ZEBRA DS3608 Digital Scanner User Guide

ZEBRA DS3608 Digital Scanner

Specifications

• Product: DS3608 Digital Scanner
• Scanner Type: Corded Digital Scanner
• Features: Scan Window Trigger, LEDs, Beeper, Cable Attachment
• Interface Options: USB, RS-232, Keyboard Wedge

Product Usage Instructions

Setting up the DS3608 Scanner

1. Insert the cable fully into the scanner and ensure the connector is flush with the scanner surface.
2. Loosen the metal lock plate screws using a PH1 driver.
3. Slide the lock plate to the fully locked position.
4. Tighten the screws using a PH1 driver and torque to 5.8 kgf-cm (5.0 lbf-in).

Host Interface Connections Setup

USB Interface
For USB connection, scan one of the bar codes below to set the host interface:

• * *USB KEYBOARD (HID)

  • USB CDC HOST
  • IBM TABLE TOP USB

RS-232 Interface

For RS-232 connection, scan one of the bar codes below to set the host interface:

• *STANDARD RS-232
• ICL RS-232
• NIXDORF RS-232 MODE A

Keyboard Wedge Interface
For Keyboard Wedge connection, scan one of the bar codes below to set the host interface:

• NIXDORF RS-232 MODE B OPOS/JPOS

Default Settings and Emulation
To set defaults or configure emulation modes, scan the corresponding bar codes provided in the user manual for various port settings.

FAQ (Frequently Asked Questions)

1. Q: How can I change the host interface type for the DS3608 Scanner?
   A: You can change the host interface type by scanning the appropriate bar code from the user manual based on your connection requirements.

2. Q: Where can I find the latest version of the DS3608 user guide?
   A: You can find the latest version of the user guide on Zebra’s support website at zebra.com/support.

Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.

Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com/warranty.

For Australia Only
For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road, #05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies Corporation at +65 6858 0722. You may also visit our website: zebra.com for the most updated warranty terms.

Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Zebra Global Customer Support Center at: zebra.com/support. For the latest version of this guide go to: zebra.com/support.

Introduction
The DS3608 corded digital scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a lightweight laser scanner, ensuring comfort and ease of use for extended periods of time.

Features

Cable Attachment

1. Insert cable fully so that the connector is flush with the scanner surface.
2. Loosen metal lock plate screws using a PH1 driver.
3. Slide lock plate to fully locked position.
4. Tighten screw using a PH1 driver, and torque to 5.8 kgf-cm (5.0 lbf-in).

Host Interface Connections and Setup

USB

Scan one of the bar codes below
The interface cable automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan another host bar code below.

USB

Scan one of the bar codes below
The interface automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan another host bar code below.

RS-232

Keyboard Wedge

Scan a bar code below
The Auto-Host Detect Cable feature automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan the IBM PC/AT and IBM PC COMPATIBLE bar code below.

IBM 46XX

Scan one of the bar codes below
The Auto-Host Detect Cable feature automatically detects the host interface type, but there is no default setting. Scan one of the bar codes below to select the appropriate port.

Set Defaults Bar Code

HAND-HELD SCANNER EMULATION (PORT 9B)

TABLE-TOP SCANNER EMULATION (PORT 17)

Set Defaults Bar Code

RETURN TO FACTORY DEFAULTS

Enter Key Bar Code (Carriage Return/Line Feed)
Add an Enter key after scanned data.

ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)

Tab Key Bar Code
Add a Tab key after scanned data.

USB Caps Lock Override

USB – OVERRIDE CAPS LOCK KEY (ENABLE)

*USB – DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)

DS3608 Aiming

HP/HD/XR Aiming
Cover the entire bar code with the aiming pattern to ensure it is within the field of view.

SR Aiming
For best results, aim the aiming dot at the center of the bar code.

ER Aiming
Cover the entire bar code with the aiming pattern to ensure it is within the field of view.

DP Aiming
For best results, aim the aiming dot at the center of the bar code.

Recommended Usage -Optimum Body Posture

Avoid Reaching

LED Indications

Beeper Indications

Troubleshooting

Ensure scanner is programmed to read type of bar code being scanned.
Bar code unreadable.| Ensure bar code is not defaced; try scanning test bar code of same bar code type.
Distance between scanner and bar code incorrect.| Move scanner closer to, or further from bar code.
Scanned data incorrectly displayed on host.| Host interface not configured properly.| Scan appropriate host parameter bar codes.
Region improperly configured.| Select appropriate country and language encoding scheme.

123Scan2
123Scan2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via a bar code or USB cable. For more information, visit: zebra.com/123Scan2.

Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to Model Number: DS3608.
All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Local language translation zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s authority to operate the equipment.

• DS3608 Declared maximum operating temperature: 50°C

CAUTION Only use Zebra approved and UL Listed accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source.

Regulatory Markings
Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DoC is available at: zebra.com/doc.

Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.

Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle. Position the device within easy reach. User should be able to access the device without removing their eyes from the road.

IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.

Restricted Use Locations
Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations.

Optical Devices Laser
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.

CAUTION: Use of controls, adjustments, or the performance of procedures other than those specified in the supplied product documentation may result in hazardous laser light exposure.

Maximum output: 2 mW
Pulse duration: 4 ms
Beam divergence: 42 °
Repetition rate: 16.7 ms

Scanner Labeling

DS3608-SR LED – Exempt Risk Group

• DS3608-ER Class 2
• DS3608-HP Class 2
• DS3608-HD Class 2
• DS3608-DP Class 2
• DS3608-XR Class 2

Labels read:
Laser Light — do not stare into beam.

1. Class 2 Laser product. 500-570mm, 1mW (applied to ds3608)
2. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 56, dated May 08, 2019 and IEC/EN 60825-1:2014.

LED
Risk Group classified according to IEC 62471:2006 and EN 62471:2008.

• SE5800 Pulse Duration: 6 ms
• Exempt Group RG0

Marking and European Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU and 2011/65/EU.The full text of the EU Declaration of Conformity is available
at: zebra.com/doc.

• EU Importer: Zebra Technologies B.V
• Address: Mercurius 12, 8448 GX Heerenveen, Netherlands

Waste Electrical and Electronic Equipment (WEEE)
For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: zebra.com/weee.

United States and Canada RegulatoryRadio
Frequency Interference Notices
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements – Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-003
B/NMB-003 B
This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range.
This table was created to comply with China RoHS requirements.

This table was created to comply with China RoHS requirements.

| DS3608
---|---
Unit| Restricted substances and its chemical symbols
(Pb)| (Hg)| (Cd)| (Cr+6)| (PBB)| (PBDE)
| —| O| O| O| O| O
| —| O| O| O| O| O
| O| O| O| O| O| O
| O| O| O| O| O| O
| —| O| O| O| O| O
| O| O| O| O| O| O
Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3: The “ − ” indicates that the restricted substance corresponds to the exemption.

United Kingdom
Statement of Compliance
Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity.

• The full text of the UK Declaration of Conformity is available at: zebra.com/doc.
• UK Importer: Zebra Technologies Europe Limited
• Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF

Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.

Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your applications. If you have a problem running your unit or using your equipment, contact your facility’s Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com/support.

• For the latest version of the guide go to: zebra.com\support.

Software Support

Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, go to zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support > Software Downloads. If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:

• Model number
• Serial number
• Proof of purchase
•  Title of the software download you are requesting.

If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software.

Product Support Information

• For information on using this product, see the User Guide at zebra.com/ds36x8-xr.
• To find quick answers to known product behaviors, access our knowledge articles at supportcommunity.zebra.com/s/knowledge-base.
• Ask your questions in our Support community at supportcommunity.zebra.com.
• Download product manuals, drivers, software, and view how-to videos at zebra.com/support.
• To request a repair for your product, go to zebra.com/repair.

Patent Information
To view Zebra patents, go to ip.zebra.com.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
www.zebra.com
© 2024 ZIH Corp and/or its affiliates. All rights reserved. ZEBRA and the stylized Zebra head are trademarks of ZIH Corp, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners.
MN002257A04EN Revision A- May 2024

References

• Zebra Support Community
• Zebra Support Community

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>