SMARTWITNESS 4 Channel HD Recorder CP4S Installation Guide

SMARTWITNESS CP4S 4 Channel HD Recorder Installation Guide

Model #: CP4S-NA, CP4S-EU

v1.0.1

WARNING: SmartWitness installations should be performed by a qualified individual or installation professional only. Working with a vehicle’s power system can be dangerous to both you and your vehicle. This installation is intended only to be a guide since vehicle designs and power/input sources can vary significantly from vehicle to vehicle.

If you need to schedule a professional installation service in the USA for your SmartWitness device(s), please visit https://smartwitness.com/scheduleinstall and submit the online form.

All cellular-enabled CP4S devices must use the installation wizard for proper onboarding and activation, please visithttps://install.smartwitness.com to register, login, and use the SmartInstall wizard.

Overview

The SmartWitness CP4S is the world’s smallest 4 channel LTE-enabled vehicle recorder. CP4S, an in-vehicle drive recorder, offers commercial vehicle owners an effective risk reducing means to aid in the investigation process, decrease collateral damages associated with car accidents, encourage safe driving, monitor driving behaviors, and enhance the overall safety on the road. CP4S features 4 camera inputs for connecting 1, 2, 3, or 4 cameras. A 6-Axis GSensor, Microphone, SD card (up to 256GB capacity), panic button, cellular modem, & GPS receiver are included. CP4S is powered up on vehicle ignition and automatically begins recording. Various camera options are available, making the amount of possible CP4S system combinations nearly endless.

CP4S is small, lightweight, easy to use, and simple to install compared to other complex and expensive mobile DVRs. CP4S can be easily installed inside a glove box or purchased with a locking case to prevent unauthorized access to the recorded data. An LCD monitor is not required for use, but can be added to provide added visibility in and around the vehicle for added security and safer operation.

• Features

• Package Contents

CP4S Hardware Overview

Watch 360° Hardware Overview Video here: https://youtu.be/cLmUPGLnqSM

• Dimensions

• Front View

• Rear View

Installation

Park the vehicle on a flat service. Turn of the engine before installing the CP4S.

• The SD card and SIM is usually pre-inserted, but if it’s not, you should be notified by the service provider and have been provided SIMs/SDs separately.

Find installation location for recorder and locking case (if applicable).

• * The default axis adjustments by device position is set as shown below.

• Install all the interior and exterior cameras with 3M dual sided adhesive or hard mounting screws (confirm with customer as to the desired installation method).

  • All the four cameras will be connected to the CP4S recorder via the Camera Input Cable.

• Install remote control onto dash next to the steering wheel and within reach of the driver.

• Run camera cable(s) and secure in headliner and or other area so no cables are exposed. Use provided wire clips if necessary.

• Connect all cables to CP4S Recorder. Secure the windshield mounted camera cables into the headliner and down the A-Pillar.

• Route the GPS cable and LTE Antenna cable (if applicable) up the side panel and on the dashboard , in view of the windshield (so it can have a view of the sky to acquire GPS signal).

  • Activate the product in an area without large buildings to improve GPS reception.
  • The temperature ranges for optimum operation of the GPS receiver in your car is -10 ~ 50°C.

• Camera Types
  • CP4S has various camera models offered which should be installed in the appropriate location. Here is a reference guide for the common models.

*NOTE: Older model accessory cameras are compatible with CP4S. To connect an older model accessory camera, please utilize adapter SVA-CNVRT-B.

• Camera Channel inputs
  • CP4S has some rules on which cameras can be connected to each input (1~4).

CP4S Power Cable and Wiring

Make sure the vehicle is off, then connect the required wires to the vehicle, as shown below in the wiring diagram.

• Power Connection

• Video Output Cable & I/O Harness (optional)

Mounting Bracket Installation

a. Place the CP4S inside the mounting bracket and secure to vehicle using the 4 provided self-tapping screws.

Locking Enclosure (Optional)

a. Front View (open)

b. Rear View (Closed)

Connecting LCD monitor with Video Output cable (optional)

The following displays can only be seen when a monitor is connected.

1. Connect BNC/RCA cable (included with SmartWitness LCD monitor ) to CP4S Video output (BNC female) and LCD V1 input (RCA female)
2. LCD monitor should be installed in the cab. (download LCD monitor guide from install.smartwitness.com, a printed copy is also included in the LCD package)
3. Connect LCD power cable to a true ignition (IGN+) source and Ground to BAT(-).

The default display is Quad view (2×2) with all cameras shown, to change the video display channel, press the [M2] button to select which camera to view. Each press will change the camera on display with the last option being all camera views.

Final steps

After installation of the CP4S and accessories into the vehicle you can turn on the ignition and CP4S recorder will power on. There will be a sequence of red, blue & green LED lights on the Remote/Panic Button during the boot-up process.

• * Once boot-up is complete, the red light will turn off and there will be only a solid blue & green (only for connected device) light on. This indicates proper operation and recording. If the red light is blinking, then there is an error, then contact your supplier or visit support.smartwitness.com to create a support ticket. _**Please see section 10 for more details on LED status indicators**_.

  • Login to install.smartwitness.com and complete the installation wizard to validate the installation and generate the installation report.
    NOTE: To access install.smartwitness.com, you must first go through mandatory training with SmartWitness. One you complete the training (about a 30-minute webinar), you will be provided login credentials. To schedule training, please complete the online form here: https://www.smartwitness.com /become-installer

• G-Sensor Calibration
  G-sensor calibration is needed after installing the CP4S.
  a) Turn on the unit and wait until it starts recording.
  b) Press and hold M1 button (located at the remote controller) for more than 2 seconds.
  c) You will hear a beep when you press M1 , and then you will hear another beep after 2 seconds. Upon the second beep, you can release M1 button.
  d) Then the calibration will be done within 2 seconds.

Troubleshooting

• The CP4S has a solid red light on as well as solid green and blue.
  • Solid red LED indicates that one of the connected cameras is not receiving view signal. Please check the camera’s connection.
• The CP4S red LED is blinking
  • There is an SD card error/corruption. Please replace the SD card or contact SmartWitness.
  • The new SD card must be initialized with the CP4S Configuration Tool for the device to function properly, and the right settings must be applied.
  • IF SD card is blank (not initialized), the CP4S will automatically initialize the SD card, apply the latest NAND settings, during the rebooting process.
  • There is a power issue. Please verify proper voltage and amperage is being supplied to the Red (BAT+) & White (IGN+) cables on the power harness and that the black cable is properly connected to BAT(-)
• The CP4S green LED is blinking or off.
  • The SIM card is not registered with the cellular network. Please verify the SIM is inserted correctly.
  • If it looks to be inserted correctly, please remove and re-insert the SIM card and try again
  • Power cycle the camera.

Remote Controller Indicators & LEDs Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>