Dualit 72960 Pour Over Kettle Instruction Manual

Dualit 72960 Pour Over Kettle Instruction Manual

IMPORTANT SAFTEY PRECAUTIONS

READ ALL INSTRUCTIONS BEFORE USING THE KETTLE
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

• THIS IS AN ATTENDED APPLIANCE. Do not leave appliance unattended during use, unplug after each use (risk of fire if an unattended appliance is left operating or plugged in).

• This appliance is intended for household use only. If the appliance is used improperly or for professional or semi-professional purposes or if it is not used according to these instructions the Guarantee becomes invalid and Dualit refuses any liability for damage caused.

• Do not use the kettle for any purpose other than heating water. Otherwise, this will result in an injury caused by misuse.

• This appliance must not be used by children younger than 8 years old and persons with very extensive and complex disabilities.
  Children aged 8-14 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge shall not use this appliance, unless they are supervised and have been given instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.
  Keep the appliance and its cord out of reach of children less than 8 years old.

• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  Before connecting to the mains supply:

• Check that the voltage marked on the appliance corresponds with the supply voltage.
  Risk of electric shock and fire.

• NOTE: Any plug cut from the power supply cord should be disposed of immediately. Inserting any cut off plug into a 13A socket outlet is hazardous. Risk of electric shock and fire.

• Never use the plug without the fuse cover fitted. Ensure replacement fuse is the same current value as the original. Replacement fuses are available and should be ASTA approved to BS1362. Risk of electric shock and fire.

• In order to avoid a hazard, if the Power Cord is damaged it must, for safety reasons, be replaced by Dualit or an authorised Dualit repairer. Call Dualit’s
  Customer Helpline on +44 (0)1293 652 500.
  Risk of electric shock and fire.

• To be protected against electrical hazards, fire and injury to persons, do not immerse the mains lead, plug, Power Base or kettle in water or any other liquid. Risk of electric shock.

• Do not operate any appliance with a damaged lead or plug, or after the appliance malfunctions or has been dropped, damaged or cracked in any manner. Risk of electric shock, fire and scalding.

• Do not place the kettle, Power Base or mains lead on or near any hot surface, hot hob, gas burner or in a heated oven. Risk  of fire.

• Ensure that the kettle is correctly positioned on the Power Base before switching on.

• Do not operate the kettle on an inclined plane. Risk of scalding.

• Do not use in bathroom or outdoors. Risk of electric shock.

• Do not store or use in an appliance garage or under cupboards. Risk of fire.

• Do not fill above the ‘max’ mark on the water level indicator. Risk of scalding and electric shock.

• Remove the kettle from its Power Base before filling or pouring.

• Do not operate the kettle unless it contains at least 250ml of water and the floor of the kettle is covered.

• Ensure that the Lid is fully closed before switching the kettle on, otherwise it may not properly switch off and take longer to heat water.

• Do not move the kettle while it is switched on. Risk of scalding.

• Do not remove or open the lid while the water is heating. Risk of scalding.

• Use handles or knobs – do not touch hot surfaces. Risk of burns.

• Water will remain hot for a considerable time after heating and can present a scald hazard. Keep the kettle, Power Base and the mains lead away from the edge of worktops and out of the reach of children. CAUTION:
  This kettle has a hold function which will maintain the temperature for a further 5 minutes after reaching target temperature.
  Keep out of reach of children. Risk of scalding.

• When heating, hot steam will be emitted from the kettle. Scalding will occur if you are within 400mm of the Lid, Spout or Steam Vents either side of the lid.

• Ensure that the kettle Spout is pointing away from any electrical plug or socket. Risk of electric shock and fire.

• Scalding will occur if the Lid is opened during the heating cycle and the body of the kettle will get hot.

• This kettle features boil-dry protection. If the kettle is accidently switched on without water, the boil-dry device will switch off the heating element to prevent damage to the kettle. Wait approximately 10 minutes for the kettle to cool down, lift and refill as normal. The kettle is now ready to use again.
  NOTE: If discoloration of the heating plate has occurred, this can be easily removed by descaling your kettle.

• Take care when pouring – pour slowly and do not over-tilt the kettle.

• Avoid spilling of any liquid on the connector.
  Risk of electric shock.

• Allow the kettle to cool down completely before cleaning and storing.

• To disconnect, remove plug from wall outlet.

• Unplug the Power Base from the wall socket when not in use, or before moving and cleaning.

• Use the kettle only with the Power Base supplied and vice versa.

• The use of accessory attachments not recommended by Dualit may result in fire, electric shock or injury to persons.

• CAUTION: To prevent damage to the appliance, do not use alkaline cleaning agents.
  When cleaning, use a soft cloth and a mild detergent. Risk of electric shock.

• Do not use scouring pad or abrasive cleaner on the appliance body.

• Do not heat the kettle if filled with descaling solution. Risk of scalding.

• Before using the kettle for the first time or if it has been out of use for a long time, fill to the ‘max’ mark and boil. Discard all of the boiled water then rinse the kettle out with fresh cold water. Repeat 3 times. Carefully inspect the inside of the kettle and remove any debris.

• Do not fill via the Spout.

• A short Power Cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. Risk of scalding.

• If the kettle is overfilled, hot water may be ejected. Risk of electric shock and scalding.
  SAVE THESE INSTRUCTIONS

Unpack the box with care, keeping all the packaging materials until you are satisfied everything is present and in working order. Once satisfied remove any tags from the appliance body and recycle the packaging appropriatley.
Do not remove tags from the cord. You may wish to keep the box to store. your appliance.

KNOW YOUR POUR OVER KETTLE

• A. Gooseneck Spout 11.0mm for the optimal pour over flow rate.

• B. Lid Knob

• C. Lid

• D. Steam Vents
  CAUTION: WHEN HEATING, HOT STEAM WILL BE EMITTED FROM THE KETTLE. SCALDING WILL  OCCUR IF YOU ARE WITHIN 400MM OF THE LID, SPOUT OR STEAM VENTS EITHER SIDE OF THE LID.

• E. Handle

• F. Power Cord

• G. Start/Stop Button (centre of dial)

• H. Control Dial

• I. Screen

• J. Hold Button

• K. Power Base

• L. Temperature Unit Button

In the interest of improving products, Dualit Ltd, reserves the right to change the product specification without prior notice.
All illustrations are for representation only, your model may vary from illustrations shown

SETTING UP

• 1.A
  Register your product at Dualit.com this will only take 60 seconds; you will need the product model and serial number.

• 1.B
  Place the kettle as close to the wall socket as possible. When in use ensure the kettle is not placed under kitchen cabinets.
  DO NOT STORE OR USE YOUR KETTLE IN AN APPLIANCE GARAGE OR UNDER CUPBOARDS.

• 1.C
  Use the shortest cord possible.
  Wrap excess cord round the cord tidy underneath the Power Base.

• 1.D
  Do not operate on an inclined plane.

• 1.E
  Do not operate in a tray

FILLING YOUR KETTLE

WARNING: IF THE KETTLE’S HEATING CYCLE HAS JUST FINISHED, IT WILL BE FULL OF STEAM, WHICH WILL ESCAPE AS SOON AS THE LID IS OPENED. THE LID WILL BE HOT.

• 2.A
  Ensure the kettle is unplugged. Remove the kettle from the Power Base. Lift the Lid, using the Lid Knob to  open.

CAUTION: WHEN HEATING, HOT STEAM WILL BE EMITTED FROM THE KETTLE. SCALDING WILL OCCUR IF YOU ARE WITHIN 400MM OF THE LID, SPOUT OR STEAM VENTS EITHER SIDE OF THE LID.

• 2.B
  Fill the kettle through the Lid opening. Use at least one cup of water (250ml). The water level must stay below the max mark. Save energy, only heat what you require. Keep kettle upright and level at all times when filling. DO NOT OVERFILL OR FILL THROUGH THE SPOUT.

• 2.C
  Push the Lid down using the Lid Knob and check it is firmly in place. WARNING: IF THE KETTLE’S HEATING CYCLE HAS JUST FINISHED, THE METAL PARTS OF THE LID WILL BE HOT
  

CONTROL FUNCTIONS

Your Pour Over Kettles’ functions can be adjusted using the Control Buttons.

and anti-clockwise to decrease the target temperature.
Start/ Stop Button| | Start/stop water heating| When Screen is illuminated, press to start or cancel water heating.
Temperature Unit Button| | Fahrenheit/Celsius| Press once to toggle between °F/°C. Screen will display the unit selected.
| Mute key tones and feedback sounds| Press and hold for 3 seconds to mute all key tones and feedback sounds.  symbol will show on the Screen when muted.
Hold Button| | Temperature hold| Press once anytime during heating cycle to hold the set temperature for 5 minutes, even if you remove kettle from Power Base. Note: You can only hold up to 96°C/205°F.

Note: Lifting kettle off Power Base during heating will not cancel the cycle immediatley. The cycle will continue when kettle is placed back on the Power Base within 10 minutes. After 10 minutes the cycle is automatically cancelled. You will need to press the Start/Stop Button once, the Start/Stop Button will illuminate. Then press again and the Screen will illuminate.

KNOW YOUR SCREEN

HEATING WATER

BEFORE FIRST USE: FILL TO THE MAX MARKER, BRING TO THE BOIL BY SELECTING 100°C/212°F, THEN DISCARD WATER. REPEAT THIS PROCESS TWICE.

Note: Power Base controls will not operate if the kettle is not placed on the Power Base.

• 3.A
  Ensure the kettle is filled with water, lid firmly in place and sat on the Power Base. Save energy, only heat what you require. Ensure Spout is not close to or facing the user, or a wall/cabinet.

• 3.B
  Plug in, the Start/Stop Button will illuminate.

• 3.C
  Press the Start/Stop Button, the Screen will illuminate and display current water temperature and the set temperature. Note: If kettle is not correctly fitted to the power base or removed at this point, the Screen will look like this.

• 3.D
  Select your target temperature with the Control Dial.

• 3.E
  Press the Start/Stop Button to begin heating water. will show on Screen to indicate heating. **CAUTION: WHEN HEATING, HOT STEAM WILL BE EMITTED FROM THE KETTLE. SCALDING WILL OCCUR IF YOU AREWITHIN 400MM OF THE LID, SPOUT OR STEAM VENTS EITHER SIDE OF THE LID.

**

• 3.F
  Press the Hold Button if you want to maintain the temperature for 5 minutes once the kettle has reached the target level. The hold timer will appear on the Screen.
  **Note: You must press Hold Button before target temperature is reached.

**

• 3.G
  Once target temperature is reached, the Power Base will beep and stop heating.
  **Note: Will not beep if muted.

**

• 3.H
  If you pressed the Hold Button, the hold timer will begin counting down once the target temperature is reached. The Power Base will beep 3 times at the end of the countdown and stop heating.
  **Note: Will not beep if muted.

**

• 3.I
  Remove kettle from the Power Base. To avoid the risk of splashing, wait 10 seconds after the cycle has finished, before pouring slowly. Do not over-tilt the kettle.

• 3.J
  Always unplug kettle after each use. WARNING: After 10 minutes of no use or input from user, the lights will turn off but the Power Base remains energized. Press the Start/Stop Button once and the Start/Stop Button will illuminate, press again and the Screen will illuminate. ATTENDED APPLIANCE, UNPLUG WHEN NOT IN USE: FIRE RISK.
  

OPTIMAL BREW TEMPERATURES

Follow our guide below for various hot drink brewing temperatures. All coffees will brew best at the same temperature, however teas will vary as some leaves are more delicate than others. If your drink comes with its own brewing instructions, follow its guide.

HOW TO MAKE THE PERFECT POUR OVER COFFEE

Dualit recommends using the Dualit Drip Through Coffee Filter with a No. 4 filter paper. If using the Dualit Handheld Grinder, we recommend using Grind Setting 10.

• 4.A
  Add 7–15g per cup of medium-fine grind coffee depending on taste. The grind texture should resemble table salt/fine sugar. If using shop bought, look for coffee suitable for “All Coffee Machines”, “French Press” or “Filter Coffee”.

• 4.B
  To pre-infuse, set to 93°C/200°F then pour a small amount of water over the coffee.

• 4.C
  Wait a few seconds, then in a circular motion slowly pour the hot water over the coffee, making sure to cover all the grounds. The grounds will bloom, allow this to settle before adding more water. Never fill above the max marker/1cm below the filter paper lip, otherwise coffee grinds will end up in your drink.

• 4.D
  Continue to slowly add more water, roughly 50ml at a time, allowing the water to pass through the coffee before adding more.

• 4.E
  Keep an eye on the fill level of the cups and stop pouring when they are about ¾ full/250ml per cup. The entire pouring process should take between 2-3 minutes.

CLEANING & CARE

• 5.A
  Before cleaning, make sure the appliance is switched off, unplugged and allowed to cool. Remove kettle from the power base. Wipe the outside and inside surfaces with a damp cloth. Ensure that all connectors and sockets are kept dry.

DO NOT IMMERSE THE BODY, POWER BASE, POWER CORD OR PLUG INTO WATER OR OTHER LIQUID. RISK OF ELECTRIC SHOCK AND FIRE. DO NOT USE SHARP, ABRASIVE OR AGGRESSIVE CLEANING AGENTS, BLEACH OR SCOURING PADS TO CLEAN THE APPLIANCE. THE USE OF SUCH CLEANING IMPLEMENTS MAY AFFECT THE LIFE OF THE APPLIANCE.

LIMESCALE WARNING!

LIMESCALE BUILD UP
It is important to regularly descale your kettle to prevent limescale building up over time. This build up can cause damage to your kettle and alter the way your hot drinks taste. Follow these steps to minimise limescale build up in your kettle: Empty the kettle after each use; do not leave water in the kettle overnight. Use filtered water instead of tap water. Avoid using bottled water as this is classed as hard water.

DESCALE REGULARLY
Dualit recommends descaling regularly; at least once a month. If you live in a hard water area you may need to descale more often. See our Water Hardness map to determine how often you should descale your kettle. Dualit commends Kilrock K Multi-Purpose Descaler. This can be purchased from www.dualit.com. Other descalers can be used; follow the instructions on the packaging. When descaling has finished empty the kettle and rinse it out a minimum of 3 times with fresh water. Refill with fresh water, set to 100°C/212°F then discard the boiled water. FAILURE TO DO SO CAN CAUSE INJURY. DO NOT HEAT KETTLE WITH DESCALING SOLUTION IN IT.

BRITISH ISLES & IRELAND WATER HARDNESS MAP

WATER HARDNESS TABLE

WATER HARDNESS| Hardness level| | |
---|---|---|---|---
CaCO3 mg/l| 0-100| 101-200| 201+
ACTION FREQUENCY| Descale| At least once every 4 months or every 200 cycles.| At least every 2 months or every 100 cycles.| At least once per month or every 50 cycles.

TROUBLESHOOTING

KETTLE IS PLUGGED IN BUT THE SCREEN AND LIGHTS ARE NOT WORKING
The appliance needs waking up.| Press the Start/Stop Button to illuminate the Screen.
The Kettle has not been used for 10 minutes.| Press the Start/Stop Button, it will illuminate. Press the button a second time to wake and illuminate the Screen.
The Kettle is not on the Power Base.| Return the Kettle to the Power Base to remove the dashes across the Screen.
Ensure the Kettle is correctly sat on the Power Base.
The Kettle may not be properly connected to the power supply or the fuse may have failed.| Check the plug is in the socket and the switch is turned on. Replace the fuse if necessary.
THE KETTLE DOES NOT HEAT WATER
Boil dry feature may have been activated. If the Kettle is accidentally switched on with no water inside, the boil-dry device will switch off the heating element to prevent damage to the Kettle.| Wait 10 seconds for the Kettle to reset. NOTE: if discolouration of the heating plates has occurred, this can be easily removed by descaling your Kettle.
WATER IS SPURTING OUT OF THE SPOUT
You may have over filled the Kettle.| Only fill to the max mark (800ml).
Wait 10 seconds to allow the heated water to settle before pouring.
The Kettle may have descaling solution remaining inside the body.| Follow the instructions from the cleaning & care section and rinse thoroughly.
MY KETTLE IS NOT SWITCHING OFF OR TAKING LONGER THAN USUAL TO HEAT
Limescale may have built up inside the Kettle.| Descale your Kettle regularly (see cleaning & care).
Kettle may have been removed before reaching previous target temperature.| Press Start/Stop Button to cancel the heating cycle.
MARKS HAVE APPEARED IN THE KETTLE
Small brown spots can build up inside the Kettle. This is not rust, small deposits of limescale that contain iron can build up inside the Kettle.| Descale regularly (see cleaning & care).
WATER DROPLETS COLLECT ON TOP OF THE POWER BASE
This is condensation and perfectly normal.| Dry with non abrasive cloth.
WATER ISN’T FLOWING FROM THE SPOUT
The Spout has been blocked with a build-up of limescale.| Descale regularly (see cleaning & care).
HEATED WATER IS THE WRONG TEMPERATURE
Limescale may have built up inside the Kettle.| Descale your Kettle regularly (see cleaning & care).
The wrong temperature units have been selected.| Press the Temperature Unit Button to toggle between temperature units. Screen will display unit selected.
THE KETTLE IS NOT BEEPING
The Kettle is muted.| Press and hold the Temperature Unit Button for 3 seconds to unmute the Kettle.
HOLD TIMER IS NOT COUNTING DOWN
The Hold Button was pressed after target temperature has been reached.| Ensure to press the Hold Button during the heating cycle, before reaching the target temperature.

DON’T FORGET TO REGISTER YOUR PRODUCT
WWW.DUALIT.COM/REGISTER
**OR BY POST

**

Dualit Limited County Oak Way Crawley West Sussex RH11 7ST
+44(0)1293 652 500
info@dualit.com
www.dualit.com

References

• Dualit | Toasters, Kettles, Coffee, Capsules & Pods, Food Processors, Catering Equipment Manufacturers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>