audio-technica AE5100 Cardioid Condenser Instrument Microphone User Manual
- June 6, 2024
- Audio-Technica
Table of Contents
User Manual
Cardioid Condenser Instrument Microphone AE5100
Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly. Please keep this manual for future reference.
Features
- Uncompromising sound quality for overheads, percussion, acoustic guitar, strings, and other acoustic instruments
- Large-diaphragm capsule delivers an accurate and natural response
- Low-profile design permits innovative placement options previously unattainable with a large-diaphragm condenser
- Robust design for enduring dependability on the road
- Integral 80 Hz HPF switch and 10 dB pad
- Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of the desired sound source
Notes on use
The AE5100 is intended for use in professional applications where remote power is available. It requires 11V to 52V DC phantom power, which may be provided by a mixer or console, or by a separate, in-line source such as the Audio- Technica AT8801 single-channel or CP8506 four-channel phantom power supplies.
Output from the microphone’s XLRM-type connector is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). The output phase is “Pin 2 hot” – positive acoustic pressure produces positive voltage at Pin 2.
An integral 80 Hz hi-pass filter provides easy switching from a flat frequency
response to a low-end roll-off. The roll-off position reduces the microphone’s
sensitivity to popping in close vocal use. It also reduces the pickup of low-
frequency ambient noise (such as traffic, air-handling systems, etc.), room
reverberation, and mechanically-coupled vibrations. The AE5100 includes an
AT8471 isolation clamp to provide secure mounting, versatile positioning, and
effective dampening of unwanted mechanical noise.
Avoid leaving the microphone in the open sun or in areas where temperatures
exceed 43°C for extended periods. Extremely high humidity should also be
avoided.
Safety precaution
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.
Cautions for the product
- Do not subject the product to a strong impact to avoid malfunction.
- Do not disassemble, modify or attempt to repair the product.
- Do not handle the product with wet hands to avoid electric shock or injury.
- Do not store the product under direct sunlight, near heating devices, or in a hot, humid, or dusty place.
Connection procedure
Connect the output terminals of the microphone to a device that has a
microphone input (balanced input) compatible with a phantom power supply. The
output connector is an
XLRM-type with polarity as shown in the figure below.
This product requires 48 V DC phantom power.
Specifications
| Element | Fixed-charge back plate, permanently polarized condenser |
|---|---|
| Polar pattern | Cardioid |
| Frequency response | 20 – 20,000 Hz |
| Low Frequency response | 80 Hz, 12 dB/octave |
| Open circuit sensitivity | -36 dB (15.8 mV) re 1V at 1 Pa |
| Impedance | 150 ohms |
| Maximum input sound level | 148 dB SPL, 1 kHz at 1% T.H.D. |
158 dB SPL, with 10 dB pad (normal)
Noise| 11 dB SPL
Dynamic range (typical)| 137 dB, 1 kHz at Max SPL
Signal-to-noise ratio| 83 dB, 1 kHz at 1 Pa
Phantom power requirements| 11-52 V DC, 3.2 mA typical
Switch| High-pass filter,
10 dB pad (normal)
Weight (less accessories)| 143 g
Dimensions| 148.5 mm long, 26.0 mm maximum diameter
Output connector| Integral 3-pin XLRM-type
Included accessories| AT8471 isolation clamp for 5/8″-27 threaded
stands; 5/8″-27 to 3/8″-16 threaded adapter;
AT8136 windscreen; soft protective pouch
• 1 Pascal = 10 dynes/cm² = 10 microbars = 94 dB SPL
- Typical, A-weighted, using Audio Precision System One.
For product improvement, the product is sublect to modification without notice.
Polar pattern
Frequency response
Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2017 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
05-DEC–2020 Form No.ATGC-L0384-20
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>