MobilitySound SMART-PTT Device User Manual

MobilitySound SMART-PTT Device

SMART-PTT Specification

• Volume – iOS: Channel, Android: PTT
• Power
• Volume +
• PTT – iOS: Channel+, Android: PTT

User’s Manual
To pair your SMART-PTT with your phone (iPhone or Android), Please follow these steps:

1. Power on your SMART-PTT by pressing the PTT button for 10 seconds until the LED flashes twice. This will reset the device to the factory default settings.

2. Open the Zello app and add PTT as the first step. This is crucial.

3. If you are using an iPhone, it will prompt you to pair with PTT-Mxxx. Click “YES” twice.

4. If the pairing request doesn’t show up on your Android phone, go to Settings, disable, and enable Bluetooth
   to trigger the pairing process. If needed, tap on PTT-Mxxx to ensure it is connected to your phone.

5. Your SMART-PTT is now ready to use.

Federal Communication Commission Interference Statement
To reduce the risk of interference, please consider the following:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact with the transmitting antenna during transmission.

SMART-PTT Specification

Specification

• Bluetooth low energy mode v4.0
• ARM Cortex – M0 32-bit processor
• AES HW encryption
• Replaceable CR2032 battery for 1 year lifetime.
• 5 Buttons for PTT, iOS Channel+/-, Vol+, Vol-
• LED for power on indication.
• Firmware upgradeable DFU by air.

User’s Manual
To pair your SMART-PTT with the phone(iPhone or Android), please follow these steps:

1. Power on SMART-PTT. Press the PTT button for 10s until the LED flashes twice. It’s reset to factory default.
2. Go to Zello to add PTT first. ( It’s most important)
3. iPhone will ask PTT-Mxxx to pair, click “YES” twice.
4. If the pairing request doesn’t show up on an Android phone, go to Settings then disable and enable Bluetooth to trigger the pairing process, if necessary, tap on PTT-Mxxx to make sure it is connected to the phone.
5.  It’s ready to go.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please
avoid direct contact to the transmitting antenna during transmitting FCC ID XTS-SMART-PTT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>