FORTRESS 64592 1 Gallon 135 PSI Ultra Quiet Hand Carry Jobsite Air Compressor Owner’s Manual

June 6, 2024
FORTRESS

Fortress Logo

FORTRESS 64592 1 Gallon 135 PSI Ultra Quiet Hand Carry Jobsite Air

Compressor

FORTRESS 64592 1 Gallon 135 PSI Ultra Quiet Hand Carry Jobsite Air
Compressor

IMPORTANT SAFETY INFORMATION

General Safety Warnings
  1. Work area safety

    • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
    • Do not operate the Compressor in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Compressor motors produce sparks which may ignite the dust or fumes.
    • Keep children and bystanders away from an operating compressor.
  2. Electrical safety

    • Compressor plugs must match the outlet. Never modify the plug in any way.
    • Do not use any adapter plugs with grounded compressors. Standard plugs and matching outlets will reduce risk of electric shock.
    • Do not expose compressor to rain or wet conditions. Water entering a compressor will increase the risk of electric shock.
    • Do not abuse the cord. Never use the cord for unplugging the compressor.
      Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  3. Personal safety

    • Stay alert, watch what you are doing and use common sense when operating this compressor. Do not use this compressor while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a compressor may result in serious personal injury.

    • Use personal protective equipment.
      Always wear ANSI-approved eye protection during setup and use.

    • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source or moving the compressor.

  4. Compressor use and care

    • Do not use the compressor if the switch does not turn it on and off. Any compressor that cannot be controlled with the switch is dangerous and must be repaired.
    • Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the compressor. Such preventive safety measures reduce the risk of starting the compressor accidentally.
    • Store an idle compressor out of the reach of children and do not allow persons unfamiliar with the compressor or these instructions to operate it. A compressor is dangerous in the hands of untrained users.
    • Maintain the compressor. Keep the compressor clean for better and safer performance. Follow instructions for lubricating and changing accessories. Keep dry, clean and free from oil and grease. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the compressor’s operation. If damaged, have the compressor repaired before use. Many accidents are caused by a poorly maintained compressor.
    • Use the compressor in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the compressor for operations different from those intended could result in a hazardous situation.
  5. Service

    • Have your compressor serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the compressor is maintained.
Air Compressor Safety Warnings
  1. Risk of fire or explosion – do not spray flammable liquid in a confined area or towards a hot surface. Spray area must be well-ventilated. Do not smoke while spraying or spray where spark or flame is present. Arcing parts – keep compressor at least 20 feet away from explosive vapors, such as when spraying with a spray gun.

  2. Risk of bursting – do not adjust regulator higher than marked maximum pressure of attachment.

  3. Risk of injury – do not direct air stream at people or animals.

  4. Do not use to supply breathing air.

  5. Do not leave compressor unattended for an extended period while plugged in. Unplug compressor after working.

  6. Keep compressor well-ventilated. Do not cover compressor during use.

  7. Drain Tank daily and after use. Internal rust causes tank failure and explosion.

  8. Do not remove the valve cover or adjust internal components.

  9. Compressor head gets hot during operation.
    Do not touch it or allow children nearby during or immediately following operation.

  10. Do not use the air hose to move the compressor.

  11. Release the pressure in the storage tank before moving.

  12. The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons.

  13. All air line components, including hoses, pipe, connectors, filters, etc., must be rated for a minimum working pressure of 150 PSI, or 150% of the maximum system pressure, whichever is greater.

  14. USE OF AN EXTENSION CORD IS NOT RECOMMENDED. If you choose to use an extension cord, use the following guidelines:

TABLE A: RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT)


NAMEPLATE AMPERES (at full load)

| EXTENSION CORD LENGTH
25′| 50′| 10′|

150′

0 – 6

| 18| 16| 16| 14
6.1 – 10| 18| 16|

Do not use.

10.1 – 12

| 16| 16| Do not use.
12.1 – 16| 14| 12|

Do not use.

  • Make sure your extension cord is in good condition.
  • Be sure to use an extension cord which is heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
  1. Industrial applications must follow OSHA guidelines.

  2. Maintain labels and nameplates on the compressor. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

  3. This product is not a toy.
    Keep it out of reach of children.

  4. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.

Grounding

110-120 VAC Grounded Compressors: Compressors with Three Prong Plugs

  1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This compressor is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

  2. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

  3. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor.
    If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

  4. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded.

  5. Use only 3-wire extension cords that have 3- prong grounding plugs and 3-pole receptacles that accept the compressor’s plug.

  6. Repair or replace damaged or worn cord immediately.
    Compressors with Three Prong Plugs

  7. This compressor is intended for use on a circuit that has an outlet that looks like the one illustrated above in 125 VAC 3-Prong Plug and Outlet. The compressor has a grounding plug that looks like the plug illustrated above in 125 VAC 3-Prong Plug and Outlet.

  8. The outlet must be properly installed and grounded in accordance with all codes and ordinances.

  9. Do not use an adapter to connect this compressor to a different outlet.

Specifications

| 64592 – 1 Gallon|

64596 – 2 Gallon

---|---|---

Electrical Rating

| 120VAC / 60Hz / 3A| 120VAC / 60Hz / 7A
Air Outlet Size| 1/4″ – 18 NPT|

1/4″ – 18 NPT

Air Pressure

| Shut-off| 135 PSI| 135 PSI
Restart| 105 PSI|

105 PSI

Air Tank Capacity

| 1 Gallon| 2 Gallons
Air Flow Capacity| 0.7 SCFM @ 90 PSI|

2.1 SCFM @ 90 PSI

Sound Level

| 57 dBA|

60 dBA

Installation

Functions

Functions

Breaking in the Air Compressor
  1. Turn Power Switch OFF and unplug Power Cord.
    Breaking in the Air Compressor 01

  2. Fully open Drain Valve.
    Breaking in the Air Compressor 02

  3. Plug in Power Cord.

  4. Turn Power Switch to AUTO.
    Breaking in the Air Compressor 03

  5. Let unit run for 30 minutes. Air will expel freely through the Drain Valve.

  6. Turn Power Switch OFF.

  7. Unplug Power Cord and close Drain Valve.

Operating Instructions

Air Compressor Area Set Up
  1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent injury.
  2. Locate the Air Compressor on a flat level surface to ensure proper pump lubrication and to prevent damage to the unit. Keep at least 12″ of space around the unit to allow air circulation.
  3. Route the power cord from the Air Compressor to the grounded wall outlet, along a safe path without creating a tripping hazard or exposing the power cord to possible damage.
Air Connection Setup
  1. Connect a 1/4″ NPT air hose (sold separately) to the Air Outlet. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.
  2. Consult air tool’s manual for needed accessories.
General Operation
  1. Close Drain Valve.
    General Operation 01

  2. Close Regulator.
    General Operation 02

  3. Plug Power Cord into a grounded 120VAC electrical outlet.

  4. Turn Power Switch to AUTO.

  5. Allow Air Compressor to build up pressure until it cycles off.
    Note: At the beginning of the day’s first use of the Air Compressor, check for air leaks by applying soapy water to connections while the Air Compressor is pumping and after pressure cut-out. Look for air bubbles. If air bubbles are present at connections, tighten connections. Do not use the Air Compressor unless all connections are air tight, the extra air leaking out will cause the Air Compressor to operate too often, increasing wear on the Air Compressor.
    Note: As long as the Power Switch is set to AUTO, the operation of the Air Compressor is automatic, controlled by an internal pressure switch. The Air Compressor will turn on automatically when the air pressure drops to 105 PSI, and will turn off automatically when the air pressure reaches 135 PSI.

  6. Make sure the air tool’s throttle or switch is in the OFF position. Connect the air tool to the air hose.

  7. Adjust the Regulator Knob so that the air output is enough to properly power the tool, but the output will not exceed the tool’s maximum air pressure at any time. Turn the knob clockwise to increase the pressure and counter-clockwise to decrease pressure. Adjust the pressure gradually, while checking the Outlet Pressure gauge to set the pressure.

  8. Use the air tool as needed.

  9. When finished, turn the Power Switch OFF.

  10. Unplug the Air Compressor.

  11. Bleed air from the tool then disconnect the tool.

  12. Open the tank’s Drain Valve slowly to gradually release tank pressure and any built-up moisture. Close the Drain after air and moisture have drained out. Do not remove the Drain Valve.

  13. Clean, then store the Air Compressor indoors.

Emergency Depressurization

If it is necessary to quickly depressurize the Air Compressor, turn the Power Switch OFF. Then, pull on the ring on the Safety Valve to quickly release stored air pressure.

Emergency Depressurization

Automatic Shut off System
  1. If the Air Compressor automatically shuts off before reaching its normal cutoff pressure:
    • Shut off all tools.
    • Turn Power Switch to OFF position.
    • Unplug Air Compressor.
    • Wait until the Air Compressor cools down (about 10 minutes).
    • 64592 – 1 Gallon
    • Push Reset Button.
    • Plug Air Compressor in.
    • Turn Power Switch to AUTO.
    • 64596 – 2 Gallon
    • Plug Air Compressor in.
    • Turn Power Switch to AUTO.
    • Resume operation.
  2. Possible causes of repeated automatic shut off of the Air Compressor are:
    • Using an extension cord that is too long or narrow;
    • An air leak or open hose causing the Air Compressor to cycle too often and build up heat;
    • Turning Air Compressor off and on again too quickly.
  3. Correct any issues before further use to avoid damage to the Air Compressor.

Maintenance and Servicing

Cleaning, Maintenance, and Lubrication
  1. BEFORE EACH USE, inspect the general condition of the air Air Compressor. Check for:

    • loose hardware,
    • misalignment or binding of moving parts,
    • cracked or broken parts,
    • damaged electrical wiring, and
    • any other condition that may affect its safe operation.
  2. AFTER USE, wipe external surfaces of the
    Air Compressor with a clean cloth.

  3. WARNING! TO PREVENT SERIOUS INJURY: If the supply cord of this Air Compressor is damaged, it must be replaced only by a qualified service technician.

Maintenance Schedule

Following are general guidelines for maintenance checks of the Air Compressor.
Note: The environment in which the Air Compressor is used, and the frequency of use will affect how often you will need to check the Air Compressor components and perform maintenance procedures.

Daily:

  • Make sure all nuts and bolts are tight.
  • Drain moisture from air tank.
  • Check for abnormal noise or vibration.
  • Check for air leaks.*
  • Wipe off any oil or dirt from the Air Compressor.

Weekly:

  • Inspect Air Filter.

Monthly:

  • Inspect Safety Valve.
Draining Moisture from Air Tank

The Moisture Drain is located under the Tank. It must be used daily to release all trapped air and moisture from the Tank. Doing this will eliminate condensation and prevent tank corrosion.

  1. Turn the Power Switch off.
  2. Turn the Drain Valve to open it.
  3. When all the pressure and moisture is released, close the Moisture Drain.
Air Filter Maintenance
  1. Remove Cover and Filter. Check Filter for accumulated dirt.

  2. Cleaning:

    • To prevent injury from dust and debris, wear ANSI-approved safety goggles, NIOSH-approved dust mask/respirator, and heavy-duty work gloves. In a well-ventilated area away from bystanders, use pressurized air (no more than 15 PSI) to blow dust out of the filter.
    • Replace the clean filter. Replace the Cover, making sure the Tube is facing down.
  3. Replacements:

    • Air Inlet Filter only:
      Paper Filter Element 2-1/4″ Outer Diameter.

    • Air Inlet Filter Assembly:
      Inlet Filter Silencer Male 1/4″ NPT.

Troubleshooting

Problem

| Possible Causes|

Likely Solutions

---|---|---
Compressor does not start or restart|

  1. Tank(s) already pressurized.
  2. Power cord not plugged in properly.
  3. Incorrect power supply.
  4. No power at outlet.
  5. Thermal overload switch tripped.
  6. Building power supply circuit tripped or blown fuse.
  7. Cord wire size is too small or cord is too long to properly power compressor.
  8. Compressor needs service.

|

  1. No problem. Compressor will start when needed.
  2. Check that cord is plugged in securely.
  3. Check that circuit matches compressor requirements.
  4. Reset circuit breaker, or have outlet serviced by a qualified technician.
  5. Turn off Compressor and wait for it to cool down. Press reset button. Resume operation.
  6. Reset circuit or replace fuse. Check for low voltage conditions. It may be necessary to disconnect other electrical appliances from the circuit or move the compressor to its own circuit.
  7. Use larger diameter or shorter extension cord or eliminate extension cord. See Recommended Wire Gauge for Extension Cords in Safety section.
  8. Have unit inspected by a qualified technician.

Compressor builds pressure too slowly|

  1. Incorrect power supply.
  2. Working environment too cold.
  3. Safety valve leaking.
  4. Loose fittings.

|

  1. Check that circuit matches compressor requirements.

  2. Move compressor to a warmer location.

  3. Listen for air leaking from valve.
    If leaking, replace with identical valve with same rating.
    DO NOT SEAL OR TAMPER WITH SAFETY VALVE.

  4. Reduce air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.

Compressor not building enough air pressure|

  1. Air filter needs cleaning / replacing.
  2. Check Valve needs service.
  3. Compressor not large enough for job.
  4. Loose fittings.
  5. Hose or hose connections too narrow.
  6. High altitude reducing air output.

|

  1. Check inlet filter.
    Clean and/or replace as needed.

  2. Have technician clean or replace, as needed.

  3. Check if accessory CFM is met by Compressor.
    If Compressor cannot supply enough air flow (CFM), use a larger Compressor.

  4. Reduce air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.

  5. Replace with wider hose and/or hose connections.

  6. Higher altitudes require compressors with greater output.

Overheating|

  1. Air filter needs cleaning / replacing.
  2. Unusually dusty environment.
  3. Extension cord used.

|

  1. Check inlet filter. Clean and/or replace as needed.
  2. Clean and/or replace filter more often or move unit to cleaner environment.
  3. Eliminate extension cord.

Compressor starts and stops excessively|

  1. Loose fittings.
  2. Compressor not large enough for job.

|

  1. Reduce air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.
  2. Check if accessory SCFM is met by Compressor. If Compressor cannot supply enough air flow (SCFM), use a larger Compressor.

Excessive noise| Loose fittings.| Reduce air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.
Moisture in discharge air| Too much moisture in air.| Install inline air filter/dryer, and/or relocate to less humid environment.
Safety Valve “pops”| Safety valve needs service.| Pull on the ring on the Safety Valve. If it still pops, replace.
Air leaks from pump or fittings| Loose fittings.| Reduce air pressure, then check all fittings with a soap solution for air leaks and tighten as needed. Do not overtighten.
Air leaks from tank| Defective or rusted tank.| Have tank replaced by a qualified technician.
Drain moisture from tank daily to prevent future corrosion.
Follow all safety precautions whenever diagnosing or servicing the compressor. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

64592 Parts List

Part

|

Description

---|---

1

| Fan Housing

2

| Fan

3

| Bolt M5*125

4

| Spring Washer Ø5

5

| Washer Ø5

6

| Bolt M6*10

7

| Crank Shaft

8

| Bearing

9

| Cross Head Bolt M4*8

10

| Washer Φ4

11

| Crankcase

12

| Bolt M4*16

13

| Connecting Rod

14

| Piston Ring

15

| Press Cake

16

| Washer Φ6

17

| Bolt M6*16

18

| Cylinder

19

| Adjusting Pad

20

| Cylinder Seal

21

| Washer Φ4

22

| Reed Valve

23

| Valve Plate

24

| Reed Valve Block

25

| Bolt M4*5

26

| Cylinder Cap Seal

27

| Cylinder Cap

28

| Bolt M5*25

29

| Pump Cover Press Cake

30

| Pump Cover

31

| Cross Head Screw ST2.9*13

32

| Seal

33

| Air Tube

34

| Elbow

35

| Cylinder Cap

36

| Air Filter

37

| Fan

38

| Crankcase

39

| Rubber Cushion

40

| Washer

41

| Cross Head Bolt M4*12

42

| Nut M6

43

| Bearing

44

| Rotor Assembly

45

| Stator Assembly

46

| Cable Sheath

47

| Motor Sleeve

48

| Funnel

49

| Nut

50

| Pipe

51

| Washer

52

| Nut

53

| Sleeve

54

| Check Valve

55

| Inlet Pipe

56

| Handle Grip

57

| Tanks Assembly

58

| Drain Valve

59

| Straight Joint

60

| Pipe

61

| Nut

62

| Funnel

63

| Sleeve

64

| Elbow

65

| Bolt M6*14

66

| Nut M6

67

| Panel

68

| Coupler

69

| Pressure Gauge

70

| Pressure Regulator Assembly

71

| Safety Valve

72

| End Cap

73

| Bolt M6*16

74

| Washer Φ6

75

| Rubber Foot

76

| Thermal Protector

77

| Capacitor Pad

78

| Capacitor

79

| Cable Clip

80

| Capacitor Case

81

| Power Cord

82

| O-Ring Seal Φ15.5*2

83

| Nut

84

| Nut

85

| Pressure Switch

64592 Assembly Diagram

64592 Assembly Diagram

64596 Parts List

Part

| Description|

Qty

---|---|---

1

| Bolt M4*12|

8

2

| Washer Φ4|

8

3

| Fan Cover|

2

4

| Retainer Ring|

2

5

| Fan|

1

6

| Bolt M8*8|

4

7

| Crankshaft|

2

8

| Bearing|

2

9

| Nut M6|

2

10

| Connecting Rod|

2

11

| Bolt M6*30|

2

12

| Bolt M5*117|

4

13

| Spring Washer Ø5|

4

14

| Washer Φ5|

4

15

| Nut M4|

1

16

| Crankcase|

2

17

| Wire|

1

18

| Bearing|

2

19

| Thermal Protector|

1

20

| Stator Assembly|

1

21

| Rotor Assembly|

1

22

| Nut M5|

4

23

| Fan|

1

24

| Piston Ring|

2

25

| Press Cake|

2

26

| Washer Φ6|

16

27

| Bolt M6*16|

2

28

| Cylinder Gasket|

2

29

| Cylinder|

2

30

| Cylinder Seal|

2

31

| Bolt M4*6|

2

32

| Reed Valve|

4

33

| Valve Plate|

2

34

| Bolt M3*10|

4

35

| Washer Ø3|

4

36

| Cushion|

4

37

| Block Piece|

2

38

| Nut M3|

4

39

| Washer Φ4|

6

40

| Cross Head Bolt M4*8|

6

41

| Cylinder Cap Seal|

2

42

| Cylinder Cap|

1

43

| Spring Washer Ø6|

8

44

| Bolt M6*55|

8

45

| Easy Start Valve|

1

46

| Washer Φ13.5*Φ2|

4

47

| Air Tube|

2

48

| Cylinder Cap|

1

49

| Elbow|

1

50

| Cross Head Screw|

4

51

| Cylinder Cap Cover|

2

52

| Cylinder Cap Cover Lock Block|

2

53

| Bolt M4*12|

1

54

| Plug|

1

55

| Cable Clip|

5

56

| Cushion|

4

57

| Frame Assembly|

1

58

| Foot|

4

59

| Washer Φ6|

4

60

| Bolt M6*16|

4

61

| Nut M8|

4

62

| Nut M6|

4

63

| Locking Washer Φ6|

6

64

| Washer Φ6|

4

65

| Bolt M6*35|

4

66

| Tank Assembly|

1

67

| Drain Valve|

1

68

| Air Filter|

1

69

| Elbow|

1

70

| Sleeve|

2

71

| Funnel|

2

72

| Nut|

2

73

| Nylon Pipe|

1

74

| Inlet Pipe|

1

75

| Paper Gasket|

2

76

| Check Valve|

1

77

| Bushing|

2

78

| Funnel|

2

79

| Nut|

1

80

| Pipe|

1

81

| Nut|

1

82

| Pressure Switch|

1

83

| Joint|

1

84

| Power Line|

1

85

| Nut M6|

4

86

| Handle Grip|

1

87

| Joint|

1

88

| End Cap|

2

89

| Safety Valve|

1

90

| Coupler|

2

91

| Pressure Regulator Assembly|

1

92

| Pressure Gauge|

1

93

| Pressure Gauge|

1

94

| Panel|

1

95

| Bolt M6*16|

4

96

| Wire|

1

97

| Capacitor Case|

1

98

| Rubber End Cap|

1

99

| Capacitor|

1

100

| Seal Φ50.5*Φ2.5|

2

Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Parts may not be interchangeable. Specify number when ordering.

64596 Assembly Diagram

64596 Assembly Diagram 01

64596 Assembly Diagram 02

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

26541 Agoura Road
Calabasas, CA 91302
1-888-866-5797

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTRESS User Manuals

Related Manuals