Sarabec 1222 Chime Flash Doorbell User Manual
- June 6, 2024
- Sarabec
Table of Contents
Sarabec 1222 Chime Flash Doorbell
Product Overview
Receiver Unit
- Doorbell Icon (Green)
- Battery Low Indicator
- Speaker Port
- General Bell Icon (Orange)
- Flash Lens
- Volume/Setup (Multifunctional)
- Alert Type Selector
- Power Supply Socket
- Battery Compartment
- Battery Compartment Door
- Accept Button
Bellpush
- Push Button
- Push Indicator
- Mounting Bracket
- Battery Cover
- Battery Compartment
Battery Installation
Insert 3 x “C” size alkaline ba eries into the battery compartment on the receiver unit. Remove the battery cover on the push transmitter using a coin and insert the CR2032 battery (Positive side upwards).
Fixing and Wall Mounting
Bellpush
We recommend attaching the bellpush mounting plate to your door or frame using
the sticky pad already attached. The provided screws and plugs can be used for
fixing the bellpush to masonry OR for wall mounting the Receiver unit.
The Bellpush should be fitted to the mounting plate at a 90 degree angle and
then rotated either clockwise or anti‐clockwise until a click is heard.
Receiver
The Receiver can be wall mounted, we would suggest using the screws provided for doing this and mount the bellpush using the sticky pad already attached to the mounting plate.
Initial Setup
Note: chime flash is pre‐programmed and ready to use once the batteries have been inserted. Follow the instructions below if you want to add a transmitter, set a melody or adjust volume.
The multifunction button/wheel has 2 functions, firstly it can be pressed on its front face to enter the setup process, secondly it can be rotated to select melody when in the setup, or to adjust the volume at any other time.
-
Press & hold the setup button for 2‐3 seconds, the green doorbell symbol will illuminate and flash at a steady rate.
-
Press the bellpush transmitter button, the green symbol on the receiver will flash rapidly for 1 second and a single beep will be heard, this indicates that the bellpush and receiver are now paired.
Melody Selection
There are 4 doorbell melodies and 2 telephone melodies to choose from.
Press and hold the setup button for 2‐3 seconds to enter setup mode, the green
symbol will steadily flash. Release the setup button.
If this is the symbol you would like to change the melody of then simply
rotate the setup button until you hear the sound you wish to keep. If you wish
to change the sound on the second symbol press the setup button once, the bell
symbol will flash and follow the instructions above.
Once the desired melody is selected press the setup button to exit the setup
mode.
Volume Control
There are 8 volume levels. Every level has a single beep which corresponds to
the volume level, when you hear a double beep you have reached maximum volume.
The volume level can be set at any time except when in setup mode. The chosen
volume level is the same for both transmitters if using a second bellpush or
telephone transmitter.
Alert Type
chime flash can be set to output Sound Only, Flash Only or Sound and Flash together using the slide switch on the side of the receiver unit.
Accept Button
This button can be used to acknowledge the chime flash alerts, press this button any time when the system is triggered, it will stop it immediately.
Optional Accessories
A Telephone alert transmitter is available which can plug into a BT phone socket, every time the phone rings the chime flash will alert you.
Programming of this accessory is the same as the Doorbell Push (outlined on the previous page).
The chime flash can also be powered by a 12v Mains power supply, when using the system in this way the batteries in the receiver act as a battery back up in case of power failure.
The plug fits into a socket in the back of the receiver and you feed the wire along the retaining channel.
Only the 12v 1A Sarabec power supply should be used with this equipment.
Troubleshooting
Problem
|
Solution
---|---
The RED Indicator on the receiver is blinking every 15 seconds and volume
level has dropped| Replace batteries as they are LOW (replace with “C” size
Alkaline batteries)
The Green or Orange Symbols on the receiver are blinking every 15 seconds|
Replace the corresponding transmitter coin cell battery (CR2032)
I need to clear a transmitter from the systems memory| Enter the setup mode,
then press and hold the setup button for 3 seconds, a beep will be heard,
press the setup button once and clear the second symbol if required by holding
the setup button again for 3 seconds, if not press the setup button again to
leave the setup mode
My system is being triggered at random (Possibly by a neighbour’s doorbell
system)| Open the battery cover of the transmitter, remove the battery, press
and hold the pushbution for 5 seconds whilst inserting the battery back into
the push, the LED will blink 5 times to show that a new code has been
generated.
Clear the transmitter from the memory of the receiver and follow the setup
instructions to re‐pair the transmitter to the receiver again.
I cannot remove my transmitter from its mounting plate| There is a small tab
located on the bottom of the mounting plate which must be pushed away from the
transmitter, this will allow you to rotate the transmitter on the plate to
remove it
If you have a Pacemaker or ICD fitted you may wish to read the FAQ on our website before using this product.
Sarabec Ltd 15 High Force Road Middlesbrough United Kingdom TS2 1RH
Telephone: 01642 247789
email: mail@sarabec.co.uk
website: www.sarabec.com This system carries a 2
year guarantee, please contact your point of sale in the event of
any issues.| Sarabec Ltd declares that chime flash complies with all
relevant UK Statutory Instruments.
Sarabec Ltd declares that chime flash complies with all relevant EU directives.
Sarabec’s EU authorised representative:
HUMANTECHNIK GmbH, Im Wörth 25, D‐79576 Weil am Rhein , Germany.
The full declaration of conformity for the Chimeflash is available from Sarabec
---|---
Specifications
Frequency:| 868.4MHz
Maximum Volume:| Up to 100dB @ 1m
Range:| Up to 300m (Open Space)
Power Requirements| 3 x C size Alkaline batteries or Mains Power 12v 1A PSU
for Receiver
1 x CR2032 for Transmitters
The Wheely bin logo is the industry wide symbol for this type of product. The symbol, when appearing on electronic product, indicates that the item should NOT be treated as ordinary household waste when due for disposal.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>