4iiii PRECISION PRO Ultegra R8000 Power Meter User Guide
- June 6, 2024
- 4iiii
Table of Contents
PRECISION PRO
POWERMETER
Podiiiium Pro
POWERMETER
Quick Start Guide
GETTING STARTED
Tiiiip: Find the complete user manual online: 4iiii.com/support-and- documentation
1. Install your 4iiii powermeter cranksets and pedals following the
manufacturer’s instructions.
Podiiiium: Wake Podiiiium up from shipping mode by plugging it into a
power source for 5 seconds.
2. Download the 4iiii app for iOS or Android.
3. Wake up your 4iiii powermeter by rotating the crank 3 or 4 times.
Tiiiip: Need more
assistance? Go to 4iiii.com/support for FAQs and
customer support.
PAIR YOUR POWERMETERS
Tiiiip: Find the 4iiii app guide online: 4iiii.com/support-and-
documentation
4. Pair the left and right powermeters using the 4iiii App. Once paired,
the left powermeter collects and transmits data from both sides, sending
cadence, total power, and L/R balance to your connected devices as one signal.
a. Open the 4iiii app.
b. Select Add Device.
c. Select both the left and right powermeters. A check mark indicates the device is selected.
d. Select Pair on iOS or Connect on Android.
Your PRECISION PRO or Podiiiium Pro powermeter is paired, connected and ready
to use!
Tiiiip: You can can identify your device using its ANT+ ID. This number
is etched onto the side of the powermeter pod.
CONNECT & CALIBRATEG
Tiiiip: Zero your powermeter before riding in the environment and temperature you will be riding in!
5. Pair your 4iiii powermeter with your power capable device.
6. Zero your
4iiii powermeter using your paired device. With the bike upright and
stationary, unclip pedals and position crank arms as shown. Select “Zero
offset” or “Calibrate” on your display.
Tiiiip: Be sure to update your firmware if prompted. We’re always making
improvements and adding new features.
REGULATORY COMPLIANCE
FCC ID: ZZNPM100 Model: PM100
FCC ID: ZZNPX1Ø2 Model: PX102
FCC Statement: This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment. The device has been
evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED Certification Number: 9896A-PX102, 9896A-PM100,
Model: PX102 PX102, PM100
Statement This device complies with Innovation, Science and Economic
Development Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device. CAN ICES-3(B)/NMB-3(B)
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
FOR TECHNICAL SUPPORT PLEASE CONTACT YOUR 4iiii AUTHORIZED
DEALER.
4iiii Innovations Inc.
141 2 Ave E Cochrane, Alberta Canada
T4C 2B9 Web:
4iiii.com/support
Email: support@4iiii.com
Phone: 1.800.218.3095
Find the complete User Manual online: 4iiii.com/support-and-
documentation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>