reolink PoE Dome Camera Instruction Manual
- June 6, 2024
- reolink
Table of Contents
Reolink PoE Dome Camera Instruction Manual
What’s in the Box
NOTE: Camera and accessories vary with different camera models that you purchase.
Camera Introduction
Camera Connection Diagram
Before using the camera, please connect your camera as instructed below to finish initial setup.
- Connect the camera to a PoE injector with an Ethernet cable.
- Connect the PoE injector to your router, and then power on the PoE injector.
*You may also connect the camera to a PoE switch or Reolink PoE NVR.
NOTE: The camera should be powered with a 12V DC adapter or a PoE powering device such as PoE injector, PoE switch or Reolink NVR (not included in the package).
Set up the Camera
Download and Launch the Reolink App or Client software, and follow the onscreen instructions to finish initial setup.
- On Smartphone Scan to download the Reolink App.
https://reolink.com/wp-json/reo-v2/app/download
- On PC Download path of the Reolink Client: Go to https://reolink.com > Support > App & Client.
NOTE: If you are connecting the camera to a Reolink PoE NVR, please set up the camera via the NVR interface.
Mount the Camera
Installation Tips
- Do not face the camera towards any light sources.
- Do not point the camera towards a glass window. Or, it may result in poor image performance because of the window glare by infrared LEDs, ambient lights or status lights.
- Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the capture object is the same.
- For better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
- Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
- The camera comes with waterproof design so it can work properly under conditions like rain and snow. However, it doesn’t mean the camera can work underwater.
- Do not install the camera at places where rain and snow may hit the lens directly.
- The camera may work in extreme cold conditions as low as -25°C. Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it outdoors.
To separate mounting plate from the dome camera, hold and press on the camera top and turn anticlockwise.
Drill holes according to the mounting hole template and screw the mounting
plate to the mounting holes on the ceiling.
NOTE: Use the drywall anchors included in the package if needed.
Mount the camera to the mounting plate and turn the camera clockwise to lock it tightly. If the camera is not locked properly, the camera may fall when you turn it anticlockwise to adjust the surveillance angle.
NOTE: Run the cable through the cable notch on the mount base.
Once the camera is installed, you may rotate the camera body manually to adjust the camera’s surveillance angle.
Troubleshooting
Camera Is Not Powering on
If your camera is not powering on, please try the following solutions:
- Make sure your camera is powered on properly. The PoE camera should be powered by a PoE switch/injector, a Reolink NVR or a 12V power adapter.
- If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see if the camera will power on.
- Try again with another Ethernet cable.
If these won’t work, contact Reolink Support https://support.reolink.com/.
Infrared LEDs Stop Working
If the Infrared LEDs on your camera stop working, please try the following
solutions:
- Enable infrared lights on Device Settings page via Reolink App/Client.
- Check if the Day/Night mode is enabled and set up auto infrared lights at night on Live View page via Reolink App/Client.
- Upgrade the firmware of your camera to the latest version.
- Restore the camera to factory settings and check out the infrared light settings again.
If these won’t work, contact Reolink Support https://support.reolink.com/.
Failed to Upgrade Firmware
If you cannot upgrade firmware for the camera, try the following solutions:
- Check out the current camera firmware and see if it is the latest one.
- Make sure that you download the correct firmware from Download Center.
- Make sure that your PC is working on a stable network.
If these won’t work, contact Reolink Support https://support.reolink.com/.
Specifications
Hardware Features
Night Vision: 30 meters (100ft)
Day/Night Mode: Auto switchover
General
Operating Temperature: -10°C to 55°C (14°F to 131°F) Operating Humidity:
10%-90%
Ingress Protection: IP66
For more specifications, visit https://reolink.com/.
Notification of Compliance
FCC Compliance Statement
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. For more information, visit:
https://reolink.com/fcc-compliance-notice/.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation.
Simplified EU Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes. throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink official stores or a Reolink authorized resellers.
Learn more: https://reolink.com/warranty-and-return/.
NOTE: We hope that you enjoy the new purchase. But if you are not satisfied with the product and plan to return, we strongly suggest that you reset the camera to factory default settings and take it out the inserted SD card before returning.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of reach of
children.
End User License Agreement
By using the Product Software that is embedded on the Reolink product, you
agree to the terms of this End User License Agreement (“EULA”) between you and
Reolink. Learn more: https://reolink.com/eula/.
Technical Support
If you need any technical help, please visit our official support site and
contact our support team before returning the products,
https://support.reolink.com.
REOLINK INNOVATION LIMITED
Room B, 4th Floor, Kingsway Commercial Building, 171-173 Lockhart Road, Wan
Chai, Hong Kong
(REP) Product Ident GmbH Hoferstasse 9B, 71636 Ludwigsburg, Germany prodsg@libelleconsulting.com
August 2020
QSG1_A
References
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Offizielle Website: Überwachungskameras/-systeme für Zuhause & Geschäft
- Reolink Offizielle Website: Überwachungskameras/-systeme für Zuhause & Geschäft
- Reolink officiel : caméras de sécurité pour la maison et l’entreprise
- Warranty & Return – Reolink
- Reolink Support - Official Reolink Help Center
- Reolink Support - Official Reolink Help Center
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>