GOAL ZERO 98079 Yeti 12V Car Charging Cable User Guide
- June 6, 2024
- GOAL ZERO
Table of Contents
GOAL ZERO 98079 Yeti 12V Car Charging Cable User Guide
IMPORTANT SAFETY INSTRUCTIONS
Use with: Sherpa 100AC and Yeti Power Stations
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
Charge only one lithium-ion rechargeable battery at a time. Other types of battery may burst, causing personal injury or damage.
Do not use charger outdoors or expose to wet or damp conditions.
Water entering charger will increase the risk of electric shock.
Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric chock, fire, or serious personal injury.
Do no abuse cord or charger. Damage to the cord or charger could occur and create an electric shock hazard. If cord or charger is damaged, have the charger replaced by an authorized serviceman.
Make sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.
Keep cord from heat to prevent damage to housing or internal parts. Improper use may result in damage to your vehicle, the cable, and the unit.
Get To Know Your Gear
How it Works
Used to safely and efficiently charge Goal Zero Sherpa 100AC and Yeti Power Stations from 12V source (12V up to 10A, Featuring a protective 15A user replaceable fuse.)
-
Connect 12V Male cigarette end of the cable into your car’s 12V cigarette lighter and the other end to the 8mm input port of the Sherpa 100AC or Yeti Power Station.
-
The LED indicator light glows solid green when charging. Input indicator on Sherpa 100AC / Yeti Power Station will illuminate.
-
The car charger will prevent output when vehicle is turned off to prevent draining your car battery.
-
If indicator turns red, attempt to change the 10A to 5A switch to accommodate
your vehicle. -
For best charging results, test all of the vehicle’s 12V outlets to see if any will function on the 10A setting.
-
Use 5A setting when charging a Sherpa 100AC.
Indicator Light
Green: Functional and charging.
Red: Attempt to switch 10A to 5A setting, try different 12V outlets or
change fuse.
Charge Times
Technical Specifications
General:
-
Cord Dimensions: 120 x 2.5 x 1 in (304.8 x 6.35 x 2.54 cm)
-
Used with: Goal Zero Sherpa 100AC and Yeti Power Stations
Use 5A setting on Sherpa power banks -
Certs:
Ports:
- Input 12V Male Cigarette
- Output 8.0mm (12V, up to 10A)
- Switch 12V 5A; 12V 10A
- Fuse 15A glass tube fuse
Frequently Asked Questions
Will the unit charge when the vehicle is off and drain my battery?
No the car charger has built in low voltage protection to prevent charging
when the vehicle is off and prevent draining your car battery.
What do I do if the indicator turns red?
Change from 10A to 5A setting. Not all vehicles are created equal.
Unfortunately some can not maintain 10A output and you will need to switch to
the 5A setting. Most vehicles have multiple 12V outlets, we would recommend
attempting all to see if they function on the 10A setting.
My cable is not functioning and indicator stays red on all 12V sockets. How
do I change the fuse?
There is a 15A Tube fuse in the tip of the male 12V cigarette. Unscrew the tip
( be careful you do not loose any parts) remove the tube fuse to inspect if it
is blown. Replace the tube fuse. These are very common fuses found at most
auto locations.
GOAL ZERO HEADQUARTERS
675 West 14600 South
Bluffdale, UT 84065
1-888-794-6250
Designed in the U.S.A.
Made in China
Goal Zero Yeti is a trademark of Goal Zero
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>