BRYDGE Series II 10.5 Inch Wireless Keyboard User Manual
- June 4, 2024
- Brydge
Table of Contents
BRYDGE Series II 10.5 Inch Wireless Keyboard User Manual
INSERT/REMOVE
IMPORTANT
Remove non-Brydge screen protectors before attaching your Brydge keyboard.
This will ensure a perfect fit and eliminate unnecessary pressure to your
screen when inserted into the hinges.
TO INSERT: Place your Brydge on a flat surface and set the hinges upright to 90 degrees. Insert your iPad into the hinges with the home button on the right, one side at a time.
If your iPad is loose, remove it and gently squeeze the hinges. Repeat this
process until your iPad is held firmly.
TO REMOVE: Ensure your Brydge is on a flat surface. Place your hand towards
the back of the keyboard and pull up, one side at a time.
POWER
TO TURN ON: Press the power key for one second until the LED flashes green. TO TURN OFF: Press and hold the power key for three seconds until the LED flashes red. NOTE: To conserve battery, your Brydge will enter sleep mode after 20 minutes of non-use. Press any key to turn back on. Your Brydge will enter sleep mode when both devices are closed like a laptop.
PAIR
TO PAIR: Press and hold the Bluetooth key for three seconds until the LED flashes blue. On your iPad, under Settings > Bluetooth select Brydge 10.5. When successfully paired, the blue LED will turn off.
CHARGE
TO CHECK BATTERY LIFE: Press and hold the battery key until the LED flashes three times. The color of the flash indicates the battery level. NOTE: If battery life is below 15%, backlit key functionality will be disabled to conserve battery. TO CHARGE: Insert the charging cable into the keyboard and plug the other end into a power source. A solid red LED indicates the Brydge is charging. When the keyboard is fully charged, the red LED will turn off. A full charge can take up to three hours.
KEYBOARD SHORTCUTS
WARRANTY
Thank you for purchasing a Brydge product. This product comes with a 1-year limited hardware warranty on the terms and conditions set out in this document and at www.brydge.com/warranty. All Brydge warranties are non-transferrable and are only available to the original end-user of the product. Warranties do not apply to products purchased from online vendors unauthorized to sell Brydgebranded product. If a defect arises during the warranty period, cease using the product and contact Brydge. To obtain warranty service, visit www.brydge.com/support or call +1 435-604-0481. Brydge, at its sole discretion and option, will (1) repair the product at no charge using new parts or parts that are equivalent to new in performance and reliability, or (2) replace or exchange the product with a product of equivalent functionality and value. Brydge offers free return shipping on any approved warranty claims. A shipping label will be provided to you if you are within the United States. If you are outside the United States, Brydge will reimburse your return shipping to a maximum of US$15.00 after providing a copy of the shipping receipt.
Australia Only: Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Brydge Technologies LLC | 1912 Sidewinder Dr., Suite 104, Park City, UT 84060
USA
HAVE A QUESTION? Visit www.brydge.com/support
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
This Bluetooth keyboard (Brydge 10.5. FCC ID: 2ADRG-BRY801, IC: 24378-BRY801) is compatible with the iPad Air (3rd generation) (FCC ID: BCGA2152/BGCA2123/BGCA2153, IC: 579C-A2152/579C-A2123/579C-A2153) and iPad Pro (10.5-inch) (FCC ID: BCGA1701/BGCA1709, IC: 579C-A1701/579C-A1709).
© 2019 Brydge. All Rights Reserved. iPad and Apple are registered trademarks of Apple Inc., registered in the U.S. and other countries.
The Bluetooth word mark, and logos are owned by Bluetooth SIG, Inc. Use of such marks by Brydge is under license. Brydge is a trademark of Brydge Global Pte. Ltd. Other trademarks and tradenames are those of their respective owners..
MODEL: BRY8001 SKU: BRY8001
Complies with IMDA Standards
DA105282
MODEL: BRY8001 SKU: BRY8002
Complies with IMDA Standards
DA105282
MODEL: BRY8001 SKU: BRY8003
Complies with IMDA Standards
DA105282
MODEL: BRY8001 SKU: BRY8004
Complies with IMDA Standards
DA105282
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>