EVA LOGIK WF31T 3 Way WiFi Toggle Dimmer Switch Installation Guide

EVA LOGIK WF31T 3 Way WiFi Toggle Dimmer Switch Installation Guide

Part 1. Installation

A Few Quick Reminders
A quick note before we give out the wiring schematics. Please do not try installing this device if you are unsure of how electrical circuits operate within your home. As exciting as it is to have a smart switch installed, it can be dangerous and even life-threatening if you do not install this correctly. Please consult a qualified electrician if necessary. With that said, here are a few other warnings we’d like to point out for your safety:

Air-Gap Switch:
Stay at right for normal use Shift to left for Bulb replacement

HOW TO INSTALL THE WIRES

1. Unscrew: carefully turn the screw counter clockwise to leave enough space for the wire to be inserted. Do not unscrew the screws completely.
2. Press down: Once loosened, use your finger so it catches the thread.
3. Insert the wire: make sure the wire is completely straight, then insert it into the terminal while holding down the screw. Do not wrap the wire around the screw!
4. Tighten: Turn the screw clockwise to tighten the wire. Make sure the wires are locked!
   Note: There are 2 holes for each terminal can be used in the connection. You can use a jump wire or the second hole at the terminal to connect.

Note before installation

1. The Wi-Fi In-wall Smart Switch must not exceed 150W LED, 500W incandescent.
2. The switch box required: 1-gang U.S. wall box. 3½ in deep recommended, 2¼ in deep minimum. The switch is designed only for use with permanently installed fixtures.
3. Work with regular 3-way on/off for 2 locations control. It can only be connected with regular 3-way on/off switch, don’t use a smart switch or a dimmer switch! Couldn’t work with an add-on switch!
4. The colors of your wires may not match the ones in our diagrams so please make sure you’ve identified all wires correctly based on their source, not color only.
5. Please check your original 3-way wiring circuit in your home before installation, and then follow the wiring diagram option 1 or 2 in the manual.
6. Install the smart switch in the switch box which directly connects to the power Line and Neutral.
7. This switch requires a Neutral for installation, or the installation will not succeed.
8. Not recommended for fan.
   If you have any questions, please contact us at ask@nie-tech.com

Part 2. Wiring Diagram

Part 3. Manual Control

1. Tap 1( Up button): turn on the light (the last brightness level) Press and hold (Up button): add brightness
2. Tap 1(Down button) : turn off the light Press and hold (“down” button) : reduce brightness.
3. Adding your device to Wi-Fi network: Please make sure the switch is on the “OFF” position. Hold the “down” button more than 10s until the bulb flashes and the “blue” LED blinks rapidly to initiate App-configured Mode.
4. If you need to reset the device ( Factory setting) Network reset 1.Turn off the light(when the light is on) 2.Hold the “down” button until the light bulb flashes ( the blue LED blinks rapidly)

Part 4. APP Connection

1. Please scan the QR code to download the application “Smart Life”.
2. If you cannot download Smart Life app, please search “Smart Life” on Google Play (for Android phone) or Apple Store (for iOS phone) to download. After you download the Smart Life App and register a new account, please follow the instructions below to set up your smart switch.
3. The smart switch can be also used with Amazon Echo and Google Home. Please scan the QR code below and follow the instructions if you have any trouble pairing with them.

https://e.tuya.com/smartlife

https://nie-tech.com/wp-content/uploads/2018/12/Quick-Guide-of- Using-Amazon-Echo-To-Control-Smart-Devices-V1.02.pdfhttps://nie-tech.com/wp- content/uploads/2018/12/Quick-Guide-of-Using-Google-Home-to-Control-Smart- Devices.pdf

Please Note:

• Our products only support 2.4GHz Wi-Fi network.
• 3 connection network modes: Bluetooth quick-fit Mode, Easy Mode, AP Mode. Choose the most suitable mode to configure the network.
• Please operate quickly when “BLUE” LED indicator blinks rapidly.
• When indicator flash enters the network, complete standard operation within 30s
• “PURPLE” LED Flashing slowly enters AP Mode (select “AP Mode” follow the below instructions.)
• Make sure the switch works properly by manual control before network configuration.
• Device Reset / Network reset step 1: turn off the light (when the light is on) step 2: hold the “Down” button until the light bulb flashes (” BLUE”LED blinks rapidly)

Bluetooth quick-fit Mode:

(1) Turn on your Phone bluetooth.

(2)
The auto-connection comes with “BLUE”LED indicator blinks for 3 minutes to wait for configuration. If it stopped, please Hold the “down” button more than 10s until the bulb flashes and the blue LED blinks again.

Easy Mode:

AP mode:

If you cannot configure it by the default mode successfully, try to connect by AP mode.

1. When the blue LED indicator flashes quickly, press and hold the down button for more than 5s until the bulb flashes twice to enter the AP mode, and the purple LED indicator flashes quickly.
2. Click on “is slowly blinking(2s/time)” in the upper right corner.
3. Click “Confirm light flashes.”
4. Enter Wi-Fi network password.
5. Open wireless LAN settings with “Smart Life-xxxx/ SL-xxxx”.
6. Back in the application, continue adding devices and wait for the connection to complete. — AP Network Configuration Mode to Easy Mode: When the purple LED indicator flashes quickly, press and hold the “down” button for more than 5s until the bulb flashes 1 time to enter easy mode, and the blue LED indicator flashes quickly.

Part 5. Network Configuration

OPERATION GUIDE

• Adding your device to Wi-Fi network: Please make sure the switch is on the “OFF” position.
  Hold the “down” button more than 10s until the bulb flashes and “blue” LED indicator blinks rapidly to initiate App-configured Mode.

• If you need to reset the device ( Factory setting) Network reset
  1.Turn off the light(when the light is on)
  2.Hold the “down” button more than 10s until the bulb flashes (“blue” LED indicator blinks rapidly)

Part 6. Parameter Settings

The LED indicator flashes 3 times after each parameter setting successfully.)

· LED Indicator Status Setting (This parameter can access you to choose the led indicator to be on when the switch (light) is on/off, or LED indicator remains on/off all times.)
Value=1 (default) LED is On when the switch (light) Off and LED is Off when the switch (light) On.
Value=2 LED is On when switch (light) On and LED is Off when the switch (light) Off.
Value=3 LED is always Off.
Value=4 LED is always On.

Operation: Quickly press “down” button 5 times.
Please note: the switching of each value is in order, a quick press “”down” button 5 times will switch once. eg: Switching from value1 to value 4 needs 3 switching’s.

· Restores State after Power Failure (This parameter can access you to set the switch to be on/off after power failure.)
Value=1 The switch is off regardless of the state prior to power failure.
Value=2 The switch is on regardless of the state prior to power failure
Value=3(default) Memory state before power failure This switch will be return to state prior to the power failure after power is restored.
Operation: Quickly press “up” button 5 times. Please note: the switching of each value is in order, a quick press “up” button 5 times will switch once. eg: Switching from value1 to value 3 needs 2 switching’s.
· Light off State Setting (This parameter can access you to set the light fade out or off immediately.)
Value=1 (default) Fade out
Value=2 Instantaneous off
Operation: Quickly press “up” button 8 times
Please note: the switching of each value is in order, a quick press “up” button 8 times will switch once. eg: Switching from value1 to value 2 needs 1 switching.

· Button Function Setting (This parameter can access you to set the “up” button to turn the light on/off.)
Value=1 (default) The “up” button turn the light on and “down” button turn lights off.
Value=2 The “up” button turn the light off and “down” button turn lights on.
Operation: Quickly press “down” button 8 times
Please note: the switching of each value is in order, a quick press “down” button 8 times will switch once. eg: Switching from value1 to value 2 needs 1 switching.

FCC
This device complies with part 15 of the FCC and Industry Canada license- exempt RSS standard(s). Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equip- mint. Such modifications could void the user’s authority to
operate the equipment.-TV operate the equipment.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

CAUTION – PLEASE READ!
This device (WF31T) is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician.

WARNING – SHOCK HAZARD
TURN OFF THE POWER to the circuit for the switch and lighting fixture at the service panel (circuit breaker) prior to installation.
ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER OFF to avoid personal injury and/or damage to the switch.

OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns V4.0

www.nie-tech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>