YAESU M-90 MS Microphone Stand Kit User Manual
- June 6, 2024
- YAESU
Table of Contents
M-90 MS kit
MICROPHONE STAND KIT
Angle adjustment Screws
Attach the microphone body at the left and right pivots with the supplied
washers, lock washers, and screws. The angle of the microphone may be adjusted
by loosening the screws (turn them counterclockwise) on the left and right
sides of the microphone yoke. Place the microphone in the desired position and
then tighten the screws (turn them clockwise) to secure the microphone.
W3/8 Nut
Use the supplied nut (W3/8 Nut) to attach the yoke to a commercially available
desk arm type, or floor type microphone stand.
This kit requires a Commercially available microphone stand.
*** Microphone stand is not included.
Low-Cut switch**
Turns the low-cut filter (cut-off frequency 340Hz, -6dB/octave) ON or OFF.
Move the switch in the direction of the arrow to activate the low-cut filter.
PTT switch
When this switch is pressed, the transmit mode is set and held. When the
switch is pressed again the transceiver returns to receive mode.
***** An optional SCU-53 cable is required when connecting the M-90MS to an HF transceiver furnished with a round 8-pin microphone connector.
Example using the SCU-53 (optional)
As shown in the figure, route the optional SCU-53 cable behind the transceiver
leg to avoid interfering with transceiver operation.
This kit requires a commercially available microphone stand*.
***** Microphone stand is not included.
Using the M-90MS with Yaesu Transceivers
The M-90D operates with the below Transceivers.
FT-817/ND
FT-450/D
FT-950| FT-818ND
FT-900
FT-1000MP| FT-857/D
FT-991/A
FT-1000MP MARK-V| FT-891
FT-847
FTDX9000
FT-990
---|---|---|---
FTDX1200
FTDX101D
FT-747| FTDX3000D
FTDX101MP
FT-840| FTDX5000
FTDX10
FT-850| FT-897/D
FT-920
FT-2000/D
FT-1000*
- Requires Optional “Microphone Power Supply Kit”.
as of June, 2021
Safety Precautions (Be Sure to Read)
Be sure to read the safety precautions printed in the Operating Manual of the compatible transceiver to use this product safely.
Specifications
| Supply Voltage: | DC 5.0 V ±10 % |
|---|---|
| Current Consumption: | 15 mA (TYP) |
| Microphone Type: | Dynamic |
| Frequency Response: | 30 – 17000 Hz |
| Sensitivity: | -60 dB (1 kHz 0 dB=1V/Pa) |
| Microphone Impedance: | 600 Ohms |
| Dimensions: | Diameter: 2.45″ (62mm), Length: 6.38″ (162mm) |
***** Microphone head size only
Weight (approx):| 7.05 oz (200 g) w/ Bracket, w/o Handheld PTT Controller
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Disposal of Electrical and Electronic Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed of as
household waste.
Electronic and Electrical Equipment should be recycled at a facility capable
of handling these items and their waste by-products. Please contact a local
equipment supplier representative or service center for information about the
waste collection system in your country.
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa,
Shinagawa-ku, Tokyo 140-0002
Japan
EBC63X750 (2106N-AS)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>