SMARTWITNESS KP1S 3G Enabled Telematics Camera Installation Guide
- June 6, 2024
- SMARTWITNESS
Table of Contents
SmartWitness KP1S + SVC400
Installation Guide
v.1.2
WARNING: SmartWitness installations should be performed by a qualified individual or installation professional only. Working with a vehicle’s power system can be dangerous to both you and your vehicle. This installation is intended only to be a guide since vehicle designs and power/input sources can vary significantly from vehicle to vehicle.
If you need to schedule a professional installation service in the USA for your SmartWitness device(s), please visit http://smartwitness.com/scheduleinstall and submit the online form.
KP1S Contents & Diagram:
*Depending on the order, the 3G Modem and/or SD card may or may not be
included.
**SD Cards, Secondary camera, Power Adaptor, and 3G modems may be in a
separate package from the KP1S (common in large, bulk orders).
SVC400-S Contents & Diagram
KP1S connected with SVC400
Connecting Camera 4: (RCA input) to SVC400
- A rear backup camera (any SmartWitness camera ending in “-C”, ( i.e. SVA036-C )
- Extension cable for the rear backup camera.
- RCA adaptor cable.
- 12V power and ground for rear backup camera connect to IGN (+) and GND (Bat-).
- RCA input on SVC400 recorder.
- SVC400 recorder.
- Video output cable.
- Video output to KP1S ch2 input.
Connecting Cameras 1, 2, & 3 (5V, 2.5mm stereo) to SVC400
- All SmartWitness 5V cameras can plug n play into camera channels 1, 2, & 3 on SVC400
- Compatible camera models end in “-S”, such as the SVA033-S
- All”-S” cameras have a 1ft. lead from the camera lens and include a 16ft. extension cable (33ft cable also available)
- Simply plug the 2.5.mm stereo cable into the desired camera input.
• Camera ch1 must be used with a camera, otherwise, SVC400 will have an error (for example, you can connect cameras to ch1 & ch4 only, but NOT to ch2 & ch4)
NOTE: You can use any analog camera with Ch 1,2, & 3, but you will need to use the provided RCA adaptors
SmartWitness “-S” cameras are powered from the SVC400 recorder cam inputs 1, 2, & 3 only
Connecting 12V camera (cameras ending in “-C” such as SVA025-C) & LCD Monitor stereo)
For customers requiring the SVC400 connected cameras to also display on the LCD monitor, Connect the male USB port from the 3G Modem into the female USB port as seen in the picture below. Secure the male/female USB connection with the provided silicone cold shrink tape. The tape is self-fusing and does not require heat to be applied. It stretches 300% and is fully fused within 24 hours after application.
Advanced Power Adaptor Accessory (Optional)
- For recording after ignition, such as security/surveillance purposes, the SVCSPWK-BW2 device provides a 3-wire connection between the SVC400 recorder and the vehicle (IGN +, BAT+, and BAT-)
- It will automatically cut off the battery power when battery voltage drops below 12v or 24v, or via timed delay shutoff (times are adjustable via dip switch setting on the adaptor)
Technical Specification
| Input Voltage | 9V–38V (± 5%V) |
|---|---|
| Output Voltage | 12V or 24V (Same with input voltage), |
Max capacity: 12V 1.5A or 24V 1A
Operation Temp| -20t “80t
Link to download SVCSPWK-BW2 datasheet (PDFhttps://www.smartwitness.com
Connecting 3G Cellular Modem (optional)
Connect the male USB port from the 3G Modem into the female USB port as seen in the picture below. Secure the male/female USB connection with the provided silicone cold shrink tape. The tape is self-fusing and does not require heat to be applied. It stretches 300% and is fully fused within 24 hours after application. It is best to stretch the tape, start from one end, and overlap at an angle until you reach the other end of the connector.
Secure the male/female USB connection with the provided silicone cold shrink tape. The tape is self-fusing and does not require heat to be applied. It stretches 300% and is fully fused within 24 hours after application. It is best to stretch the tape, start from one end, and overlap at an angle until you reach the other end of the connector.
Remove the 3M adhesive backing and secure the modem to the windshield. The excess USB cable and KP1 S cable should be tucked neatly in the roof lining or along the edge of the windshield. It is recommended to adhere to the modem above the AS1 line, in the “blue zone” of the windshield to reduce the amount of direct sunlight/heat. The modem should not be touching any part of the vehicle frame or metal. DO NOT HIDE THE MODEM IN THE ROOF LINING OR A-PILLAR, this will affect the cellular signal and hinder performance.
Final Steps
After installation of the KP1S and accessories into the vehicle (2nd camera, panic button, & 3G modem), you can turn on vehicle ignition and the KP1S will power on. There will be a sequence of LED lights cycling during the boot process. Once boot-up is complete, there will be solid blue light. This indicates proper operation and recording. If the 3G modem is installed, the Green LED should also be solid on. If Greenlight is blinking, then there is a server error or network error. If a red led comes on after bootup, there is an error and you should contact your supplier. Please see step 8 for more details on LED status indicators.
- After you’ve set the camera angle, lock the cover and remove the key, press the G-Sensor calibration button once (small red button ABOVE the panic button). This will also capture an image from each camera and send it to the server to confirm camera operation and proper camera field of views. The blue LED will flash rapidly for a few seconds when the calibration button is pressed.
- Verify the Blue and Green LED lights on the camera are solid and not blinking. Once the camera makes a successful connection to the server, it may apply an updated configuration file and/or firmware. In this case, the camera will automatically reboot to apply the new settings/firmware. Please make sure the camera reboots and goes back to a solid blue and green LED. *NOTE: only the Blue and Green LEDs should be on. If Red LED is on, see the Troubleshooting/FAQ section for more information.
- Verify the 3G Modem “Link” LED light is on and blinking slowly
- Please visit http://install.smartwitness.com to complete the installation form and click submit.
- Give the provided keyset and any extra parts/accessories to the fleet owner/administrator as well as a copy of the installation report.
Troubleshooting
-
The KP1S has a solid RED light on as well as solid GREEN and Blue Solid RED LED indicates the 2nd camera channel is not receiving a video signal. Please check the camera connection.
-
The KP1S Blue light is solid but the Greenlight is blinking or off Check the “Link” LED on the modem.
• If Link LED is solid, check to make sure the SIM card is inserted properly
• If Link LED is OFF, check the USB connection of the cable and modem
• If Link LED is blinking and the KP1S Green LED is also blinking, it may be a camera configuration issue or server issue. Please contact SmartWitness. -
The 3G modem Link LED is solid on
• The SIM card is not registering with the cellular network. Please verify the SIM is inserted correctly, as seen on page 7.
• If it looks to be inserted correctly, please remove and re-insert the SIM card and try again
• Power cycle the camera -
The KP1S RED LED is blinking
There is an SD card error/corruption. Please replace the SD card or contact SmartWitness -
3G Modem LED specification****
Link Status|
Description
---|---
Off| No power to the unit.
On| Continuously lit| Powered on.
Slow blink (-0.2Hz)| Registered on the network.
For Technical Support, please visit support.smartwitness.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>