EPSON ELPLX01S & ELPLX01WS Printer User Guide

EXCEED YOUR VISION
ELPLX01S
ELPLX01WS

© 2021 Seiko Epson Corporation
Included Items List
Check the following list to confirm that you have all of the supplied items. If by any chance there is anything missing or damaged, please contact your dealer.
• Lens unit (With lens covers (2 types))
• User’s Guide (this guide)

Safety Instructions

Read this document and the User’s Guide supplied with the projector carefully to use this unit safely and correctly. To allow you to solve any unknown points quickly, keep this information close to hand.
So that you can use the product safely and correctly, symbols are applied in this Guide and on the product to indicate possible harm to the user or to others and the risk of damage to property. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

Warning This symbol indicates information that, if ignored, could possibly result in death or personal injury due to incorrect handling.
Caution This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Warning

• Disconnect the power cable from the projector before attaching or removing this product.
  Attaching or removing while the power cable is connected could cause an electric shock.

• When attaching the product to the projector, make sure that it is securely installed and that it is locked in place. If this product is not attached correctly it may fall, resulting in personal injury or an accident.

• When removing dirt and dust from the projector, do not use a spray that contains flammable gas. The high heat generated inside the projector may cause a fire.

Caution

• When projecting, remove the lens cover from the front of the lens unit.
• Before attaching the lens unit, check the projector’s model number. If this lens unit is attached to a projector other than the specified projector, the lens unit or the projector could be damaged.
• When the projector is installed on the ceiling, uninstall the projector, and then attach or remove the lens unit in a safe location.
• Be careful not to trap your finger when attaching this product to the projector. This may cause an injury.
• Do not disassemble or remodel.
• Do not use or store the projector in places where it might be subjected to high and low extremes of temperature.
• Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it can adversely affect the quality of the projected images.
• Do not get it wet.
• Do not drop it or subject it to impacts. When putting this product down, make sure you place it on a flat, stable surface.
• When moving the projector, do not hold the lens unit. The lens unit may come off and the projector may fall causing an injury.
• Remove the lens unit when transporting the projector. If the projector is transported with the lens unit attached, the lens unit or the projector could be damaged.
• Turn off the projector and then wait for a while (approximately 30 minutes) before removing the lens unit. If you touch the lens unit during projection or immediately after turning off the projector, it could cause a burn.
• If the lens shift has been done, move the lens position to the home position before replacing the lens unit.
• Do not touch or pull the connector part of the cable as this could cause a malfunction.
• When cleaning this product, do not use a wet cloth or solvents such as alcohol, benzine, or thinner as this could cause an electric shock or a malfunction.

Removing and Attaching the Lens Unit

Depending on the projector being used, procedures and illustrations may differ from the explanations. Make sure you read the User’s Guide supplied with the projector.
Attaching
Caution

• When attaching the lens unit, remove the power plug from the electrical outlet first.
• Do not attach the lens unit when the projector’s lens insertion section is facing up. Dust or dirt could enter the projector.
• Try not to touch the lens section with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality deteriorates.

Procedure

1. Remove the lens covers (2 types) from the lens unit.
   Use the covers when storing or transporting the lens unit on its own. Keep the lens covers in a safe place.

2. Pull the lens replacement cover straight out.
   Keep the lens replacement cover in a safe place.

3. Hold the lock lever and turn it counterclockwise.
   

4. Insert the lens unit straight into the lens insertion section with the white circle on the lens on top.
   

5. While holding the lens unit firmly, hold the lock lever and turn it clockwise to lock the lens unit.
   Check that the lens cannot be detached.
   

Lens Calibration
After replacing the lens unit, calibrate the lens so that the projector can correctly acquire the lens position and adjustment range. After attaching a lens unit, a message is displayed when the projector is turned on. Select [Yes] to calibrate the lens.

Removing
Caution
When replacing the lens unit, remove the power plug from the electrical outlet first. If the lens shift has been done, move the lens position to the home position before replacing the lens unit.

Procedure

While holding the lens unit firmly, hold the lock lever and turn it counterclockwise to unlock the lens unit.
Pull the lens unit straight out as it is released.

Adjusting the Image

For more information on the following, see the User’s Guide supplied with the projector.

• Screen sizes and projection distances

• Focus adjustment

• Distortion adjustment
  When you perform distortion adjustment, the size of the screen changes.

• Lens shift

• Keystone correction

• This product is a fixed focus lens. The zoom function is not supported.
  The User’s Guide is available from the following Web site. epson.sn
  Visit the following Web site to find the projection distance calculator. http://www.epson.com/

Specifications

Product name: ELPLX01S/ELPLX01WS
Focusing Length: 5.8 mm
F-Number: 1.9
Operating temperature : 0 to +45°C (No condensation)
Storage temperature : -10 to +60°C (No condensation)
Mass: Approx. 3500 g
Contact your local dealer or the nearest address provided in the documentation supplied with the projector.

External Dimensions

• Screw holes for the optional external camera ELPEC01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>