VIKING K-1900-8 Series Hot-Line Panel Phone with Keypad User Manual
- June 6, 2024
- VIKING
Table of Contents
VIKING K-1900-8 Series Hot-Line Panel Phone with Keypad User Manual
The K-1900-8 Series panel phone can either auto-dial a phone number each time the handset is lifted, be used as a multi-number auto-dialer, or be used as a standard (dumb) phone. The unit will touch tone or pulse dial and will not auto-dial on incoming calls.
The K-1900-8 Series housing consists of a heavy gauge stainless steel panel, metal touch tone keypad, armored cable, heavy duty handset, and all metal cradle. The K-1900-8 Series can be easily touch tone programmed at the shop or installation site. All programming is stored in non-volatile memory.
The K-1900-812L and K-1900-812L-EWP feature a 12″ long armored cable with an internal stainless steel lanyard for additional cable strength.
The K-1900-8-EWP and K-1900-812L-EWP share all the features of the K-1900-8 and K-1900-812L in addition to Enhanced Weather Protection (EWP) for outdoor installations where the unit is exposed to precipitation or condensation. EWP products are designed to meet IP66 standards and may feature foam rubber gaskets, sealed connections, gel-filled butt connectors, as well as potted circuit boards with internally sealed, field-adjustable trim pots and DIP switches for easy on-site programming. For more information on EWP, see DOD 859.
Note: If a ringer is required, use an external unit such as the Viking SR-1 (DOD 477), or LPR-1 (DOD 550).
Features
- Vandal Resistant Features: 12 gauge (0.105″ thick) 316 stainless steel panel with permanent laser etched graphics, armored cable, metal cradle, heavy-duty metal keypad, and hex drive mounting screws
- Weather Resistant Features: Marine grade 316 stainless steel faceplate and screws, and internally sealed keypad
- Auto dials one programmable speed dial number (up to 32 digits)
- Multi-number dialer mode adds 5 speed dial numbers (up to 16 digits)
- Touch tone or pulse dialing
- Non-volatile memory (no batteries required)
- Operates on analog PABX and key system extensions or analog Centrex and CO lines
- Programmable 6 digit security code
- Touch tone programmable
- Optional Enhanced Weather Protection (EWP) available – EWP products are designed to meet IP66 Ingress Protection Rating, see DOD 859
- 12″ armored handset cable on K-1900-812L and K-1900-812L-EWP
- 36″ armored handset cable on K-1900-8 · 54″ armored handset cable on K-1900-8-EWP
- Programmable pre-dial pause
- Blocks fraudulent calls from hand held pocket dialers
- Limited toll Restriction in dumb phone mode
- Hearing aid compatible amplified handset with sealed push button volume control
- Programmable default volume level
- Programmable volume control disable
- Flush mount with included steel rough-in box, or use an optional VE-5×10 surface mount box (not included, see DOD 424)
www.VikingElectronics.com
Information: 715-386-8861
Applications
- Catalog sales
- Kiosks
- Courtesy and customer service phones
- Automated tellers (ATM’s)
- Hot-line reservation phones
- Security and emergency phones
- Replaces leased ringdown circuits
- Gate/entrance communication in noisy locations (diesel trucks, factory noise, etc.)
Specifications
Power : Telephone line powered (20V DC/18mA minimum)
Dimensions for Standard Model
Phone : 5.0″ x 10.0″ x 4.54″ (127mm x 254mm x 113mm)
With rough-in box : 5.0″ x 10.0″ x 5.53″ (127mm x 254mm x 141mm)
Dimensions for EWP Model
Phone : 5.0″ x 10.0″ x 4.93″ (127mm x 254mm x 125mm)
With rough-in box : 5.0″ x 10.0″ x 5.61″ (127mm x 254mm x 143mm)
Shipping Weight : 5 lbs (2.3 kg )
Operating Temperature : -30°F to 140°F (-34°C to 60°C)
Humidity – Standard Model : 5% to 95% non-condensing
Humidity – EWP Model : Up to 100% condensing
K-1900-812L(EWP) Handset Cable Length : 12″ to 12.7″ (31 cm to 33 cm)
K-1900-8 Handset Cable Length : 34″ to 37″ (86 cm to 94 cm)
K-1900-8-EWP Handset Cable Length : 52″ to 57″ (132 cm to 145 cm)
Touch Tone Dial Speed : Normal = 120ms on/off, Fast = 50ms on/off
Pulse Dial Speed : Normal = 10 pps, Fast = 20 pps
Connections : (2) gel-filled butt connectors
Installation
To install the K-1900-8 panel phone, attach the panel using the provided screws or use the optional VE-5×10 weather resistant surface mount box. Note: Four extra screws and nuts are provided to fill the unused mounting holes. The optional VE-5×10 surface mount box (shown below) is designed to be surface mounted to a wall, post, single gang box or a VE-GNP or VE-GNP-2 goose neck pedestal (shown right). The K-1900-8 can also be mounted in an optional VE-9×20 Weatherproof Enclosure (DOD 413). Note: When mounting a K-1900-8-EWP in a VE-9×20, the length of the handset cable must be reduced. Use a 3/32″ hex key or bit to loosen the set screw in the brass handset cable retainer. Pull approximately 18 inches of the cable through the panel and retighten the set screw.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
Programming
Operation
A. Single Number Auto Dialer
In the single number auto dialer mode (see Programming section D), when the
K-1900-8 is taken off-hook it will speed dial the phone number programmed in
memory location #00. After speed dialing is complete, the keypad is available
for user Touch Tone signaling. In this mode, the K-1900-8 can be programmed to
block hand held dialers (see Programming section F).
B. Standard (Dumb) Phone Mode
If nothing is programmed in memory locations #00, the K-1900-8 drops into the
dumb phone mode. The phone will act like any standard 2500 type telephone. The
only feature which may be enabled is the limited toll restriction (see
Programming section I).
C. Multi-Number Auto Dialer
In the multi-number auto dialer mode (see Programming section D), when the
K-1900-8 is taken off-hook it will dial one of six speed dial numbers
programmed in memory locations #01, #02, #03, #04, #05 and #00 when the user
presses 1, 2, 3, 4, 5, or 0 (respectively) on the keypad. After speed dialing
is complete, the keypad is available for user Touch Tone signaling. In this
mode, the K-1900-8 can be programmed to block hand held pocket dialers (see
Programming section F).
D. Handset Receiver Volume Adjustment
The K-1900-8 has a sealed push button switch located on the inside handle of
the handset. Each push of the button will rotate through the receiver volume
levels if enabled. After four actuations, the receiver volume is back to its
default setting. Hanging up the phone will automatically set the receiver
volume to its default setting.
Warranty
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, CONTACT: VIKING TECHNICAL SUPPORT AT715-386-8666
Our Technical Support Department is available for assistance Monday through Friday 8am – 5pm central time. So that we can give you better service, before you call please:
- Know the model number, the serial number and what software version you have (see serial label).
- Have your Product Manual in front of you.
- It is best if you are on site.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
- Customer must contact Viking’s Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA) number. The customer MUST have a complete description of the problem, with all pertinent information regarding the defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
- Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
- Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
- RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
- Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The customer MUST be able to step through recommended tests for diagnosis.
- If the Technical Support Product Specialist determines that the equipment is defective based on the customer’s input and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14) calendar days from the date of issue.
- After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your distributor will then replace the Viking product using the same R.A. number.
- The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven’t followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
TWO YEAR LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of two years from the date of purchase from any authorized Viking distributor. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking’s Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others. This warranty does not cover non-EWP products that have been exposed to wet or corrosive environments. This warranty does not cover stainless steel surfaces that have not been properly maintained.
NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING’S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED AS SUCH.
FCC REQUIREMENTS
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN’s on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of the REN’s should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as determined by the total REN’s, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this K1900-8 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If the K-1900-8 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the K-1900-8, for repair or warranty
information, please contact:
Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016
715-386-8666
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY
NUMBERS :
Remain on the line and briefly explain to the dispatcher the reason for the
call. Perform such activities in the off-peak hours, such as early morning or
late evenings.
It is recommended that the customer install an AC surge arrester in the AC
outlet to which this device is connected. This is to avoid damaging the
equipment caused by local lightning strikes and other electrical surges.
PART 15 LIMITATIONS
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
4 DOD 362
Printed in the U.S.A.
ZF301770 Rev F
Documents / Resources
|
VIKING K-1900-8 Series Hot-Line Panel Phone with
Keypad
[pdf] User Manual
VIKING, K-1900-8 Series, Hot-Line, Panel, Phone, Keypad
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>