BRYDGE 11 Max+ Keyboard for 11-Inch iPad Pro User Manual
- June 5, 2024
- Brydge
Table of Contents
BRIDGE 11 Max+ Keyboard for 11-Inch iPad Pro
POWER
TO TURN ON: Press the power key for one second until the LED flashes
green.
TO TURN OFF: Press and hold the power key for three seconds until the LED
flashes red.
NOTE: The Brydge 11 MAX+ includes Instant-On'”. which means that
reconnecting no longer takes seconds. Once paired. your keyboard will
instantly connect to your iPad for up to 4 hours before entering sleep mode
without impacting power consumption.
TO PAIR: Press and hold the Bluetooth™ key for three seconds until the
LED flashes blue. On your iPad, under Settings> Bluetooth™ select Brydge 11
MAX+. When successfully paired. the blue LED will turn off and your keyboard
and trackpad will be active.
UPDATE FIRMWARE
Download Brydge Connect from the App Store for the latest firmware updates.
SETTING
Assistive Touch settings must be off for gestures to work properly. To do
this. go to iPad Settings> Accessibility> Touch> AssistiveTouch > OFF
TRACKPAD GESTURES
INSERT /REMOVE
TO INSERT: Place your Brydge on a flat surface and open the case. Place
your iPad in the bottom of the case and lean it towards the back. The magnets
will snap it into place.
TO REMOVE: Place your Brydge on a flat surface. Use the tabs on either
side of the case to release the iPad.
CHARGE
TO CHECK BATTERY LIFE: In Today View. go to the BATTERIES section to
check battery life. If not available. swipe left on your Home Screen to show
Today View, scroll to the bottom and click edit. Scroll down to Batteries. and
click the green ·+· icon to add.
NOTE: If battery life is below 15%, backlit key functionality will be
disabled to conserve battery.
TO CHARGE: Insert the charging cable into the keyboard and plug the other
end into a power source. A solid red LED indicates the Brydge is charging.
When the keyboard is fully charged. the red LED will turn off. A full charge
can take up to three hours.
KEYBOARD SHORTCUTS
WARNING
Thank you for purchasing a Brydge product. This product comes with a 1-year
limited hardware warranty on the terms and conditions set out in this document
and at www.brydge.com/warranty. All Brydge warranties are non-transferrable
and are only available to the original end-user of the product. Warranties do
not apply to products purchased from online vendors unauthorized to sell
Brydge-branded product. If a defect arises during the warranty period, cease
using the product and contact Brydge. To obtain warranty service, visit
www.brydge.com/support or call +l
435-604-0481. Brydge, at its sole
discretion and option, will (1) repair the product at no charge using new
parts or parts that are equivalent to new in performance and reliability, or
(2) replace or exchange the product with a product of equivalent functionality
and value. Brydge offers free return shipping on any approved warranty claims.
A shipping label will be provided to you if you are within the United States.
If you are outside the United States. Brydge will reimburse your return
shipping to a maximum of US$15.00 after providing a copy of the shipping
receipt.
Australia Only: Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Contact Information
Brydge Technologies LLC I 1912 Sidewinder Dr. Suite 104. Park City, UT 84060
USA
Customer Support I +l 435-604-0481 I
support@brydge.com
HAVE A QUESTION? Visit www.brydge.com/support
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions: (1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device. This equipment complies with IC
RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference. (2) This device must accept any
interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by the party
responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates. uses. and can radiate
radio frequency energy and. if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
This wireless keyboard (Brydge 11 MAX+. FCC ID: 2ADRG-BRY403D, IC: 24378-BRY403D) is compatible with the iPad Pro 11-inch (1st generation) ( FCC ID: BCGA1980/BGCA2013/BGCA1934, IC: 579C-Al980/579CA2013/579C- Al934). iPad Pro 11-inch (2nd generation) (FCC ID: BCGA2068/BGCA2230, IC: 579C-A2068/579C-A2230). iPad Pro 11-inch (3rd generation) ( FCC ID BCGA2377/BGCA2459/BGCA2301/ BGCA2460, IC: 579C-A2377/579C-A2459/579C-A2301/579C-A2460) and iPad Air (4th generation) ( FCC ID BCGA2316/BGCA2324/BGCA2325/BGCA2072, IC: 579C-A2316/579C-A2324/579C-A2325/ 579C-A2072).
RF Exposure Information:
FCC RF Exposure requirements: The highest SAR value reported under this
standard during product certification for use next to the head with the
minimum separation distance of 0mm. This transmitter must not be collocated or
operating in conjunction with any other antenna or transmitter.
This product is compliance to FCC RF Exposure requirements and refers to FCC
website https://apps.fcc. gov/oetcf/eas/reports/GenericSearch.cfm search for
FCC ID: 2ADRG-BRY 403D
This EUT is compliance with SAR for general population/uncontrolled exposure
limits in IC RSS-102 and had been tested in accordance with the measurement
methods and procedures specified in IEEE 1528 and IEC 62209. This equipment is
safe to use next to your body. This device and its antenna(s)must not be
colocated or operating in conjunction with any other antenna or transmitter.
© 2021 Brydge. All Rights Reserved.
iPad and Apple are registered trademarks of Apple Inc .. registered in the
U.S. and other countries. The Bluetooth word mark, and logos are owned by
Bluetooth SIG, Inc. Use of such marks by Brydge is under license. Brydge is a
trademark of Brydge Global Pte. Ltd. Other trademarks and tradenames are those
of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>