Handy THKS16LTR-B 16L Knapsack Sprayer User Manual
- June 5, 2024
- Handy
Table of Contents
Handy THKS16LTR-B 16L Knapsack Sprayer
MAIN FUNCTION
ECONOMICAL, SAFE, AND LEAKPROOF, THIS SPRAYER CAN BE USED WITH ALL KINDS OF AGRICULTURAL CHEMICALS.
- WELDED CONTAINER
- PUMP AND AIR CHAMBER
- SPRAYING SYSTEM INCLUDING RUBBER HOSE, TRIGGER, SPRAYER SPINDLE AND SPRAY HEAD
- OPERATION ARM AND COMPONENTS
- BACKPACK SYSTEM
FEATURES
- THE CURVED BODY OF THE SPRAYER IS DESIGNED TO BE ERGONOMIC, COMPACT, AND SAFE.
- THE PUMP PRESSURISES THE SPRAYER QUICKLY AND EASILY.
- EASY TO USE LEAKPROOF SWITCH. THE SPRAYER CAN BE SET TO EITHER CONTINUOUS SPRAY OR SPOT SPRAY ALLOWING FOR DIFFERENT USES AND SAVING WATER BY USING THE APPROPRIATE SETTING.
- THE RESILIENT SPRAYER BODY IS RESISTANT TO ACIDITY AND WEAR AND IS WELL SEALED.
- THE SPRAYER CAN BE EQUIPPED WITH DIFFERENT SPRAYING COMPONENTS SUCH AS A SECTOR SPRAY HEAD OR HOLLOW CONICAL SPRAY HEAD AND AN ADJUSTABLE SPRAY HEAD FOR DIFFERENT USES AND DISTANCES.
ASSEMBLY
- FIG 1. INSERT THE ROCKER BAR FIXER AS SHOWN ON TO THE TOP OF THE AIR COMPARTMENT.
- INSERT THE ROD THROUGH THE ROCKER BAR FIXER AND THE TOP OF THE AIR COMPARTMENT.
- INSERT THE COTTER PIN THROUGH THE HOLE IN THE ROD.
- FIG 2. CONNECT THE ROCKER BAR FIXTURE TO THE ROD AS SHOWN.
- FIG 3. CONNECT THE ROCKER ROD TO THE ROD AND THE BOTTOM OF THE WATER TANK.
- FIG 4. LOOP THE ROCKER LOOP OVER THE ROCKER BAR.
- FIG 5. CONNECT THE HOSE CONNECTOR NUT TO THE TOP OF THE AIR COMPARTMENT AS SHOWN.
- FIG 6. CLIP THE LANCE TO THE RUBBER BAR FIXER.
INSTALLATION OF THE SPRAYER
INSTALL THE SPRAYER ACCORDING TO THE DRAWING BELOW STEP BY STEP
PLEASE NOTE THE PRESSURE LEVER CAN BE ASSEMBLED ON THE OTHER SIDE OF THE SPRAYER. TO DO THIS REMOVE THE SPLIT PIN THAT HOLDS THE ROCKER BAR IN PLACE, THEN REMOVE THE BAR AND INSERT IT INTO THE OTHER SIDE OF THE SPRAYER. REASSEMBLE THE SPLIT PIN AND BAR FIXER AS THEY WERE BEFORE. NOW ADJUST THE CARRYING STRAP, YOU MAY WANT TO CONNECT IT TO THE OTHER SIDE OF THE SPRAYER.
OPERATION
OPEN THE CAP OF THE CONTAINER, AND POUR THE LIQUID INTO THE CONTAINER SLOWLY. CLOSE THE CONTAINER TIGHTLY AND LIFT THE SPRAYER ONTO YOUR BACK. PUSH THE LEVER FOR THE PUMP UP AND DOWN AND WHEN THE PRESSURE IN THE AIR CHAMBER INCREASES PRESS THE LEVER AND BEGIN TO SPRAY. WHEN YOU HAVE FINISHED SPRAYING ALWAYS EMPTY THE CONTAINER COMPLETELY. REINSTALL THE SPRAYER AS PER THE INSTRUCTION SHEET SHOWN IN THE ABOVE DIAGRAM.
SAFETY MEASURES
- THE USER MUST WEAR A MASK AND GLOVES WHEN SPRAYING. AVOID CHEMICAL CONTACT FROM SKIN AND WASH IMMEDIATELY IF THIS HAPPENS
- NEVER SPRAY FACING INTO THE WIND CHOOSE THE SPRAY HEAD AND THE SPRAYING METHOD FOR THE CORRECT USE.
THE CHARACTERISTICS AND USAGE OF VARIOUS SPRAY HEADS
SECTOR SPRAY HEAD
THE SPRAY IS EVEN, WHICH IS MAINLY USED IN SPRAYING THE WEEDS IN SOIL
TREATMENT AND PLANT TREATMENT. IT CAN ALSO BE USED IN INSECTICIDES TO PREVENT
DISEASES AND KILL INSECTS DURING THE PERIOD OF SEEDLINGS. WHEN SPRAYING THE
LIQUID THE DISTANCE BETWEEN THE SPRAY HEAD AND THE GROUND SHOULD BE ABOUT 50CM
OR ABOVE THE TOP OF THE PLANT (WEED) BY 42CM. SPRAY IN THE SAME DIRECTION AS
THE WIND. KEEP THE SPRAY HEAD MOUTH PLUMB WITH THE SPRAY SPINDLE. TAKE THE
SPRAY SPINDLE AT ONE SIDE OF THE BODY AND KEEP SOME DISTANCE BETWEEN YOURSELF
AND THE SPRAY HEAD TO AVOID TOUCHING THE AREA BEING SPRAYED. WALK IN A
STRAIGHT LINE WHERE POSSIBLE.
CONICAL SPRAY HEAD
IT CAN BE USED TO SPRAY INSECTICIDES ETC BUT NOT TO BE USED FOR WEEDS. IT IS
APPROPRIATE FOR PREVENTING DISEASES AND KILLING INSECTS IN EVERY GROWTH PERIOD
OF PLANTS. SOME DISTANCE SHOULD BE KEPT BETWEEN THE SPRAY HEAD AND THE PLANTS
WHEN SPRAYING IN ORDER TO AVOID UNEVEN DISTRIBUTION. THE USER SHOULD SPRAY
LATERALLY IN THE SAME DIRECTION AS THE WIND IN A ZIG-ZAG PATH TO KEEP THE USER
IN A SAFE AREA
ADJUSTABLE SPRAY HEAD
DEPENDING UPON THE JOB THE USER CAN ADJUST THE SPRAY HEAD TO CHANGE THE ANGLE
AND THE DISTANCE OF THE SPRAY. THE GREATER THE ANGLE OF THE SPRAYER THE LARGER
DROPLETS WILL BE. AT GREATER ANGLES THERE WILL BE LESS MIST AND THE SPRAYER
WILL EMIT A COLUMN OF LIQUID, THIS IS MAINLY USED FOR WEED SPRAYING OR FOR
PREVENTING DISEASES AND KILLING INSECTS AT THE ROOTS OF THE PLANT
SPECIFICATIONS
- TYPE: BACKPACK
- CONTAINER CAPACITY: 16 LITRES
- OPERATION PRESSURE: 0.2-0.4 MPA
- OPERATION TRAVEL: 60-80 MM
- BOWL DIAMETER: 45MM
- NET WEIGHT: 3.2KG
TROUBLESHOOTING
MAINTENANCE
CLEAN THE SPRAYER AS PER DRAWING BELOW AS SOON AS IT HAS BEEN USED. THE USER
SHOULD CLEAN MORE CAREFULLY ESPECIALLY AFTER WEED KILLER SPRAYING. ADD SOME
WASHING POWDER OR SODA WHEN CLEANING. AFTER SPRAYING WEED KILLER IT IS BEST TO
CLEAN THE SPRAYER REPEATEDLY AS IT IS DIFFICULT TO KEEP THE SPRAYER CLEAN FROM
USING WEED KILLING AND PESTICIDES AND THEN USING THE SPRAYER AS A FERTILISER
SPRAYER. B: PLEASE DO NOT OPERATE ROUGHLY WHEN SPRAYING AS TO AVOID DAMAGE TO
THE SPRAYER. C: EXCEPTIONAL CHEMICAL LIQUID IS PROHIBITED TO BE USED. D:
PLEASE FOLLOW THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OF AGRICULTURAL
CHEMICALS WHEN SPRAYING.
REGULARLY LUBRICATE THE TREATED FELT SEALING WASHER OF THE AIR COMPARTMENT LID TO ENSURE SMOOTH OPERATION AND PREVENT LEAKS.
PARTS DIAGRAM
PARTS LIST AND DESCRIPTION
REF.| PART NO.| DESCRIPTION| REF.| PART NO.|
DESCRIPTION
---|---|---|---|---|---
1| TH189-1| ROCKER BAR FIXER| 17| TH189-17| ROCKER BAR FASTENER
2| TH189-2| ROCKER| 18| TH189-18| SPLIT
3| TH189-3| AIR COMPARTMENT| 19| TH189-19| BOTTOM CASE
4| TH189-4| SEAL VALVE| 20| TH189-20| CLIP
5| TH189-5| SEAL BALL| 21| TH189-21| FILTER SCREEN
6| TH189-6| O-RING| 22| TH189-22| SEALING WASHER
7| TH189-7| VALVE CAP| 23| TH189-23| MEDICAL CHEST LID
8| TH189-8| ROCKER BAR SLEEVE| 24| TH189-24| HOSE CONNECTOR NUT
9| TH189-9| SPLIT| 25| TH189-25| HOSE
10| TH189-10| ROD| 26| TH189-26| LANCE CONNECTOR NUT
11| TH189-11| ROCKER ROD| 27| TH189-27| CAP
12| TH189-12| PRESSURE LID OF AIR COMPARTMENT| 28| TH189-28| SWITCH
13| TH189-13| SEALING WASHER| 29| TH189-29| O-RING
14| TH189-14| AIR CHAMBER| 30| TH189-30| LANCE
15| TH189-15| O-RING| 31| TH189-31| O-RING
16| TH189-16| MEDICAL CHEST| 32| TH189-32| NOZZLE