TOPEAK TetraRack M2L Rear Mountain Bike Rack User Manual
- June 6, 2024
- TOPEAK
Table of Contents
TETRARACK M1/M2/M2L
TETRARACK M1 (FRONT FORK)
TETRARACK M2 (SEATSTAYS)
TETRARACK M2L (SEATSTAYS)
- Frame
- Rack Slide rail
- Mounting base
- Velcro straps
- Reflective bracket 5-1 Tail Light Mount
- Allen key 2.5mm x 1
- Side pannier hook
- Strap tensioner
- Rubber pad
- Maximum weight capacity:10 kg / 22 lb ( M1 ),12 kg / 26 lb ( M2 , M2L )
- Wheel size compatibility : 26″ – 29 “( Ml, M2) 27.5” – 29 “( M2L )
- Tire width compatibility : s 2.8″
- Width compatibility : front fork 115-145mm ( M1 ), seatstays 95-125mm ( M2, M2L )
- Max. Belastung: 10 kg (M1), 12 kg (M2, M2L)
- Kompatible Laufradgra0en: 26″ – 29″ ( Ml, M2) 27,5″ – 29″( M2L )
- Kompatible Reifenbreite: s 2,8″
- Kompatible Breiten: Federgabel 115 – 145mm (M1), Sitzstreben 95 – 125mm (M2, M2L )
- Charge Maximal supportee: 10kg / 221b (M1),12kg / 26 lb (M2, M2L )
- taille de roue : compatible 26″ – 29′ ( Ml, M2) 27,5 ” – 29 “( M2L )
- largeur de pneu maximal: 2,8″
- largeur compatible: fourche avant 115 -145mm(M1), hauban 95-125mm (M2, M2L )
Install reflector on TetraRack. (Reflector not included)
Tail Light Mount is used for mounting rear lights with 80mm (center to center) mounting holes on TetraRack.
Tail Light Mount is used for mounting rear lights with 80mm (center to center) mounting holes on TetraRack.
WARNING
The seat stays angle must be over 30 degrees for proper operation.
Not suitable to mount on frames with unique geometries.
TetraRack has a mounting length of 200mm. Seatstays and front forks must not contain any obstacles that prevent mounting TetraRack securely.
seatstay diameter must be larger than 15mm. It is not recommended to mount TetraRack on carbon frames.
Compatible with front fork width within 115-145mm. Ensure not to exceed max weight capacity.
MAX WEIGHT CAPACITY
M1| M2/M2L
(10kg/22lb)| (12Kg/26lb)
Compatible with seatstays width within 95-125mm. Ensure not to exceed max weight capacity.
INSTALLATION
Unscrew 6 bolts of the mounting base.
Adjust the width of the rack to fit bike front forks /
seatstays by spreading supports outward.
NOTE: Clean frame/fork mounting area prior to installing TetraRack.
Take Velcro straps with metal loop and route around front forks / seatstays.
Buckle metal loop into the hook of strap tensioner.
Adjust the strap tensioner hook to the lowest position with a 2.5mm Allen key.
Tighten to secure the mounting base to the bike frame.
Use 2.5 mm Allen key to tighten mounting base and bend slightly.
Do not overtighten the mounting base.
IMPORTANT NOTE:
Tighten all bolts after installation is complete.
If the rack is pushed to the left side, please adjust the left mounting position down.
Align the loading plate fore/aft to ensure it is horizontally level
ANGLE ADJUSTMENT
The proper tire clearance of TetraRack M1 / M2 / M21. must be larger than 20mm. Improper tire clearance may cause damage to TetraRack, your bike, or bodily injury.
FRONT FORK/SEATSTAY
Do not install the rack on screw holes, hose stops, or brake hoses.
When fixing mounting straps, do not inadvertently tighten over brake hose or
derailleur cable
OPTIONAL ACCESSORIES
WARNING NOTES
- Clean frame/fork mounting area prior to installing TetraRack.
- Never exceed maximum loading capacity when using TETRARACK M1 ( 22 lb / 10 kg ) and TETRARACK M2 / M2L ( 26 lb / 12 kg ).
- Check TetraRack after every ride for secure mounting. If there is any exaggerated movement of TetraRack during a ride, stop riding immediately.
- Do not engage in extreme ridings, such as jumping, when using TetraRack
- Do not attempt to use TETRARACK as a passenger seat.
- Always balance the load on TetraRack. Do not install a pannier bag only on one side of TetraRack.
WARRANTY
2-year Warranty: All mechanical components against manufacturer defects only. Warranty Claim Requirements To obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the warranty begins on the date of manufacture. All warranties will be void if the product is damaged due to user crash, abuse, system alteration, modification, or used in any way not intended as described in this manual. * The specifications and design are subject to change without notice. Please contact your Topeak dealer with any questions. For USA customer service, call: 1-800-250-3068 www.topeak.com