstation, the overload protection triggers and switches off the Powerstation.
  The Power Station is equipped with overload, short-circuit and overtemperature protection. If the following conditions are met, the power station switches off the sockets:

  • If the load power of the unit is higher than the rated power of the power station
  • If there is a short circuit in the connected load
  • If the temperature in the unit is too high
  • If the battery voltage is too low

4.2 FUNCTIONALITY
Step 1: Lightly press „ON/OFF“ after the unit is switched on, press and hold „AC ON/OFF“ for 1 second to switch on the AC output. Step 2: Check that the input voltage and frequency of the load match the power station.
Step 3: Check the load power and make sure it does not exceed the max. power of the power station.
Step 4: Connect the unit to this socket and switch on the load switch.
Step 5: After using the power station, lightly press the ON/OFF button to switch off.
Step 6: When the capacity is used up or the remaining capacity is too low, recharge the power station for the next use. 4.3 CHARGING THE POWERSTATION
You can use the following methods to charge the Powerstation:

1. use the standard mains adapter, to do this connect the mains cable to the adapter, on the other side connect the DC plug to the input charging socket of the  owerstation, then plug the 230V mains plug into a 230V household socket.
   

2. charging with the car charging cable: after you have started the car, plug the 12V connector into the 12V socket of the car, the other side connects to the input connector of the powerstation.

3. solar charging – if you use a solar panel to charge the Powerstation, connect the supplied adapter cable to the solar cable of the solar panel, then connect the other side of the adapter to the input connector of the Powerstation (please make sure that the maximum voltage of the solar panel is not more than 40V and the minimum voltage is not less than 29.4V).

Note:

1. our standard power bank can only be used in our power station, please do not use it on other devices and keep it away from rain.
2. when using car charging and solar charging, please make sure the positive and negative connections are correct.
3. if the portable power station is not used for a long time, the built-in battery will discharge and may be damaged. Therefore, please charge the power station every 3 months.

4.4 USE OF THE DC 12V OUTPUTS AND THE USB OUTPUTS

DC output 16MF double pole plug, press the DC switch for 1 second, turn on DC 12V output, its rated current is 10A, press the DC switch again for 1 second, the DC  output turns off.

USB outputs, press the DC switch for 1 second, USB outputs are switched on, press the DC switch again for1 second to switch off the USB outputs.

Description

| BPS1000|

BPS1500

---|---|---
Output  power| 1000W| 1500W
Peak performance| 2000W| 3000W
Output  voltage AC| 2 x AC 230V/50Hz ±5%
Output-waveform| Pure sine wave
Output  voltage DC| DC 12V 10A; 4 x USB Quick Charge 3.0
Battery capacity| 1028 Wh (25.2V; 40.8Ah)| 1512 Wh (25.2V; 60Ah)
Battery-Typ| Lithium-ion
Charging  time| 7– 8 h
Charging  voltage and current| Auto 13V (with Adapter) DC 29,4V/5A; Solar 36V/20A (MAX); AC 80V-260V, 29,4V/9A
Protection| Overvoltage, undervoltage, overtemperature, overload, AC short circuit
Operating  temperature| 0°C – 45°C (Charge)

-20°C – 60°C (Discharge)

Dimensions (WxDxH)| 352 x 187 x 260 (mm)
Case material| UL94-V0; PC+ABS
Netto weight| 11,6 kg| 12,5 kg

ENVIRONMENT

ELECTRICAL SPECIFICATIONS

Solar charge
Voltage| 29,4 – 40| V DC
Current| ≤ 20| A
AC output
Nominal voltage| 230 ± 5%| V AC
Nominal frequency| 50 ± 1%| Hz
Nominal power| 1000 bzw.1500| W
Harmonic distortion| < 3%|
Transformation efficiency| ≥ 85%|
DC output
USB voltage| 5 ± 5%| V DC
USB current, max.| 2,0 ± 10%| A
DC cigar connection output voltage| 12 ± 5%| V DC
DC cigar connection output current| 10 ±10%| A

SHUTDOWN CONDITIONS

Inverter
Overtemperature| Inverter temperature ≥ 65°C| °C| No AC output, wait until temperature drops
Overload| > 1000 (PS 1000)

1500 (PS 1500)| W| No AC output, disconnect load and restart
AC output circuit| | W| No AC output, disconnect load and restart

Note: If the AC output has switched off due to one of the above conditions, disconnect the load, switch off the AC switch and switch it on again.

DC controller

charge after  reaching the voltage

Battery

Overcharge protection for one cell; Voltage protection| 4,2 per cell| V| Separates the charge
---|---|---|---
Deep discharge protection| 2,8 per cell| V| Output will be switchedw
off
Batterypack Overtemperature protection| ≥ 65| °C| Input and output are
switched off
Short circuit protection| Ja| | Output is switched off
after short circuit
Overcurrent protection for the battery pack| 120 – 180| A| Output is switched off
after overcurrent

TROUBLESHOOTING

No AC output after pressing the

AC switch, LCD display is normal

| Over temperature| Disconnect the load
Overload| Check the power  con- sumption  of the connected consumer,  reduce power  or switch off
Under voltage| Charging
USB without  output| USB output/display switch is off| Press the ON/OFF switch to switch on.
12V or USB DC consume  energy quickly| AC switch is on; standby current is too high| Switching off the AC switch during DC output
Unit is not fully charged  by solar charging| The solar panel is not suitable and/or the solar radiation is too low| Select a suitable solar module and ensure that  the charging voltage is higher than  13V.

SUPPLY

• BPS1000 or BPS1500 Powerstation
• Mains adapter
• Mains cable
• DC output cable 1+4; 4 in 1 cable
• Car charger cable (cigarette lighter)
• Solar cable plug (M4)
• USB adapter
• User manual

TRANSPORTATION

Since a lithium battery is permanently installed in the Berger Powerstation BPS1000 and BPS1500, the regulations for lithium batteries also apply. When transporting lithium batteries, all national and international regulations and laws must always be observed. Transport may only take place in the original packaging or packaging corresponding to  this. Never transport damaged LiFePO4 batteries; this may only be done in prescribed containers. LiFePO4 batteries installed in devices are classified according to UN3481,  Class 9 during transport.

DISPOSAL

If possible, put the packaging material in the appropriate recycling waste.
Note on environmental protection:
From the date of transposition of the European Directives 2012/19/EU into national law, the following applies: Electrical and electronic equipment must not be disposed of with household waste. The consumer is legally obliged to return electrical and electronic devices at the end of their service life to the public collection points set up for this  purpose or to the point of sale. Details are regulated by the respective national law. The symbol on the product, the instructions for use or the packaging indicates these regulations. By recycling, material recovery or other forms of recovery of old appliances/batteries, you are making an important contribution to protecting our environment.

MAINTENANCE AND CARE

The Berger Powerstation does not require any regular maintenance apart from cleaning with a damp cloth (no chemical cleaning agents), it is absolutely maintenance-free. If  the portable power station is not used for a long time, the built-in battery will discharge and can be damaged. Therefore, please charge the Powerstation every 3 months.

EU DECLARATION OF CONFORMITY

With the CE mark, Fritz Berger GmbH declares that this product complies with the basic requirements and other relevant regulations of the EU directive. If required, the  declaration of conformity can be requested at info@fritz- berger.de.

CUSTOMER SERVICE/WARRANTY

All Berger Powerstation are manufactured according to the strictest quality criteria and Berger guarantees that the units are delivered in perfect condition. Berger grants the statutory warranty of 2 years on production and material defects that were present at the time of delivery of the product. The warranty does not apply to defects resulting from natural wear and tear, improper use, opening of the appliance, modifications to the appliance, lack of maintenance or failure to observe these instructions. Any use of the product is at your own risk. A warranty claim can only be accepted if a copy of the purchase receipt is enclosed when the product is returned. The warranty shall in no case exceed the value of the product.

In all other respects, the General Terms and Conditions of Fritz Berger GmbH apply. By putting the product into operation, you accept the above conditions and assume full responsibility arising from the use of this product.

The values given by Berger regarding weight, size or technical data are to be understood as approximate values and no formal obligation for this information. Technical changes, which are made in the interest of the product even without notice, may also result in other values. If you have any questions about your power station after your purchase or during operation, please contact the seller of the product.
He will explain the further procedure to you. If the seller is unable to help you, please contact Berger. Please contact us in advance by e-mail with information and explanation of the problem, possibly with pictures. Should it occur that you wish to return a Powerstation to us, please note the following instructions for quick processing:
If possible, use the original packaging as the shipping box. If you no longer have the original packaging, please ensure adequate protection against transport damage with suitable (UNcertified) packaging.If the goods are not shipped in the original packaging or UN-certified packaging, we must charge for the new packaging when the product is returned. Shipment is at the shipper‘s own risk.

Please enclose the following with the return shipment:

• Copy of the invoice
• Reason for the return
• A precise and detailed description of the fault

Service contact for questions and address for returns:
Fritz Berger GmbH
Fritz-Berger-Str. 1
92318 Neumarkt
Germany
Telefon: 09181 / 330 – 100
Mail: service@fritz-berger.de
When contacting us directly, please have your customer or invoice number and the item number ready.

Fritz Berger GmbH
Nr. 359240 / Nr. 359260
Fritz-Berger-Str. 1
92318 Neumarkt, Germany
Tel. (+49) 91 81 – 330 100
E-Mail: service@fritz-berger.de
Fax (+49) 91 81 – 330 500
Web: www.fritz-berger.de

References

• Global consulting | Roland Berger
• Fritz Berger – Spezialist für Campingzubehör und Freizeit - Fritz Berger Campingbedarf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>