MAXIM 88830 Series Solid Wood Blade Fan with LED Light Kit User Manual

88830 Series Solid Wood Blade Fan with LED Light Kit

Specifications:

• Model Number: 88831/88833/88834

• Product Name: WOODWIND 52/72/80 Solid Wood Blade Fan w LED
  Light Kit

• Blade Material: Solid Wood

• Fan Sizes: 52 inches, 72 inches, 80 inches

• LED Light Kit: Included

• Power Consumption: 35W

• Warranty: 5 Years

Product Usage Instructions:

Safety Precautions:

Before installation, ensure the building structure and appliance
installation do not expose combustible material. Do not install the
fan in a ceiling with a combustible finish. Avoid leaving wood,
rafters, or thermal insulation exposed. Disconnect the fan from the
power supply before installation, cleaning, or servicing.

Battery Usage:

Use CR2032 3V batteries and ensure correct polarity. Do not mix
old and new batteries or different types. Secure the battery
compartment properly. Dispose of batteries according to local
regulations.

Installation:

1. Wood Ceiling: Drill the mounting bracket
   directly into the wood ceiling with wood screws or use tools to fix
   it tightly.

2. Concrete Ceiling: Drill a hole with an 8mm
   hammer drill bit, then fix the bracket using the expansion screws
   provided.

3. Hanger Bracket: Install the hanger bracket to
   the outlet box by removing and replacing the screws.

Electrical Wiring:

Follow NFPA 70-1999 and local codes. Connect the appropriate
conductors as instructed. Ensure proper grounding and consult a
qualified electrician if needed.

Mounting:

Mount the fan securely to a structural framing member or an
outlet box rated for fan support. Check the outlet box’s stability
before installation.

FAQ:

Q: Can I use rechargeable batteries with the fan?

A: No, non-rechargeable batteries should be used with the fan to
prevent any risk of injury or damage.

Q: How do I clean the fan blades?

A: When cleaning the fan, ensure it is disconnected from the
power supply. Use a soft, damp cloth to gently wipe the blades. Do
not insert foreign objects between the rotating blades.

Item/Model Num:88831/88833/88834 WOODWIND 52″/72″/80″ Solid Wood Blade Fan w LED Light Kit
1

SAFETY PRECAUTION

· WARNING -To make sure power is off before attempting installation.

· WARNING -Support Directly From Building Structure. When mounted directly to

the building structure, appliance installation shall not expose combustible material

and do not install the appliance to a ceiling with combustible finish. The installation

of the appliance cannot leave the wood of the rafters or any thermal insulation

exposed to the interior of the room.

· WARNING -To reduce the risk of fire, electric shock , or injur y to persons, unplug or

disconnect the appliance from the power supply before the fan installation, cleaning,

or servicing.

· WARNING -To Reduce The Risk Of Fire Or Electric Shock , Do Not Use This Fan With

Any Solid-State Speed Control Device.

· WARNING -To Reduce The Risk Of Personal injur y, Do Not Bend The Blade Brackets

When installing The Brackets, Balancing The Blades, Or Cleaning The fan. Do Not

Insert Foreign Objects In Between Rotating Fan Blades.

· WARNING -Remove and immediately recycle or dispose of batteries from

equipment not used for an extended period of time according to local regulations. Do

NOT dispose of batteries in household trash or incinerate. Even used batteries may

cause severe injury or death. Call a local poison control center for treatment

information, Non-rechargeable batteries are not to be recharged. Don not force

discharge, recharge, disassemble, heat above 125°C or incinerate. Doing so may

result in injury due to venting, leakage or explosion resulting in chemical burns.

Ensure the batteries(CR2032 3V) are installed correctly according to polarity(+ and-).

Do not mix old and new batteries, different brands or types of batteries, such as

alkaline, carbon-zinc,or rechargeable batteries. Always completely secure the battery

compartment. lf the batter y compartment does not close securely, stop using the

product, remove the batteries, and keep them away from children.

· Remove and immediately recycle or dispose of batteries from equipment not used

for an extended period of time a ccording to local regulations.

· The installation is to be in accordance with the National Electrical Code , ANSI/

NFPA 70-1999 and local codes. Consult a qualified electrician if in double.

· WARNING -To Reduce The Risk Of Electric Shock , This Fan Must Be installed With A

General-Use,lsolating Wall control/Switch.

· All set screws must be checked, and re-tightened where necessary before

installation.

· After making the wire connections, the wires should be spread apart with the

grounded conductor and the equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the other side of the outlet box.

· The splices after being made should be turned upward and pushed carefully up into

the outlet box.

· Conductor of a fan identified as grounded conductor to be connected to a

grounded conductor of power supply, conductor of fan identified as ungrounded

conductor to be connected to an ungrounded conductor of power supply, conductor

of fan identified for equipment grounding to be connected to an equipment-

grounding conductor.

· CAUTION -To Reduce The Risk Of Electric Shock , Disconnect The Electrical Supply

Circuit To The Fan Before Installing Light Kit.

· WARNING -To reduce the risk of fire, electric shock , or personal injur y, mount

directly to a

structural framing member of to an outlet box marked (acceptable for fan support of

15.9 kg(35lbs) or less). For outlet box mounting, use mounting screws provided with

the outlet box. Must check that the outlet box is securely installed in place before

install.

2

35 W
9 Warranty: 5 Years
3

1*Canopy cover
1. Wood ceiling: Drill the mounting bracket directly into the wood ceiling with wood screws (4 pieces) or Use tools to fix the mounting bracket tightly. (The ceiling must bear more than 60KG)
2. Concrete ceiling: First use an 8mm hammer drill bit to drill the hole according to the length of the expansion screw, then use the equipped expansion screws(2 Pieces) to fix the bracket on the ceiling, and then tighten the nut of the expansion screw.
4

3. Install the hanger bracket to the outlet box a. Take off the screws on the outlet box. b. Install the hanger bracket to the outlet box by screws

Note: 1). According to the ceiling of different materials, use different screws to fix
the mounting bracket (as shown above). 2). After the bracket is fixed, it must be determined to beable to bear the
weight of more than 60 kg(test pull by hand) for safety. 3). Ceiling fans cannot be installed on gypsum ceilings. 4). To reduce the risk of fire, electric shock , or personal injur y mount to an
outlet box marked”Acceptable for Fan Support”.Use the mounting screws provided with the outlet box. Most outlet boxes commonly used for supporting lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

1. Select the downrod a. There are two downrods of 4 inch and 6 inch in the package, customers can choose according to the height of the house. b. The normal default is to install the 4 inch downrod. c. How to replace the 6 inch downrod:

1

2

3

4

5

4″

4″

4″

4″

6″

5

2. How to install Suspension Installation .Remove the positioning screws from the fan body as follows and place them
side by side to proceed to the next step (Figure 6) .Get off the pin off the downrod by remove the R clip, and get the lead wire
through the downrod and canopy, then seat the downrod into the fan body & rotate the downrod until the holes on the downrod will match with the holes on the fan body, finally, you should get the pin through the holes and fix the pin by the R clip in another side (Figure 7) .Tighten the two set screws removed previously.

6

7

8

Canopy cover
Coupling cover

R Clip

Set Screw

pin

6

1. Remove the three fixing screws from the lamp holder.(Figure 12 ) 2. Please plug the 2 light wires to the LED board properly, and check whether
the driver output wires and the LED source board are tightly inserted, lock the lamp plate to the lamp holder with screws.(Figure 13) 3. Install the lamp shade in place and rotate the lamp shade clockwise. (Figure 14)
7

14 15

Green/Yellow Green/Yellow TO LED LIGHT KIT
TO MOTOR

Antenna

8

Wiring Method: One Live One Neutral
Use Effect:
1.If a regular single pole switch is connected, it can only control to turn on or off the light, but not control the fan. The fan must be turn on/off and adjust by remote control.
2.If the regular single pole switch is not connected, the remote control can directly control the lights and fans separately
Note: This Ceiling fan bulit in light status memory function. When the power is turned off and turned on again, the light will back to the last status. If the light is turn off by remote control, the light will keep the turn off mode. Need use remote control to turn on the light after the power switch on. If the light is turn on before the power switch off , the light will remember the turn on status, the light will keep turn on once switch on.

1.Connect the ground wire from ceiling to three green/yellow wires from the mounting bracket, the hanger ball on the downrod, and the receiver (AC IN E).
2.Connect the neutral wire from ceiling to receiver white wire (AC IN N). 3.Connect the live wire from ceiling to receiver black wire (AC IN L). 4.Plug in the light wires and motor wires in the correct way as indicated in the
diagram. Note: The slotted side of the plug face the slotted side of the socket.
(Figure 16)
16
XI.Balance adjustment method of ceiling fan. If there is any wobble after ceiling fan installation, please confirm whether the screws that fix the hanger ball, mounting bracket, hanger, blade holder, and blade are locked. If one of the above parts is not locked, please re-lock it. If it is locked, please adjust it as follows.
1. Change the position of the fan blades: a. There is no improvement after the swap blades position. Please remove the fan blades 2 and 3 and re-lock each other to observe the effect.
9

18 Balance piece
17
2. Adjust with balance kit. a. Take out the balance bag from the package box, use a balance clamp to select
one of the fan blades and clamp the balance clamp on the edge of the tail end of the fan blade (Figure 18) b. Turn on the fan switch to see whether the wobble of the ceiling fan has been reduced. If it does not improve, try another fan blade. Experiment with all the fan blades in turn to find the blade with the weakest clamping balance. c. Clamp the balance clamp on the fan blade with the weakest wobble, move it in or out on the edge of the fan blade, turn on the ceiling fan to find the best position of the balance clamp to control the wobble balance (Figure 18) d. Take the balance sticker, tear off the double-sided tape of the balance sticker, and stick the balance sticker on the center of the blade at the position of the balance clip (Figure 18)
10

Xlll.Ceiling Fan Troubleshooting Solutions & Common Problems

Fan wobble

3. Check whether the screw of the blade retracted to the motor is locked
4.Can it be installed on the inclined ceiling? Yes, pay attention to the inclination angle not exceeding 15 degrees(pay attention to whether the hanger ball will press the fan receiver)

WARNING / AVERTISSEMENT
· INGESTION HAZARD: This product contains a button cell or coin battery. (CR2032 3V) · DEATH or serious injury can occur if ingested. · A swallowed button cell or coin battery can cause Internal Chemical Burns in as
little as 2 hours · KEEP new and used batteries OUT OF REACH OF CHILDREN · Seek immediate medical attention if a battery is suspected to be swallowed or
inserted inside any part of the body. · DANGER D’INGESTlON: Ce produit contient une pile bouton ou une pile monnaie. · Si ingéré, il peut entraÎner LA MORT ou des blessures graves. · Avaler une pile bouton ou une pile à monnaie peut provoquer des BrÛlures
Chimiques Internes en 2 heures. · GARDEZ les piles neuves et usagées HORS DE PORTÉE DES ENFANTS · Si vous soupÇonnez que la batterie a été avalée ou insérée dans une partie de votre
corps,Consultez immédiatement un médecin.
11

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>