Danfoss 296 ECL Comfort Instructions

: June 1, 2024
: Danfoss

Table of Contents

Danfoss 296 ECL Comfort
Specifications
Product Usage Instructions
FAQ
USING INSTRUCTION
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Danfoss 296 ECL Comfort

Specifications

Model: ECL Comfort 296 / 310
Connectivity: Ethernet
Remote Control: Yes
Manufacturer: Danfoss

Product Usage Instructions

Connect the ECL 296 / 310 to the Internet

The ECL Comfort 296 / 310 must be connected to the Internet via an Ethernet cable to the Internet gateway. Ensure that the Ethernet settings on the controller match the network it is connected to.

To change settings:

Access Menu->System->Ethernet*
Confirm IP address setup (static or dynamic)
Use the change setting knob on the device or remote control and confirm by pushing the knob

Create your user account

If you do not have an account, visit https://app.lhm.danfoss.com/. Contact your local Danfoss sales representative for assistance.

Register the ECL Comfort 296 / 310

Register the device to your user account via + Connect -> Connect ECL -> select Device type -> ECL-296/310 -> enter serial and installation code. You can find this information in thePortal info menu.

Remote control and monitor it

Once registered, you can remotely control and monitor the heating installation. Adjust settings, monitor temperatures and operations, and receive email alerts.

FAQ

Q : Where can I find the serial number and access code for registration?
A : The serial number and access code can be found in the Portal info menu.

USING INSTRUCTION

Connect the ECL 296 / 310 to the Internet
The ECL Comfort 296 / 310 must be connected to the Internet via an Ethernet cable to the Internet gateway. Check that the Ethernet settings on the controller match the network to which it is connected. Settings can be found under Menu->System-> Ether-net
Confirm whether the IP address has to be static or dynamically obtained by Internet gateway DHCP.
Activate the Leanheat® Monitor in ECL 296 / 310
The Leanheat® Monitor feature is activated in the ECL Comfort 296 / 310 menu
Portal Config> To select the change setting knob on the device or remote control has to be used, confirmation is done by pushing the knob.
The ECL portal hast to be set to OFF (if the ECL Portal is active the setup menu is hidden).
In the setup menu, Leanheat Monitor has to be selected.
Enable the ECL portal to ON (select the change knob on the device that has to be used).
You will need the serial number and access code to be able to register it to your user account. This information can be found in the <System ->Portal info > menu.
Create your user account
https://app.lhm.danfoss.com/ If you do not have an account, please contact your local Danfoss sales representative.
Register the ECL Comfort 296 / 310
Register the ECL Comfort 296 / 310 to your user account via the + Connect -> Connect ECL -> select Device type -> ECL-296/310> enter serial and installation code. The serial number and access code of the ECL Comfort 296 / 310 is needed. (See step 2).
Remote control and monitor it
You are now ready to remotely control and monitor the heating installation. Settings of the ECL Comfort 296 / 310 can be changed, temperatures and operation can be monitored, and you can be alarmed via e-mail.
ECL Comfort 296 / 310: www.danfoss.com
or https://store.danfoss.com/en/

Any information, including, but not limited to information on the selection of the product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogues, brochures, videos and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved

0 8 7 H 9 3 5 8