Intermec Full Roll Rewinder PM43 Installation Guide
- June 6, 2024
- Intermec
Table of Contents
PM43
Full Roll Rewinder
Installation Instructions
Intermec Technologies Corporation
Worldwide Headquarters
6001 36th Ave.W.
Everett, WA 98203
U.S.A.
www.intermec.com
The information contained herein is provided solely for the purpose of
allowing customers to operate and service Intermec-manufactured equipment and
is not to be released, reproduced, or used for any other purpose without the
written permission of Intermec Technologies Corporation.
Information and specifications contained in this document are subject to
change without prior notice and do not represent a commitment on the part of
Intermec Technologies Corporation.
© 2012 by Intermec Technologies Corporation. All rights reserved.
The word Intermec, the Intermec logo, Norand, ArciTech, Beverage Routebook,
CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet, Fingerprint, INCA
(under license), i-logistics, Intellitag, Intellitag Gen2, JANUS, LabelShop,
MobileLAN, Picolink, Ready-to-Work, RoutePower, Sabre, ScanPlus, ShopScan,
Smart Mobile Computing, SmartSystems, TE 2000, Trakker Antares, and Vista
Powered are either trademarks or registered trademarks of Intermec
Technologies Corporation.
There are U.S. and foreign patents as well as U.S. and foreign patents
pending.
Install the Full Roll Rewinder
Use these instructions to install the full roll rewinder on the Intermec PM43
printer. 
You will need these tools to install the full roll rewinder:
-
T20 Torx screwdriver
- Small wrench.
Warning The full roll rewinder must only be installed by an authorized
service technician.
** Follow standard ESD guidelines to avoid damaging the equipment you are
servicing.
Caution** Before you begin, turn off the printer and disconnect the power
cord and communication cables.
Warning The electronic compartment contains wires and components with dangerous voltage (up to 380 V). Make sure that the printer is switched off and the power cord is disconnected before the cover is removed.
To remove the media cover
- Open the media cover.
- Use the small wrench to loosen the nut that secures the media cover latches in place.
- Slide the latches counterclockwise into the open position.
- Lower the media cover and lift it off the hinges.
- Put the media cover aside on a soft cloth to avoid scratches.
To remove the electronics cover
- Use a T20 Torx screwdriver to remove the two screws that secure the electronics cover to the inside of the printer base. ****
- Use a T20 Torx screwdriver to remove the two screws located on the outside of the electronics cover.
- Remove the electronics cover, and put the cover aside on a soft cloth to avoid scratches.
To install the full roll rewinder
- Open the media access door and pull up on the ends of the door until it snaps off of the printer base.
- Remove the three screws that connect the tear bar to the printer and remove it.
- Remove the five screws that attach the printer spine to the base.
Remove One Screw from the Media Side of Base
Remove Four Screws from the Electronics Side of Base - Lift the spine away from the printer base.
- Attach the spine to the full roll rewinder with the five screws removed in Step 3.
Attach the Spine with Four Screws on the Electronics Side Attach the Spine with One Screw on the Media Side - Connect the grounding strap to the printer spine with one of the screws. Make sure the M4 serrated washer is located between the extrusion from the base and the grounding strap. ****
- Feed the full roll rewinder cable through the cable clip and then insert it into the RWNDR connector on the main logic board. ****
- Replace the electronics cover.
- Attach the batch plate with the three screws you removed from the tear bar in Step 2.
- Replace the media cover.
- Open the full roll rewinder door and move the media roll guide out to the edge of the base.
- Raise the media roll guide to the upright position and insert the cardboard core onto the media roll rewinder hub.
- Close the full roll rewinder door.
- Close the media cover.
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
© 2012 Intermec Technologies
Corporation. All rights reserved.
PM43 Full Roll Rewinder Installation Instructions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>