BRYDGE 12.3 Pro+ Wireless Keyboard with Precision Touchpad User Manual
- June 6, 2024
- Brydge
Table of Contents
BRYDGE 12.3 Pro+ Wireless Keyboard with Precision Touchpad
INSERT/REMOVE
TO INSERT: Place your Brydge on a flat surface and set the hinges upright to 90 degrees. Insert your Surface Pro into the hinges, one side at a time, with the Wake and Volume Buttons on top.
TO REMOVE: Ensure your Brydge is on a flat surface.
Place your hand towards the back of the keyboard and pull up on your Surface
Pro, one side at a time.
POWER
To manually power on, press and hold Fn + Delete keys. The light will turn green for 2 seconds to indicate power.
To manually power off, press and hold Fn + Delete keys for 2 seconds. The light will blink red momentarily to indicate it’s powered off.
PAIR
-
Turn on your Brydge 12.3 Pro+ (Fn+Del), then press and hold the Bluetooth key for three seconds. The Delete key light will flash blue confirming your Brydge is in pairing mode.
-
On your Surface Pro, select:
- Start
- Settings
- Devices
- Bluetooth & other devices
- Add Bluetooth or other device
- Bluetooth
- Brydge 12.3 Pro+
-
Type in the PIN on your Brydge 12.3 Pro+ and hit Enter.
NOTE: If pairing takes longer than three minutes, the blue light will stop flashing and you will need to press the Bluetooth button again.
CHARGE
TO CHECK BATTERY LIFE: go to Windows > Settings > Devices > Bluetooth & other
devices, and check the battery level on ‘Brydge 12.3 Pro+’.
NOTE: If battery life is below 15%, the backlit key functionality will be
disabled to conserve remaining battery life and the light on the Delete key
will blink red.
TO CHARGE: Insert the charging cable into the keyboard and plug the other end
into a power source. A solid red LED on the delete key indicates the Brydge is
charging.
When the keyboard is fully charged, the red LED will turn off. A full charge
can take up to three hours.
SLEEP/WAKE
To conserve battery, your Brydge will enter sleep mode after 15 minutes of
non-use. Press any key to wake it.
When you close your devices together, your Brydge will put your Surface Pro
into sleep mode. When you open your devices, your Brydge will wake your
Surface Pro.
NOTE: Your Brydge will not put your Surface Pro to sleep or wake it after
15 minutes of non-use.
PRECISION TOUCHPAD
The Brydge 12.3 Pro+ touchpad pairs with your Windows device as a Precision Touchpad, and therefore utilizes all of the Windows touchpad gesture capabilities. To adjust the settings and gestures of your touchpad, select Start > Settings > Devices > Touchpad. The Touchpad can be turned on and off by pressing Fn + Alt.
Left Click | Click on left side of touchpad or 1 finger tap
Right Click | Click on right side of touchpad or 2 finger tap
KEYBOARD SHORTCUTS
-
Touchpad Disable/Enable
Fn + Alt (Hold Fn & tap Alt to disable. Hold Fn & tap Alt again to enable.) -
Language Switch
Win + Spacebar (Use spacebar to toggle through available languages.) -
Help
Fn + F1 -
Copy
Ctrl + C -
Cut
Ctrl + X -
Paste
Ctrl + V -
Underline
Ctrl + U -
Italic
Ctrl + I -
Undo
Ctrl + Z -
Task View
Alt + Tab -
Page Up
Fn + Up Arrow -
Page Down
Fn + Down Arrow -
Home
Fn + Left Arrow -
End
Fn + Right Arrow
WARRANTY
This product comes with a 1-year limited hardware warranty on the terms and conditions set out in this document and at www.brydge.com/warranty. All Brydge warranties are non-transferrable and are only available to the original end- user of the product. Warranties do not apply to products purchased from online vendors unauthorized to sell Brydge-branded product. If a defect arises during the warranty period, cease using the product and contact Brydge. To obtain warranty service, visit www.brydge.com/support or call +1 435-604-0481. Brydge, at its sole discretion and option, will (1) repair the product at no charge using new parts or parts that are equivalent to new in performance and reliability, or (2) replace or exchange the product with a product of equivalent functionality and value. Brydge offers free return shipping on any approved warranty claims. A shipping label will be provided to you if you are within the United States. If you are outside the United States, Brydge will reimburse your return shipping to a maximum of US$15.00 after providing a copy of the shipping receipt.
Australia Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Brydge Technologies LLC | 1912 Sidewinder Dr., Suite 104, Park City, UT 84060 USA
HAVE A QUESTION? Visit www.brydge.com/support
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
© 2020 Brydge. All Rights Reserved.
© 2020 Microsoft. Microsoft, the Microsoft logo, Microsoft Surface, Surface,
and the Microsoft Surface logo are trademarks of the Microsoft group of
companies. All other trademarks are the property of their respective owners.
The Bluetooth word mark, and logos are owned by Bluetooth SIG, Inc. Use of
such marks by Brydge is under license. Brydge is a trademark of Brydge Global
Pte. Ltd. Other trademarks and tradenames are those of their respective
owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>