Fubag 120101 Air Tool Kit User Manual

Fubag 120101 Air Tool Kit

WEB:www.fubag.ru

WARNING! BEFORE USING AIR SPRAY GUN PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY.
ONLY QUALIFIED AND WELL-TRAINED STAFF ACQUAINTED WITH THE MANUAL CAN USEAND OPERATE THIS TOOL
This manual contains description, safety rules and all necessary information for proper operating FUBAG air spray guns. Please save the instruction and refer to it when any questions regarding safe operation, maintenance, storage and transportation of FUBAG air spray guns appear. Not following recommendations stated below may cause damages to the air spray gun and operator s injuries’.

Safety rules

• Danger:
  • To direct the air tool or the flow of compressed air to people, animals or your own body. (To avoid ingress of small particles of dust into your eyes, wear protective goggles).
  • To direct the flow of compressed air to the compressor.
  • To work without protective boots, to touch the operating compressor by wet hands and/or feet.
  • To exceed required working pressure.
  • To fix not original spare parts.
• Caution:
  • While connecting the air tool to the compressor s hose, don t forget to turn the air cock.
  • While working with compressed air, follow all safety rules

Technical specifications

Set

| Gravity air spray gun (kit 120101) or suction air spray gun (kit 120102); nozzle 2 mm kit; washing spray gun; air dusting gun; inflating gun; nylon

spiral tube 5 m.

The manufacturer reserves himself the right to make the manual’s content or tool function change without any preliminary notification of the users.

Accessories connection

Make sure that the compressor is OFF before connecting the accessories

1. All the accessories are fitted with quick connectors as shown above (figures. 2). All the accessories are connected to the compressor via the coiled air line using the quick connector.
2. For safety reasons, certain accessories must operate at a specific air pressure indicated in the sections dedicated to these in the following pages. You can check the pressure level by looking at the gauge or the numbered notches on the knob whose values represent the related pressures.
3. Make sure that pressure adjustment knob A is turned fully in an counterclockwise direction, thus shutting off the air supply before starting the compressor.
4. Connect the coiled air line B to compressed air outlet (fig. 1) using couplingCD. Push coupling D firmly inside outlet C.Aclicking noise will indicate that the coupling is engaged.
5. Once you have fastened this end of the coiled air line B, you can connect any accessory to the other end , pushing firmly, for example, couplingEFinside (figures 2). In thisEcase also, a clicking noise will indicate that the coupling is engaged
6. When the coiled air line is connected securely both to the compressor and the accessory, you can start to use the compressor.
7. Switch on the compressor. Once the pre-set pressure has been reached, the compressor will switch off automatically.
8. When you have finished using the accessory, close the compressed air outlet by fully rotating pressure regulation knob A in a counterclockwise direction. Test that the air supply is closed by operating the accessory until all the air has been used. At this point, disconnect the coiled air line from the compressor by pulling back outer sleeve G(fig. ). Disconnect coupling Efrom the accessory according to the procedure explained for coupling (fig. 1).
   It is normal for the compressor to stop and start automatically at intervals as use of compressed air varies.

Paint spray gun

• Always wear a protective mask, goggles and protective gloves when spray painting. Spray paint only in a well-ventilated area. The accessory must always be used in accordance with the Manufacturer s instructions and safety regulations’.
• Some paints and other materials are combustible when sprayed and should not therefore be sprayed close to flames or any heat source or any areas where sparks may occur. If in doubt about the safe use of materials, please consult the Manufacturer before use.
  1. Connect the paint spray gun to the compressor as explained in chapter 3.
  2. Adjust working pressure to the value indicated for this accessory.
  3. Position the paint cup A and screw it into the socket B (fig. 1). Make sure that the paint cup is securely screwed into the socket, otherwise paint may leak during use.
  4.  Remove the lid C of paint cupA(fig. 2).
  5. The paint or the material to be sprayed can now be inserted in paint cupA.
  6. Replace paint cup lid C by securely pushing this into paint cupA(fig. 2).
  7. The spray pattern (horizontal or vertical spraying) can be adjusted by loosening ring D and turning nozzle E and then retightening ring D (fig. 3).
  8. The width of the spray pattern can be adjusted by rotating the adjustment knob F (fig. 3).
  9. The volume of paint/material sprayed can be adjusted by reducing or increasing the stroke of trigger G, turning the adjustment knob H (fig. 3).
  10. To operate the paint spray gun, pull trigger G (fig. 3). Pulling the trigger half way, compressed air only is passed through nozzle E. This facility is useful when you have fi nished painting and want to clean the gun. Pulling trigger G so that it is fully engaged, material is introduced in the gun and spray painting can begin.
  11. During spraying, release the vent valve I of paint cupA(fig. 4).
• Before using the spray gun practice on a test material in order to establish the correct pattern of spray and the correct quantity of material to be applied
  The air spray gun is equipped with a painting tank, a regulator of the paint quantity (1), a regulator of the air flow (2) and a regulator of the spraying mode (3).

Never exceed the recommended air pressure.

• The paint or material to be sprayed may require thinning. The thinning fluid and dilution formula should be obtained from the Manufacturer./Paint material that is too thick may block the nozzle on the spray gun preventing use,.
• When filling the paint cup with paint material/,maintain the spray gun in a vertical position to avoid spillage

Maintenance spray gun:

• After use, the paint spray gun must be cleaned thoroughly.
• After disposing of any material not used, add a small quantity of paint thinner to paint cupAand use the spray paint gun again as during spraying, fully pressing trigger G and complying with the same safety precautions. This operation permits initial cleaning of the fluid ducts.
• To clean, unscrew nozzle D and ring E (fig. 5).
• Disassemble the spraying needle by unscrewing knob H and extracting spring L and needle M (fig. 6).
• Lubricate the socket of the spraying needle N at regular intervals (fig. 6).
• Thoroughly clean these items with a suitable product.
• Also clean the fluid passage through the socket of paint cupA(fig. 1).

Air blow gun

1. Connect the air blow gun to the compressor as explained in chapter 3.
2. Adjust working pressure to the value indicated for this accessory.
3. To use the air blow gun, press lever D and direct the nozzle B towards the surface to be cleaned figures 1-2
   Clean the carpets of your home or car mats very efficiently using the blow gun. It is also ideal for keyboards electrical items refrigerators,,cameras TV cameras,glassware and,vacuum cleaners.

 Inflation gun

1. Connect the inflation gun to the compressor, as explained in chapter 3.

2. When inflating car tires or certain bicycle tires, it is not necessary to insert any of the adapters (fig. 2). Press tab A and connect the hose to the tire pushing the fitting on the valve (fig. 3) and then releasing the tab.

3. Regulate working pressure to the value indicated for this accessory.

4. Inflate the tire pressing lever B until the inflation pressure required, indicated on gauge C, is reached (figures 1-3). In the case of over-inflation, press button D to reduce inflation pressure figures 1-3).

5. When inflating footballs, rubber dinghies, certain bicycle tires and children’s inflatable swimming pools, you may have to use a suitable adapter (fig. 2).

   • Adapter E is used for footballs
   • Adapter F is used for rubber dinghies, air beds and children’s swimming-pools
   • Adapter Gis used for certain bicycles
     Select the suitable adapter and insert it in the inflation hose pressing tab A (fig. 4). Push the adapter in the inflation hose a shown in figure 5 and release tab A. To fasten the adapter, turn it slightly in a clockwise direction.

6. Inflate the object required as described in point 4 above.

Washing spray gun

• Always wear safety gloves and shoes when using the washing spray gun. When using possibly flammable chemical products, never direct the jet of the gun close to flames, towards any source of heat or anywhere whereaspark may be struck.

  1. Connect the washing spray gun to the compressor as explained in chapter 3.
  2. Adjust working pressure to the value indicated for this accessory.
  3. Unscrew cup Afrom the body of the gun B (fig. 1). Pour in the chemical product you intend to use and refasten cup A to the body of the gun B (fig. 1).
  4. To use the accessory, press lever C (fig.2).
  5. To adjust the jet, turn nozzle D which is secured by ring-nut E (fig. 3).
     The material to be sprayed may have to be diluted. The dilution formula should be obtained from the Manufacturer. If the product is too dense, it may block the nozzle, preventing use.

• When filling the cup with the material used for washing, keep this in a vertical position to avoid spillage.
  The washing spray gun is also very useful for spraying disinfectants, insecticides and plant-care products.

Transport& storage

• After use, always store the washing spray gun in a dry, clean environment. Do not use solvents, flammable or toxic liquids to clean the gun.
• Before storage, the air spray gun should be disassembled and cleaned thoroughly from the remnant sprayed Iiquids. While transporting and storing the air spray gun, try not to expose it to moisture. It’s recommended that you keep the tool in a dry cool place with proper ventilation and avoid high humidity, corrosive gases and dust. After unpacking we recommend to pack the tool again if you intend to transport it to working place or for storage.

Warranty

• Warranty refer to defects of materials and components and do not refer to components subject to natural wear and maintenance work.
• Only machines cleaned from dust and dirt in original factory packing fully completed, provided with instruction manual, warranty card with fixed sales date with a shop stamp factory serial number and originals of sales and ware receipt issued by salesman are subjects of warranty. Within the warranty period the service center eliminate free of charge all detected production defects. The manufacturer disclaims warranty and legal responsibilities if nonobservance of the instruction manual by user, unqualified disassembling repair or maintenance of the machine as well does not bear responsibility for caused injury to persons or damages.

ABOUT COMPANY

• Topayas nMHWA FUBAG
• TEL.: (495) 641-31-31
• info@fubag.ru
• www.fubag.ru

References

• Фирменный интернет-магазин FUBAG - сварочное, садовое и автогаражное оборудование, пневмоинструмент и камнерезные станки купить в Москве с доставкой по России

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>