Handy THPCS16 38CC Petrol Chainsaw User Manual
- June 6, 2024
- Handy
Table of Contents
THPCS16 38CC Petrol Chainsaw
-aTnM-
OPERATOR’S MANUAL AND PARTS LIST PETROL CHAINSAW – THPCS16
Sales & Helpline 01793 333220
www.thehandy.co.uk
Before use please read & understand this manual, paying particular
attention to the safety instructions.
Page 1
2010 vI
SAFETY INSTRUCTIONS
Read and understand the owner’s manual and labels affixed to the chainsaw.
Learn its application and limitations as well as the specific potential
hazards. Retain these instructions for reference.
· Use safety footwear, protective clothing and a helmet with eye and ear
protection.
· Do not operate the chainsaw if you are tired,ill or under the influence of
alcohol or drugs.
· Do not smoke when using the chainsaw and ensure caution when handling fuel.
We recommend you fuel the saw at least 3m away from where you wish to work in
case any spilt fuel ignites when starting the engine.
· Ensure that bystanders, children and pets keep well away when starting or
cutting – at least 10m.
· Inspect the chainsaw , and in particular the bar and chain, before use for
any worn or damaged parts. Do not use until the parts are repaired or
replaced.
· Before starting the engine make sure the chain is not in contact with
anything and have a clear work area and secure footing.
· Hold the chainsaw firmly with both hands when using and keep all parts of
your body away from the machine. Put the scabbard on for transportation.
· Always carry the chainsaw with the engine stopped, the bar and chain to the
rear and the muffler away from your body.
· Beware of small branches and saplings whipping back towards you as you cut.
When cutting a limb which is under tension, be alert to the possibility of the
limb springing back when the tension is released.
· Do not cut in high wind, bad weather or poor visibility. Check the tree for
dead branches which could fall during operation.
· NEVER operate the chainsaw in a tree unless you are specially trained to do
so.
Always shut off the engine before setting it down.
A word about KICKBACK Kickback can occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches the saw chain. Do
not rely solely on the safety devices built into your chainsaw.
· Keep a good grip on the saw with both hands – this will help you mantain
control should kickback occur.
· Ensure thatthe area in which you are cutting is clear and free from
obstructions so that the tip does not make contact with another log or
obstruction.
· Always cut at high engine speeds and do not overreach or cut above shoulder
height.
· Follow the manufacturer’s guidelines for sharpening and maintaining the
chain and only use replacement bars and chains specified. Page 3
WARNING SYMBOLS
,.jU
Oil and Fuel Mixture Position – Fuel Cap
~·
8~… 1’1 …
T CHOKE
..,W START RUN
H L T
0..
Chain Oil
Position – Oil Cap
On/Off Switch. Setting to “0” position stops the engine immediately.
Position – Rear left of the unit. Starting the Engine. Follow instructions in
handbook (OPERATION) for cold and warm starting
Position – Upper right of air cleaner cover
High Speed Adjustment Screw Slow Speed Adjustment Screw Idle Adjustment Screw
Position -Left Side of Rear Handle Direction of Release of Chain Brake.
= White Arrow Released = Black Arrow Activated.
Position – Front of Chain Cover
SPECIFICATIONS
Disolacement (ern”) Fuel Mixture Fuel Tank Canacitvtml) Chain Oil Oil Tank
Caoacitv (rnl) Carburettor lonitlon Svstem Soark Plua Oil Feedlnq SYstem
Sorocket (Teeth & Pitch) Dimensions (LxWxH) Drv Weiaht (Power Unit) Guide Bar
Chain Pitch Gauoe
37.2 25:1 310 Soecialist Chain Oil 210 Dlaphracrn (Walbro WT) Electronic M7
Automatic Pump 6Tx%” 370x235x270 4.15ka Sprocket Nose – 14″/35cm Oreoon 91VG
%”/9.53mm 0.05″/1.27mm
Page 4
· Wearing gloves locate the guide bar onto the chainsaw making sure that the
hole on either side of the slot locates over the adjuster pin.
Note: A new chain will stretch during its first use. Turn off the engine then
check and readjust the chain frequently.
· Use a ratio of 25:1 unleaded petrol to 2-stroke mineral oil. For semi-
synthetic or synthetic use the manufacturer’s ratio. Mix in an appropriate
mixing bot-
Switch
Throttle lever
Throttle interlock
Chain oil
L needle
H needle
Idle adjusting screw
Cylinder cover “Sunshine”mark “Snow”mark
Felling direction Notch cut
Felling cut
Oiling port
Oiling port Grease port
Sprocket
Fuel filter
0.6 ~ 0.7 mm
Oil filter
Make the shoulder round
91VG.025″(0.64 mm)
Cutter length Filing angle Side plate angle Top plate cutting angle
Ruler Gap
No gap Chain tilts
PARTS DIAGRAM AND LIST
(
I
I/ I” /
1/i 112
No Part No Description
Qty No Part No Description
Qty
1
TH159-1 Nut Muffler
2
2
TH159-2 Muffler Assy
1
3
TH159-3 Gasket
1
4
TH159-4 Stud
2
5
TH159-5 Screw
4
6
TH159-6 Cylinder
1
7
TH159-7 Spark Plug
1
8
TH159-8 Gasket
1
13
TH159-13 Gasket
1
14 TH159-14 Boot Intake
1
15
TH159-15 Gasket
1
16 TH159-16 Carburettor
1
17
TH159-17 Screw
1
18 TH159-18 Grommet, inner
1
19
TH159-19 Washer Air Filter
1
20 TH159-20 Screw
2
21
TH159-21 Screw
4
22 TH159-22 Support,Speed Adjust 1
23
TH159-23 Top Cover
1
24 TH159-24 Choke Knob
1
25
TH159-25 Support,Choke Knob 1
28 TH159-28 Air Filter
1
29
TH159-29 Air Filter Cover
1
30 TH159-30 Air Filter Knob
1
34
TH159-34 Washer Clutch
1
35 TH159-35 Sprocket
1
36
TH159-36 Bearing Needle
1
37 TH159-37 Gear Worm
1
38
TH159-38 Screw
2
39 TH159-39 Cover,Oil Pump
1
40
TH159-40 Screw
2
41 TH159-41 Oil Pump
1
42
TH159-42 Hose Oil Outlet
1
43 TH159-43 Washer Oil Pump
1
44
TH159-44 Large Oil Seal
1
45 TH159-45 Ring
1
46
TH159-46 Screw
1
47 TH159-47 Chain Catcher
1
48
TH159-48 Stud
2
49 TH159-49 Fuel Injection Nozzle 1
50
TH159-50 Screw,crankcase
4
51 TH159-51 Right Crankcase
1
Page 12
EC Declaration of Conformity
Declaration of conformity
Pursuant to the regulations of the following EC Directives:
Electromegnetic Competibility Directive 2004l108lEC Machinery Directive
2006/42/EC Noise Directive 2000/141EC
Handy Distribution Ltd hereby declares that the product: Machine type: Petrol Chain Saw Machine model: THPCS16 Engine displacement: 37.2cm3 Power: 1.2kW Cutting length: 380mm Max speed: 10,OOO/min Mass in kg: 6.0kg
Conforms to the main safety requirements of the EC Directives listed above. This conformity is based on the following standards and normative documents:
EN ISO 11681-1:2008 EK9 2007-18:2007-05-31 EN 15014982:1998
The conformity assessment procedure followed was in according with Annex III of the Directive 2000/14/EC.
Calculated Sound Power Level: 106.6 dB (A) K=3.4 dB (A) Guaranteed Sound Power Level: 113 dB (A)
The responsible person, based within the EC, is identified below Name: Mr. Simon Belcher Title: Managing Director Company: Handy Distribution Ltd Address: Hobley Drive, Stratton St Margaret, Swindon, Wiltshire, SN34NS
Signature :
Date: 15thAug 2010
Page 14
To order spare parts and see the complete range of garden machinery and garden
equipment from Handy, visit:
www.thehandy.co.uk
Spares & Support: 01793 333212
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>