MINN KOTA 1810300 Jack Plate Side Mount Adapter Brackets Instruction Manual

**MINN KOTA 1810300 Jack Plate Side Mount Adapter Brackets Instruction Manual

**

THE SIDE MOUNT BRACKETS WILL ONLY WORK WITH COMPATIBLE JACK PLATE DESIGNS AND MAY NOT WORK WITH ALL JACK PLATES. DRILLING HOLES TO ACCEPT THE SIDE MOUNT BRACKETS
MAY VOID YOUR MANUFACTURER’S WARRANTY. MINN KOTA IS NOT RESPONSIBLE FOR DAMAGES THAT MAY RESULT.

NOTE: USE THE SUPPLIED ANTI-SEIZE ON ALL FASTENERS TO PREVENT GALLING OF THE NUT.

THE ADAPTER BRACKET IS DIRECTLY MOUNTED TO EITHER THE PORT OR STARBOARD SIDE OF AN APPROVED JACK PLATE. THE MOUNTING INSTRUCTIONS WILL BE SIMILAR FOR ANY INSTALLATION METHOD. PLEASE REFER TO THE CHART BELOW FOR COMPATIBLE JACK PLATE DESIGNS.

COMPATIBLE JACK PLATES:

MANUFACTURER

| MODEL| OFFSET
---|---|---
TH MARINE| ATLAS HYDRAULIC|

4” THRU 12”

| Z-LOCK MANUAL| 6” THRU 12”
R &R DESIGNS| SLIDEMASTER MANUAL|

6” THRU 12”

NOTE: FOR ALL INSTALLATIONS, IT IS RECOMMENDED THAT ONLY THE ELBOW PORTION OF THE
ADAPTER BRACKET ASSEMBLY BE INSTALLED TO THE JACKPLATE BEFORE ATTACHING THE ARM AND FLAG COMPONENTS TO THE ELBOW.

INSTALLATION : SIDE MOUNT

SLIDEMASTER MANUAL & Z-LOCK MANUAL

1. Remove the mounting bolts located on either the port or starboard side of the jackplate. See photos 2 & 3. NOTE: Where appropriate, support then outboard before removing ANY of the jackplate side mounting bolts. ALL bolts must be re-installed into the jackplate before operating the boat.
2. Remove the external jack plate side bar, if equipped. (Slidemaster only, See photo 2) NOTE: Reuse the inner threaded plate that came with the jack plate.
3. Install the 1/2″ bolts provided going thru the elbow component into the jack plate.
4. Proceed to step 5 below.

NOTE: Some earlier Atlas hydraulic jack plates do not have mounting holes drilled from the factory. Jackplates
without mounting holes will have to be drilled and may require part # 1810210 spacer block kit.

ATLAS HYDRAULIC WITH HOLES:

1. Locate the (2) 1/2″ mounting holes on either the port or starboard side of the jack plate.
   NOTE: Holes may be located under the side decals.

2. Align the holes in the elbow component with the holes in the jack plate.

3. Fasten the elbow component to the jackplate with the hardware and anti-seize provided.

4. Proceed to step 5 below.

ATLAS HYDRAULIC WITHOUT HOLES (REQUIRES PART # 1810210 SPACER BLOCK KIT)
NOTE: Drilling (2) 1/2″ mounting holes is required for this installation. Drilling mounting holes thru the Atlas jack plate WILL NOT void your manufacturer’s warranty.

1. Position the spacer block against the side of the jack plate (port or starboard) and slide towards outboard until it touches the main jack plate support. See photo 1, back side.

2. Mark the (2) mounting holes on the side of the jack plate.

3. Drill (2) 1/2″ holes thru the jack plate. Make sure there is nothing on the inside that could get damaged.

4. Proceed to step 5.(next page)

5. Once the elbow component is positioned as high as possible, tighten and torque the mounting hardware to 50 ft.lbs.
   NOTE: BE SURE TO POSITION THE HEAVY DUTY 5/16″ WASHERS OVER THE SLOTS ON THE INBOARD SIDE OF THE ADAPTER BRACKET.

6. Carefully slide the long c-channel segment of the arm over the elbow column so the internal / external teeth align to the desired angle and assemble the 1/2″ bolts, as shown, to lock it into position. Tighten harware to 50 ft.lbs.

7. Next, slide the flag column into the short c-channel segment of the arm and assemble the 1/2″ bolts, as shown, to lock it into position. Tighten hardware to 50 ft.lbs.
   NOTE: When properly installed, the flag portion of the adapter bracket should be parallel to the transom of the boat. It should also be oriented as close to the transom as possible to minimize the possibility of water spray.
   The adapter bracket joints may be indexed to create the desired orientation. The teeth will not allow the joints to index without first separating the components. To index the joints, slide the components  apart, index to the proper orientation and then re-assembe the joints.

8. Complete the installation by mounting the Talon mounting bracket (included with the Talon) as instructed in the Talon installation manual.

9. Attach the Talon mounting bracket to the adapter plate using the  provided hardware and anti-seize.

10. Slide the Talon down onto the mounting bracket and tighten the (4) vertical adjustment nuts.
    MOUNTING EXAMPLE: STARBOARD SIDE WITH OPTIONAL SPACER BLOCK
    

NOTE: If the boat Is to be rIgged wIth a port and starboard adapter bracket, It may be necessary to remove a factory equIpped e-ladder for proper bracket InstallatIon. due to the wIde varIety of e-ladders, mInn kota Is not responsIble for the re-InstallatIon or re-locatIon of any factory equIpped e-ladder.

When it comes to quality anchoring and docking products. Minn Kota is the brand you can depend on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>