TOPEAK TW030 PrepStand eUP Workstand for Electric Bike User Guide

June 6, 2024
TOPEAK

TOPEAK logo PREPSTAND eUP
User’s Guide
Bike weight limitation
TOPEAK TW030 PrepStand eUP Workstand for Electric Bike

WARNING
READ ASSEMBLY INSTRUCTIONS THOROUGHLY.
Care should be taken during assembly as the built-in pressurized nitrogen cartridge may be accidentally deployed.
ENSURE THERE IS ADEQUATE SPACE ABOVE THE CLAMP HEAD UNIT TO AVOID INJURY OR DAMAGE.

**PARTS DESCRIPTION

**

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - PARTS
DESCRIPTION

1. 360° Rotation knob
2. Clamp holder
3. Clamp
4. Clamp jaw lever
5. Clamp jaw
6. Extension tube
7. QR clamp lever| 8. Wheel
9. Wheel chock
10. Support legs
11. Cable end holder
12. Cable retainer
13. Pedal
---|---

SUPPORT LEG ASSEMBLY

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - SUPPORT LEG
ASSEMBLY

NOTE
Always fully extend support leg assembly for a steady foundation.
WARNING
THE WHEEL CHOCK MUST BE INSTALLED WHILE PREPSTAND eUP IS IN USE.
TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
WARNING

**CLAMP ASSEMBLY

**

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - CLAMP
ASSEMBLY

Extend clamp holder lever for the following assembly procedure.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - Extend clamp
holder

NOTE

DO NOT position a quick-release lever where it can be accidentally released.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
NOTE

CABLE ASSEMBLY

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
1

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - CABLE
ASSEMBLY

WARNING
If you can’t place the cable end into the notch smoothly. DO NOT STRETCH THE CABLE TO PLACE IT. Please check whether the cable is out of position first.
TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - LIFT or LOWER
3

WARNING
CARE SHOULD BE TAKEN DURING ASSEMBLY as the built-in pressurized nitrogen cartridge may be accidentally deployed. Ensure there is adequate space above the clamp head unit to avoid injury or damage.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - WARNING
2

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
ASSEMBLY

NOTE
The inner cable will stretch over time. Adjust or replace cable as needed.

FUNCTION TEST

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - FUNCTION
TEST

NOTE
If the clamp still does not raise or lower after checking assembly, it may indicate that the built-in pressurized nitrogen cartridge is damaged. Please refer to page 14 of this User’s Guide on how to examine the cartridge for proper operation.

ATTACH THE BIKE

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - ATTACH THE
BIKE

Once the clamp is set to the desired width, quick adjustments can be made by opening the lever.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -Once
clamp

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - Non-marring
rubber

WARNING

If there is a carbon seat post on the bike to be clamped, replace it with an aluminum seaport before using the Prepstand eUP for safety purposes.

LIFT or LOWER

The built-in pressurized nitrogen cartridge will provide lift assist while you press the pedal. You can stop at any height by releasing the pedal. To lower, press pedal and push down on clamp. Once the clamp is at the lowest position, release the pedal to
lock the clamp in position.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - LIFT or
LOWER

NOTE
Depending on your bike’s weight, you may need to provide additional assistance to lift or lower the bike.

WARNING

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - LIFT or LOWER
1

When operating the stand. It will tilt 3 to 5 degrees and the clamp should be in horizontal.

ROTATION

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
ROTATION

WARNING
ENSURE RATCHET TEETH ARE FULLY ENGAGED and always check stability when operating stand.

DISASSEMBLY

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
DISASSEMBLY

WARNING
The pressurized nitrogen cartridge may cause injury or damage.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - warning
5

WARNING
Ensure there is adequate space above the clamp head unit to avoid injury or damage.

DISASSEMBLY

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - DISASSEMBLY
1

NOTE
Tilt stand forward and remove the wheel chock.
TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -DISASSEMBLY
2WARNING
Ensure wheel chock is positioned correctly when storing to prevent damage to stand legs

EXAMINING PRESSURIZED NITROGEN CARTRIDGE

EXAMINING THE PRESSURIZED NITROGEN CARTRIDGE
The built-in pressurized nitrogen cartridge may be damaged if the clamp head does not lift or lower smoothly during normal operation. Inspect by pressing the cable end holder down to check the function of the pressurized nitrogen cartridge. While the cable end holder is depressed, the clamp holder should raise and can be lowered by pressing down on the clamp holder. If it doesn’t work properly with this method, then the built-in nitrogen cartridge is confirmed to be damaged. Contact your local Topeak dealer for cartridge replacement.

WARNING!!!

Care must be taken when examining the pressurized nitrogen cartridge. Accidental deployment of the pressurized nitrogen cartridge may cause injury or damage.

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike -
test

PARTS DESCRIPTION

Optional accessories

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - Optional
accessories

Repair parts

TOPEAK TW030 PrepStand eUP Workstand for Electric Bike - Repair
parts

NOTE
For cartridge replacement, it is recommended to return the repair stand to the dealer to ensure function and safety.

WARNING NOTES

  1. Always fully extend support leg assembly for a steady foundation.
  2. In case of accidental operation, ensure there is adequate space above the stand to prevent injury or damage during assembly and disassembly of the stand.
  3. Ensure 360° knob is tightened adequately to engage ratchet teeth during assembly and operation.
  4. QR clamp lever should be tightened correctly when assembling and operating the stand.
  5. To prevent possible damage to the bike, DO NOT over-tighten the clamp.
  6. The stand may tilt or fall over if the bike being clamped is over 35kg.
  7. Make sure the clamp assembly is in the lowest position and hold the bike before loosening the clamp.
  8. DO NOT use the standing wheel to reposition the stand if a bike is clamped.
  9. Keep the stand pedal positioned safely when storing or using the stand to prevent accidental operation of the pressurized nitrogen cartridge.
  10. The wheel chock DOES NOT prevent the stand from tipping. Always check the stability of the stand before and during use.

WARRANTY

2-year Warranty: All mechanical components against manufacturer defects only.
Warranty Claim Requirements
To obtain warranty service, you must have your original sales receipt. Items returned without a sales receipt will assume that the warranty begins on the date of manufacture. All warranties will be void if the product is damaged due to user crash, abuse, system alteration, modification, or used in any way not intended as described in this manual.

  • The specifications and design are subject to change without notice.
    Please contact your Topeak dealer with any questions.
    For USA customer service call: 1-800-250-3068
    www.topeak.com

TW030_ML_202104
TOPEAK logo 1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals