MIBOXER Constant Voltage DMX512 & RDM Decoder User Manual

: June 6, 2024
: MiBOXER

Table of Contents

Features
Parameter
Function Settings
Dimming curve diagram
Connection diagram
Attention
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Subordinate New Brand
Constant Voltage DMX512 & RDM Decoder
Model No.: D1-CX / D2-CX / D3-CX / D4-CX / D5-CX

Features

Accord with DMX512 standard protocol.
Digital Display, Set DMX initial address through a button.
Support RDM function.
2000hz/500hz Output PWM frequency is optional.
Logarithm/Linear dimming curve is optional.
Anti-reverse protection function
Short circuit&Overcurrent protection and recovery function.
self-testing protection function when power on.

Parameter

Model No.	D1-CX	D2-CX	D3-CX	D4-CX	D5-CX
Output	20A/Channel	10A/Channel	6A/Channel	5A/Channel	4A/Channel
Total Output	Max 20A	Max 18A	Max 20A
Input Voltage	Common anode
Input Signal	-20~60°C
Connection	-20~60°C
Working Temp.	DC12~24V

Function Settings

1. Digital Display status description
Self-locking: Get into locking state when there is no operation over 30 seconds, digital display with low light or OFF.
Unlock Long press M button 2 seconds to make a digital display with high light, quit self-locking state.
The address is always ON: DMX signal valid.
Address flickering: DMX signal invalid.
Err: Short circuit/overcurrent protection; self-recover after 10 seconds.

2. DMX initial address setting
Under unlock status, when digital display shows 001-512( for example ), Short press ▲ button or ▼ button, you can change the DMX initial address; Long press, you can change it quickly.

For Example Set the Initial address to 100

D1-CX	D2-CX	D3-CX	D4-CX	D5-CX

Occupy 1 address
100| Occupy 2 address
100-101| Occupy 3 address
100-102| Occupy 4 address
100-103| Occupy 5 address
100-104

3. System Parameter Setting Instruction
Under unlock status: Long press M button 3 seconds to make the digital display show or , then get into system parameter setting. By this time, short press M button to switch 4 different parameter setting circularly.
Parameter 1: PWM frequency setting(show or ; Short press ▲ button or ▼ button to switch.
Set to PWM high-frequency output, 2000Hz. (Factory default parameter)
Set to PWM low-frequency output,500Hz.
Parameter 2: Dimming Curve setting(Show or ), short press ▲ button or ▼ button to switch.
Dimming curve is logarithm dimming. (Factory default parameter)
** Dimming curve is linear dimming.
Parameter 3: Dimming smoothness setting(show or ), short press ▲ button or ▼ button to switch.
** Smooth dimming. (Factory default setting)
Standard dimming.
Parameter 4: Digital display showing setting(show or ) short press ▲ button or ▼ button to switch.
Under self-locking status, the digital display is always ON (low lighting showing). (Factory default parameter)
Under self-locking status, digital display OFF.

Exit system mode: long press M button 1 second to exit. Or it will be self exit if there is no operation over 8 seconds.
4. Restore factory default.
Under unlock status, long press M button 10 seconds until digital display shows .

Dimming curve diagram

Connection diagram

Attention:

If the decoder is over 32pcs or using the super long signal cable, you need a DMX signal ampliﬁer. Amplify signal cannot be over 5 times.
If there is an overshoot effect due to the long signal cable or low-quality circuit, please connect 0.25W 90-120Ω terminal resistance at the end of each DMX signal cable.

Attention

This product should be debugged and installed by professionals.
Please check whether the output voltage of the power supply meets the requirements of the product voltage range.
The product is not waterproof, please install it in the waterproof box when installed outdoors.
Before switching on the power, please ensure that all wiring is correct, so as not to cause damage to the devices。
If a fault has occurred, non-professionals do not repair it without permission, otherwise, the devices will be damaged.

Made in China