Handy 10369 Electric Drill Grinder Polisher Set Instruction Manual
- June 6, 2024
- Handy
Table of Contents
Handy 10369 Electric Drill Grinder Polisher Set
EN – 10369 – Electric drill, grinder, polisher set
The HANDY DRILL sanding, engraving and drilling machine has been specially
developed for home, manicure / pedicure and DIY purposes. Thanks to the built-
in battery, you can use the tool anywhere without cables. You can use it to
drill small holes, polish, engrave or even cut. It can be ideal for removing
burred edges. Maximum shaft diameter Ø3.2 mm. The various chucks can be
connected easily and quickly. Thanks to its compact size and weight, the tool
is easy to handle, even in hard-to-reach places. It can also be suitable for
precise machining of wood, metal and plastic.
Use
Hold the device as if you were holding a writing instrument. Be careful not to
press the chuck lock button (B) during operation , as this may damage the
device. The switch (C) on the end of the appliance can be used to switch the
appliance on and off. Before connecting to the mains, make sure that the power
button is in the “0” position. To avoid dangerous situations, only connect the
device to a power source when it is set this way!
Change of accessories
- Turn off the device and make sure it is completely stopped. (For the higher security and to avoid the injuries remove the power cable from the wall socket!)
- Push and hold the collet lock (B) button and turn the collet until the button descends!
- When the collet has locked, turn the collet closing cap (A) and remove the accessory/head.
- Place the new accessory or head onto the collet and screw the closing cap to close, while the LOCK BUTTON is held all time.
- Release the LOCK BUTTON!
Accessories
- Clamping head (chuck)
- Chuck lock button
- On / Off switch
- Increase speed / Decrease speed
- Clamping heads
- DC Socket
ATTENTION!
- Always make sure that the charging cable and the device are intact before use.
- Do not use in humid environments, rain!
- Never use near flammable gases or liquids.
- Do not force the machine if you feel it slow down or stop, turn it off, orfinish the operation
- Never press the chuck lock button during operation!
- Wear protective clothing ( goggles , mask , gloves) during use.
- Do not touch the drill / grinder tip during operation, as this may cause injury!
- It is strictly forbidden to disassemble or modify the device! In the event of a malfunction, contact a specialist for repairs.
- Only charge the device with its own charging cable and adapter!
- Before connecting to the mains, always make sure that the adapter of the appliance is compatible with the voltage. The charging time of the device is 2-3 hours.
- Do not use the device while charging, to protect the battery, the device will not rotate the motor after connecting the cable!
- When the device’s battery is low, the battery charge LED lights up orange! In this case, stop using the tool and charge the tool battery.
Technical data
Adapter input voltage: 100 – 240 V AC, ~ 50/60 Hz
Adapter output voltage: 9 V DC, 500 mA
Battery : 16340, LI-ION, 7.4 V – 1100 mAh
Charging time : 2 – 3 hours
Operating time with one charge : up to 60 minutes Operating voltage: 7.4
V DC
Performance: 4.5 W
Power consumption: max . 500 mA
Battery cycle : 500
Idle speed: 5000 – 25,000 rpm
Chuck capacity: 1 – 3.2 mm
Max tool diameter (disc) : 35 mm DImensions: 210 x Ø40 mm Vibration: 1.55
m / s²
Noise pressure: max . 80 dB Contact protection class: III Protection:
IP20
Cable length: 175 cm
Color: Orange / Black
Weight: ~ 250 g
Material : Plastic
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>