GOAL ZERO 31901 Yeti 1250 600 Watt Power Supply User Guide
- June 6, 2024
- GOAL ZERO
Table of Contents
600 WATT
POWER SUPPLY
USER GUIDE
IMPORTANT SAFETY INSTRUCTIONS
Use only with Yeti X Lithium Portable Power Stations 1000X, 1500X, 3000X, 6000X
- Working temperature -20 C to 60 C
- Approved by CE, FCC, UL, RoHS certifications
- Short Circuit, Over Voltage, and Over Current Protection Built-in
- DO NOT disassemble or attempt to repair the module
- Please unplug when not in use
- Avoid exposure to rain or moisture to reduce the risk of product damage or electric shock
- Keep this product out of the reach of children
- Use original AC cable
- Use within space large enough to facilitate heat dissipation to extend the life of the power supply
Get To Know Your Gear
How it Works
Charge your Yeti 1000X/1500X/3000X even faster with our Yeti X 600W Power Supply. CAUTION: This 600W power supply is designed exclusively for our Yeti X line to halve charge time, and can not be used for Yeti Lithium or Yeti Lead Acid power stations.
- Fastest charger for Yeti 1000X, 1500X, 3000X. Replacement power supply for Yeti 6000X
- Connect AC Wall Plug into the Power Brick.
- Plug AC connection into a standard wall outlet.
- Connect Red and Black High Power Port (HPP) connection into the High Power Port (HPP) input on your Yeti X Power Station.
- You will see the input indicator light activate when charging.
Technical Specifications
General:|
---|---
Dimensions| 10 x 4.4 x 1.6 in (25.4 x 11.2 x 4 cm)
Gauge| 14AWG
Used with| Goal Zero Yeti 1000X/1500X/3000X/6000X
|
Ports:|
Input| AC Wall Plug 100
Output| HPP 40.0V
Frequently Asked Questions
Why am I seeing less than 600W input into my Yeti?
In order to safely and efficiently charge your battery, the actual input to
your Yeti X may vary from 500W to 600W. The input will usually be lower during
the top end and bottom end of the charging cycle.
Why is my power supply hot?
The heat is normal and can reach temperatures up to 140 Degrees Fahrenheit
(60Degrees Celsius). This is caused by the change in voltage from AC to DC
voltage.
Why is my power station not charging?
Please double check all connections are firmly plugged in. The Yeti Power
Stations have built-in overcharge protection. It is possible your unit is
fully charged or close to a full charge. We would recommend confirming the
functionality at a lower battery level < 80%.
GOAL ZERO HEADQUARTERS
675 West 14600 South
Bluffdale, UT 84065
1-888-794-6250
Designed in the U.S.A.
Made in China
Goal Zero Yeti is a trademark of Goal Zero. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following easures:—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) his device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 42CL081021V1 ****
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>