Berger 359820 LED Camping TV with BT User Manual

LED Camping TV mit BT
User Manual

Air circulation and high temperatures:

The ventilation slots on the back of the unit must always remain free. Please do not place newspapers or blankets on or over the TV set. If the TV set is placed in a cupboard or on a shelf, make sure that there is at least 2 cm of free space at the top and sides for air circulation. Like any electronic device, your TV set requires air for cooling when it is in operation. If the air circulation is obstructed, this may cause a fire. Only place the TV set with the stand on a level, stable, horizontal surface. The front of the TV set should
not protrude, especially when it is installed in or on top of furniture. Set up the TV set in such a way that it is not exposed to direct sunlight or any additional is exposed to heat
from radiators. Avoid metal parts, needles, paper clips, liquids, wax, or similar objects getting insidethe device through the ventilation slots in the rear panel. This will cause short
circuits in the device and may result in a fire. If anything does get inside the machine, unplug the machine immediately and contact your service representative to check.

Repairs and accessories:
Never remove the rear panel of the TV set yourself. Only allow authorized TV technicians to perform repair and service work.
Cleaning:
Clean the TV set, the display, and the remote control only with a damp, soft and clean cloth without any abrasive or harsh cleaning agents.
Note on the LED display:
The TV set with the LED display that you have purchased meets the highest quality standards and has been checked for pixel errors. Despite the utmost care in the manufacture of the displays, it cannot be 100% ruled out for technological reasons that pixels may have defects.

SCOPE OF SUPPLY

1.  LED TV set
2. 230-volt power supply
3. remote control
4. operating instructions
5. Stand

POSITION AND FUNCTION OF THE CONTROL BUTTONS
FB19BT2, FB22BT2, FB24BT2 and FB27BT2

Media, AV, PC, YPbPr and HDMI
• Opening or exiting a mene
2| CH+ / –| • Selecting the TV channels, press this key to select the channels or to select the upper or lower menu in the OSD menu
3| VOL+ / –| • Increase or decrease the volume
• Adjusting the selected menu items in the OSD mene
4| ****| • Power button in standby mode

The on/off switch is located at the back next to the control buttons.

CONNECTIONS

REMOTE CONTROL

Inserting the batteries
Replace the batteries as shown in the figure: 2 batteries type ” AAA” is required.

Attention:

1. Store batteries in a childproof place.
2. Never try to charge alkaline batteries, do not short-circuit them or throw them into a fire.
3. Always replace both batteries simultaneously. Do not mix old and new batteries or batteries of different types.
4. If you do not use the remote control for a long time, remove the batteries to prevent acid leakage.

Notes:

1. Do not drop or step on the remote control.
2. Protect the remote control from water and moisture.
3. Do not use the remote control for other devices at the same time.
4. If the television does not respond to the signals from the remote control, replace the batter I e s fi r s t!

START-UP

Before putting your TV set into operation, please connect it to a suitable power supply. For your convenience, we have already installed a channel list for DVB-S2 reception at the factory. There- fore, you do not have to perform a channel search. For DVB-T/C reception, we recommend that you perform an automatic channel scan depending on your location. To do this, go to the main menu „Channel search“ and select the item „Automatic channel search“, select DVB-T or DVBC and follow the instructions.

Selecting a TV channel
Either use the CH+/- key and the arrow key to switch up or down a channel or the 0-9 key to call up a channel directly.
Note: You can return to the previously selected channel at any time by pressing the RECALL key.
Edit Channels
Here you can move and delete the channels found within your programme positions. You also have the option of creating your own favourites list. To do this, select the desired channel with the arrow keys and press the FAV key on the remote control to mark it.
Teletext
In DVB-S/S2, DVB-T, DVB-C: Press the TEXT key to open and close Teletext.
EPG (Electronic Programme Guide)
Press the EPG key to open the electronic programme guide. Use the arrow keys to navigate through the TV programme and view more information about the respective programme.
Selecting the input source
Press the Source key on the TV or your remote control, select the desired input source and confi rm with „Enter“.

AUTOMATIC STATION SEARCH WITH INITIAL INSTALLATION

In the „Options“ menu, select the line Initial installation and confirm with entering.
Confi rm this menu again with entering.

Confi rm with entering and selecting the line „Search“ in the following picture and confirm.

PICTURE MENU

Press the MENU key to display the main menu. Then use the arrow keys to select „Picture“ in the main menu. You can choose from four different picture modes. Please note that only the „Personal“ mode can be changed.

SOUND MENU

You can choose from five different sound modes here. Please note that only the „Personal“ mode can be changed. You can also activate or deactivate the Bluetooth function here.

TIME MENU

The TIME submenu displays the following menu items: CLOCK, TIME ZONE, POWER ON and OSD TIMER. Here you can set the automatic switch-off and switch-on time. You can also set the sleep timer and the display duration of the OSD menu.

PROTECTION MENU

In this menu, you can activate the protection for minors. After selecting the menu with the down arrow key, you will be asked for the factory-set password. Enter the default password: 0000. To change this, select the menu item Set password. Now you can enter a new password (use a numeric keypad) and confirm it in the 2nd line.

SETUP MENU

In the SETUP menu, you can set the menu language, the display and the deaf aid. The unit can be reset to the basic settings under the item „Factory settings“.
CI+ Information
Here you can find information about the CI+ module.
5 V active antenna for DVB-T reception
Switch it on under the menu item CHANNEL in the main menu.

MEDIA MENU (USB CONNECTION)

The USB connection is located on the side of the TV set (see pages 6-8). First, insert your USB stick into the USB port. Then press the SOURCE key on the remote control. The connection menu appears on the screen and here you now select the item Media. The data stored on the USB stick will now be loaded automatically. In the menu, select between the individual categories Photo, Music, Movie and Text.

PVR RECORDING (OPTIONAL)

You can record to external memory. Please note that not all USB sticks or external hard disks are compatible. USB 3.0 storage media in particular can cause problems. Due to a large number of models and memory sizes, we cannot guarantee that all USB memory devices available on the market are fully functional. Above all, a speed of more than 5MB/s is important. You can start the recording as a timer recording in the EPG menu or as an instant recording by pressing the „Media2“ key on the remote control. The recording is saved in the Media menu under „Film“. You can access this menu via the Source function on the remote control. You can start Timeshift by pressing the „D.Prog“ key on the remote control. Press the „Stop“ key to return to the live picture. Timeshift is controlled via the function keys displayed in the TV picture.

OPERATING MANUAL FOR FAST SCAN

1. Press the MENU key.

2. Select NORMAL SCAN and press ENTER.
   

3. Press the key to select Fast Scan.

4. Press ENTER.

5. Select the provider with a key to open the list of countries.

6. Move the cursor down to highlight SCAN and press ENTER.

7.  Confirm with the YES button.
   ‘

8. Download starts after 5s.
   

9. When the download is finished, the first channel on the list is displayed.

AUTOMATIC SEARCH WITH NEW / OTHER SATELLITES

Select the main menu. Select automatic search and press ENTER to enter the submenu.
Press ENTER again.
Satellite: Use the buttons to select the desired satellite.

Channel Type: Use the keys to select whether you want to receive „All“ channels or only „Free“ or only „Scrambled“ channels.
Service Type: Use the keys to select whether you want to search for and save radio, TV or all channels.
Search Mode: Press the key to select the search mode (Preset, Auto, Blind Scan). Normally it is a Blind Scan.
Preset loads the preset station list from the factory. Use the keys to select the menu item „Search“ and press the „ENTER“ key to start the search.

DVB-T2 SEARCH

Channel search for DVB-T / T2 and DVB-C (recommended procedure also for countries such as the Czech Republic, Slovenia, etc.) Key Source, change to Antenna
Before a search in DVB-T / T2 mode, you should switch on the 5V antenna voltage in the main menu. Most antennas require this setting. It is recommended to select the setting OFF in the line LCN. LCN means automatic pre-sorting, but it does not work in Germany, so it is recommended to re-sort manually.

Select DTV and Germany with the right arrow key.
Depending on the region, the channel search results in over 60 channels.
Private channels are usually displayed first, but these require the Freenet module for decoding. Please place free channels in the first pJaces using the „Edit channels“ function.

DVB-S MANUAL SEARCH

WITH DISPLAY OF QUALITY AND SIGNAL
Here you can check the alignment of the SAT antenna via the level display.

TROUBLESHOOTING

Please use the list below to try to correct the most common errors before contacting customer service. A minor adjustment can often solve the problem and restore your screen
reception.

• Adjust the brightness and contrast.
• Check the input signal.
• Check the connection between the monitor and the machine. Unplug the power cord, wait one minute and then reconnect the unit.
• Check the screen selection.
The picture is not clear| • Check that the video input cable is plugged in correctly.
Colours are blurred| • Possible power fluctuations, connect the unit to another power source.
• Check whether there are magnetic devices in the immediate vicinity (wireless receiver, AC transformer, etc.).
Picture “wobbles” or| • Check that the video input cable is plugged in correctly.
No sound| • Check the video input voltage range (V-sync Max. 75Hz, H-sync Max.48.08KHz)
• Make sure that the video cables are connected correctly.
The remote control does not| • Check the connection to the speaker.
• The sound may be off (mute), try adjusting the volume.
Poor picture reception| • Check whether the remote control signal is blocked by an object or light.
• Check the batteries and replace them with new ones if necessary.
and/or poor sound| Check the correct setting of any upstream reception devices (satellite receiver, DVB-T receiver)
If the problem persists.| Unplug the power cord, wait one minute and then reconnect the machine.
Further notes
Power supply| The cable cross-section must be at least 2 x 0.75 mm², for cable lengths of 5 m, at least 2 x 2.5 mm²
Reverse polarity| Make sure that the +/- voltage is correct (note the symbol on the sticker). If the polarity of the unit is reversed, the warranty will become void.

If your television still does not work, please contact your dealer or the technical service department.

TECHNICAL DATA

Power, space and weight saving due to slim design

24
Network| Bluetooth 5.1
Power supply| 100 – 240 V AC oder 12/24 V DC
Dimensions (WxHxD) in cm| 44 x 30 x 14| 50,6 x 33,7 x 17,6| 55,2 x 36 x 17,6| 63,4 x 37,9 x 8,7
Wall bracket connection| VESA 10 x 10 cm
Weight| 2,6 kg| 3,5 kg| 3,7 kg| 3,5 kg
Ambient temperature| -10° C – +45° C
Storage temperature| -20° C – +60° C

Note
Designs, functions and equipment are subject to change. The example pictures used are only suitable for illustrative purposes and may differ from the original.

WARRANTY

Every Berger product is thoroughly checked and tested before it leaves the factory. The legal warranty is two years and begins with the purchase of the device. Please prove this date with the proof of purchase (sales slip, invoice, delivery note, etc.). Please keep these documents in a safe place. If repairs are required, take the unit to your dealer or send it in for repair. This warranty does not apply under the following conditions:
Damage caused by improper use or use in an unsuitable environment.

DISPOSAL

If possible, put the packaging material in the appropriate recycling waste.
Note on environmental protection:
From the date of transposition of European Directives 2012/19/EU into national law, the following applies: Electrical and electronic equipment must not be disposed of with household waste. Consumers are legally obliged to return electrical and electronic equipment at the end of its service life to the public collection points set up for this purpose or to the point of sale. Details are regulated by the respective national law. The symbol on the product, the instructions for use or the packaging refers to these regulations. By recycling, material recovery or other forms of recycling of old devices/batteries, you make an important contribution to the protection of our environment.

EU DECLARATION OF CONFORMITY

(In accordance with EN ISO/IEC 17050-1)

Str. 1,  92318 Neumarkt
Germany

THIS DECLARATION OF CONFORMITY IS ISSUED UNDER THE SOLE RESPONSIBILITY OF:

Name and address of manufacturer:| Fritz Berger GmbHm, Fritz-Berger-Str. 1, 92318 Neumarkt
Germany
---|---
Product identification:| Berger LED Camping TV mit BT 22 Zoll 359800
See appendix A for a list of all products covered by this declaration

THE PRODUCTS MENTIONED IN THIS DECLARATION ARE IN CONFORMITY WITH:

EU Community Legislation| Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU [OJEU L174/88-110, 01.07.2011] Ecodesign energy-related products Directive 2009/125/EC [OJEU L285/10-35, 31.10.2009] Radio Equipment Directive (RED) 2014/53/EU [OJEU L153/62-106, 22.05.2014]
---|---
Harmonised standards| Safety of electrical equipment EN 62368-1:2014 + A11:2017
Radio equipment ETSI EN 300 328 V2.2.2; ETSI EN 301 489-1 V2.2.3; ETSI EN 303 372 V1.1.1
Exposure of humans to electromagnetic fields (EMF) EN 62311:2008
Electromagnetic Compatibility (EMC) ETSI EN 301 489-1 V2.2.3; ETSI EN 301 489-17 V3.2.4
EN 55032:2015+A11:2020; EN 55035:2017; EN IEC 61000-3-2:2014; EN 61000-3-3:2013
Restricted substances in electrical products EN IEC 63000:2018
Ecodesign
Regulation (EC) No 642/2009 – Ecodesign televisions, Regulation (EU) 801/2013 – Ecodesign Networked Equipment, Televisions, Coffeemakers,  Regulation (EU) 2019/2021 – Ecodesign displays

Other specifications:
Notified Body:
Additional information:

Place and date of issue:   Neumarkt, 16 February 2022

Signature:

Fritz Berger GmbH
Fritz-Berger-Str. 1
92318 Neumarkt, Germany
Tel. (+49) 91 81 – 330 100
Fax (+49) 91 81 – 330 500
Nr. 359320 / 359800 / 359810 / 359820
PC: 201028422/01
E-Mail:service@fritz-berger.de
Web: www.fritz-berger.de

References

• Global consulting | Roland Berger
• Fritz Berger – Spezialist für Campingzubehör und Freizeit - Fritz Berger Campingbedarf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>