CALIBER HWC401 Smart Outdoor Camera 1080p with Motion Detection User Manual
- June 6, 2024
- CALIBER
Table of Contents
CALIBER HWC401 Smart Outdoor Camera 1080p with Motion Detection User Manual
Warning
For all info on the disposal of items with the Wheelie bin icon, please see:
webshop.caliber.nl/media/forms/wheeliebin.pdf
Buttons And Connections
-
Wi-Fi antenna
Adjustable antenna for wireless connection -
Indication LED
- LED will blink rapidly in BLUE while pairing/reconnecting
- LED will be solid BLUE while ON and connected
-
Camera lens
-
IR LED lights
-
24 IR LED lights for night vision
-
Reset button
To reset to factory settings -
DC input
5V/2A input -
LAN connector
RJ45 connector for optional wired connection -
LAN indication LED
- connected through LAN the LED will blink rapidly while receiving/sending data
- LED will burn solid when no cable is connected
-
Ball joint
Can be fixed and released via the clamping ring.
Mounting instructions
Use the provided screws and plugs (if nessesary) to mount the camera on a wall
or ceiling. Make sure that the wire comes out from behind the backplate using
one of the recesses holes.
Installation Instruction
Warning: Make sure the camera to be within range of the Wi-Fi network to ensure a successful connection between the camera and router.
Wi-Fi Configuration instructions
-
Scan QR code to download and install “Caliber Smart Home”
-
Sign in with cell phone number or email
-
Make sure the device on which the app is installed, is connected to the Wi Fi network on which you want the camera to be too.
Once the camera is plugged in it will be powered ON and the indication LED will flash rapidly. -
Click “+” at the up right corner to select and add the device.
-
The APP will ask if the indication LED is flashing and if the startup tone was heard.
Then click “next step”.
If this is not the case, please reset the camera holding the reset-button for approx. 10 seconds. -
Check if the Wi-Fi network is correct, fill in the corresponding password and confirm.
Note: that the password can only contain letters and numbers, no special characters.
-
The APP then will show an QR code on screen.
-
Hold this screen approx. 20 cm in front of the camera lens, maybe move it around a little, until the LED goes OFF. After (3-5) sec. the LED turns ON again and remains on.
-
then confirm by clicking “I heard the beep.
-
The APP will connect the camera. Please wait patiently till the action is completed.
-
When the camera is successfully added you can give it a personal identification name and can choose which group you’d like it to be in.
Through the APP the camera can be viewed and controlled remotely. Some of the functions are e.g.:
-
* Live View (real time view)- Playback (only if an SD card is installed and the camera is set to record).
- Record and screenshot
(record the live feed or make a screenshot and save it to your mobile device)
Note: controls and functions can vary according to camera type/version and set settings.
Remove device
To remove the camera from the APP and Wi-Fi network:
- Open the APP
- Click the icon in the upper right corner, and then click “Remove Device” button in the list
- When remove the device is successful, the LED will start to blink rapidly. Note: The ‘remove procedure’ will clear the camera’s connection which means: erasing all information about the Wi-Fi network. The camera name and the footage on the SD card should be removed manualy.
CALIBER SMART HOME LIVING IN COMFORT
With ‘Caliber smart home’ products you can be sure Everything is controllable with ONE APR WE chose to partner with Tuya. a platform for smart home products which allows great control: not just camera view but a whole range of possibilities
-
Scheduler
-
Scenario’s
(E.G: lights ON when camera detects movement) -
Combine products
-
Share settings with the whole family.
SPECIFICATIONS
- Image sensor: 1/2.7 inch 1080p CMOS sensor
- Minimum illumination: 0.01Lux/F1.2 (B&W mode)
- Lens/viewing anglef: 3.6mm, F:2.0
- Night vision : 24 IR LED lights + IR Cut filter 30m IR distance
- Compression Format: H.264 Main Profile
- Max.Frame rate: 1-25fps
- Network Protocol: HTTP,DHCP,DNS
- WIFI: WiFi802.11b/g/n Freq range: 2402-2480 Mhz Max e.r.p: <100mW/20dBm
- Storage mode: Local storage (8GB pre-installed) /client storage
- Interface: Pre-installed 8GB Micro SD, support up to 128GB
- Motion detection: Support motion detection
- Power: DC5V/1A
- Power consumption: Rated power: 5,0W Max.
- Working environment: Working Temperature 0°— 55°C
- Camera size: 180mm (L) X 60mm (w)x 60mm (H)
- Installation: Wall or ceiling mounting (screwed)
- Waterresistance: P66 (camera unit only – connectors and adapter for indoor use only)
PRODUCT DESCRIPTION
The camera is a Wi-Fi based item that can work with E.G Amazon Alexa by voice control. You can either control it with Android and iOS based APP by phone, anywhere, at any time. The latest information on this topic you can find online: CALIBER.NL/calibersmarthome
FEATURES
- Works with Amazon Alexa by voice control
- Remote view and control via APP anywhere anytime
- Scene control: works with other smart products
- OTA upgrade supported
We are continuously improving/updating our products and product information. It’s therefore possible that there is a slight difference between the description in this manual to the operation of the product. If something is different or not clear: always check our website for the most current version.
The (app) images and illustrations used are indicative and may vary per device and version
Latest declaration form can be found at: calibereurope.cominlmedia/forms/DeclarationHWC401.pdf
Explore our Growing Number of smart home products
www.calibereurope.com
For all info on the disposal of items with the Wheelie bin icon, please see:
webshop.caliber.nl/media/forms/wheeliebin.pdf
CALIBEREUROPE.COM
CALIBER EUROPE BV
Kortakker 10 4264 AE Veen
The Netherlands