EVA LOGIK ZW36 Z-Wave Plus Smart Light Dimmer Plug Instruction Manual
- June 6, 2024
- EVA LOGIK
Table of Contents
ZW36
Z-Wave Smart Plug
(1 channel)
Specifications:
Power: 120VAC, 60Hz
Loading: 10 Amp Max Smart Outlet
15 Amp Max Always-On Outlet
Total(Both Outlets): 15 Amp Max
Frequency: 908.42MHz
FCC ID: OXGZW36
IC: 10460A-ZW36
INTRODUCTION
The EVA LOGIK ZW36 is a Z-Wave enabled 15A receptacle designed for most
residential lighting and motor applications. It’s compatible with LED,
halogen, incandescent, xenon, fluorescent and compact fluorescent bulbs.The
ZW36 fully works with the Fibaro, Smartthings, Wink hub as well as all other
certified Z-Wave controllers.
Plug the light you want to control into the Z-Wave Smart plug-controlled
outlet.
NOTE: Plug directly into outlet, do not use with extension cords
One Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LED, fans or small appliances. Total load capacity for both outlets is 1800W (15A) Resistive.
Note : Your device may need to be within 100 feet of the controller to be
included. If so, include the device to the network within 10 feet of the
controller and relocate it to the desired position in your home. Be sure to
refresh the network if the device is included in this manner.
Add to Z-Wave Network
Put the Z-wave interface controller into “Add” mode, triple press the Program
button.
It will be included to the network. (Once your controller confirmed, refresh
the Z-Wave network to optimize performance. )
Remove from Z-Wave Network
Put the Z-Wave interface controller into “Remove” mode, triple press the
Program button. It will be excluded to the network.
To return your switch to factory defaults
Manual: Click the button 2 times quickly, and hold for at least 10 seconds.
Host reset: Remove it from the host and the device is factory reset.
Note: This should only be used in the event your network’s primary controller
is missing or otherwise inoperable
Parameter Settings
-
ADD/REMOVE
–Manual add mode: Press the button 3 times.
–Auto-add mode: LED will blink within 30 seconds after first power on
Tap x1: control on/off
Tap x2: scene 1 -
Factory reset:
Manual: Click the button 2 times quickly, and hold for at least 10 seconds Host reset: Remove it from the host and the device is factory reset. -
Association(Support 2 group, each group max support 5 devices)
Group 1 lifeline
Group 2 send a basic set -
LED indicator (quickly press 6x: change Parameter)
(LED flashes 2 times when the configuration parameter changes.)
Parameter=1, Size=1,
Value=0(Default) Load On, Indicator LED On
Value=1 Load On, Indicator LED Off
Value=2 LED always Off -
Auto Turn-OFF Timer
(LED flashes 2 times when the configuration parameter changed.)
Parameter =2, Size=4, Values: 0 – 65535 (Min); Defualt =0 turn off outlet -
Auto Turn-ON Timer
(LED flashes 2 times when the configuration parameter changed.)
Parameter =4, Size=4, Values: 0 – 65535 (Min); Defualt =0 turn on outlet -
Restores state after power failure(quickly press 10x: change Parameter)
(LED flashes 2 times when the configuration parameter changed.)
Parameter=6, Size=1, Value=0 Output off
Value=1 Output on
Value = 2 Restores state after power failure(Default) -
Scene function
scene 1: Tap 2x
FCC / IC
This device complies with part 15 of the FCC and Industry Canada license-
exempt RSS standard(s). Operation is subjected to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the equipment.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
CAUTION – PLEASE READ!
This device (ZW36) is intended for installation in accordance with the
National Electric Code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in Canada. If
you are unsure or uncomfortable about performing this installation consult a
qualified electrician.
WARNING – SHOCK HAZARD
TURN OFF THE POWER to the circuit for the switch and lighting fixture at the
service panel (circuit breaker) prior to installation.
ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER
OFF to avoid personal injury and/or damage to the switch.
OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns
MEDICAL EQUIPMENT
Please DO NOT use this switch to control Medical or Life Support equipment.
Z-Wave devices should never be used to control the On/Off status of Medical
and/or Life Support equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Important note: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
CONTROLLING APPLIANCES
Please exercise EXTREME CAUTION when using Z-Wave devices to control appliances. The reason being is because the appliance you want to control may be in a separate room and if unintentional behavior occurs (such as a device turning on or off – either intentionally via schedules, or unintentionally via network error) this event may lead to a hazardous condition. For these reasons, please note the following suggestions:
- Do not include Z-Wave devices in Groups or Scenes if they control appliances.
- Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended, unintentional, or automatic power control
COMMAND CLASS
GENERIC DEVICE CLASS:
0x10 – GENERIC_TYPE_SWITCH_BINARY
SPECIFIC DEVICE CLASS:
0x01 – SPECIFIC_TYPE_POWER_SWITCH_BINARY
COMMANDCLASS:
0x5E – COMMAND_CLASS_ZWAVEPLUS_INFO
0x86 – COMMAND_CLASS_VERSION
0x72 – COMMAND_CLASS_MANUFACTURER_SPECIFIC
0x5A – COMMAND_CLASS_DEVICE_RESET_LOCALLY
0x85 – COMMAND_CLASS_ASSOCIATION
0x59 – COMMAND_CLASS_ASSOCIATION_GRP_INFO
0x73 – COMMAND_CLASS_POWERLEVEL
0x25 – COMMAND_CLASS_SWITCH_BINARY
0x27 – COMMAND_CLASS_SWITCH_ALL
0x70 – COMMAND_CLASS_CONFIGURATION
0x8E – COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
0x55 – COMMAND_CLASS_TRANSPORT_SERVICE
0x9F – COMMAND_CLASS_SECURITY_2
0x6C – COMMAND_CLASS_SUPERVISION
0x7A – COMMAND_CLASS_FIRMWARE_UPDATE_MD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>