ION 8541725685 Surf FM Floating Waterproof Stereo Boombox User Guide

ION 8541725685 Surf FM Floating Waterproof Stereo Boombox

Safety & Warranty Information

1. Read these instructions. Keep these instructions. Heed all warnings. Follow all Instructions.
2. Do not defeat the safety purpose of the polarized or grounding-type plug (if applicable). A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
3. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
4. Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus (if applicable). When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
5. Unplug this apparatus during lightning storms.
6. Power Sources (if applicable): This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit.
7. Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries (a battery pack or an installed battery) shall not be exposed to excessive heat such as sunshine, fire, etc. (This applies only if your product uses a battery.)
8. Protective earthing terminal (if applicable): The apparatus should be connected to a mains socket outlet with a protective earthing connection.
9. For Class II apparatus only (if applicable): This symbol means the equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.
10. Class II Wiring (if applicable): To reduce the risk of electric shock, the external wiring connected to the terminals with “Class II Wiring” requires Class II wiring installed by an instructed person or the use of ready-made leads or cords.
11. This apparatus is for professional use only. Intended operational climate: moderate.
12. (If applicable) When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Be careful not to damage the power cord. Before using it again, make sure the power cord has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer.
13. Warning (if applicable): Excessive sound pressure (high volumes) from headphones can cause hearing loss.
14. Warning (if applicable): Please refer to any important information (e.g., electrical, safety, etc.) printed on the exterior bottom enclosure or rear panel before installing or operating the product.
15. Warning (if applicable): Terminals marked with the lightning bolt symbol may be of sufficient magnitude to constitute a risk of electric shock.

Safety Notices

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un- insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

INSTRUCTIONS: The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this appliance.
WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture.
Electrical equipment should NEVER be kept or stored in damp environments.

NOTICE CONCERNING FCC REGULATIONS:

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (a) reorient or relocate the receiving antenna; (b) move this unit; (c) increase the separation between the equipment and receiver; (d) connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (e) be sure that all cables are properly shielded, using a choke or ferrite where appropriate; (f) consult the dealer or an experienced radio/television technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

If apparatus contains a coin/button-cell battery:
Warning:

• Do not ingest the battery—chemical burn hazard.
• The remote control supplied with this product contains a coin/button-cell battery.
• If the coin/button-cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• Keep new and used batteries away from children.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Disposal of Batteries (if applicable):

• Never dispose of any types of batteries in fire or near excessive heat or direct sunlight. Overheated batteries can rupture or explode.

• If you are unsure of how or where to dispose of a battery, refer to your local ordinances for the proper location, method, etc.

• Alkaline batteries & lithium button cell batteries: You can safely dispose of alkaline and lithium button cell batteries with normal household waste. They do not pose a health or environmental risk during normal use or disposal. (Alkaline batteries are composed primarily of common metals like steel, zinc, and manganese.)
  Do not dispose of large amounts of alkaline or lithium button cell batteries in a group. Used batteries are often not completely “dead.” Grouping them together can bring these “live” batteries into contact with one another, creating safety risks. To avoid this, insulate each battery with tape or other non-conductive material to ensure it does not discharge. Proven cost-effective and environmentally safe recycling processes are not yet universally available for alkaline and lithium button cell batteries. Some communities offer recycling or collection of these batteries. For more information, refer to your local ordinances or contact your local government.

• Lead-acid batteries: Dispose of lead-acid batteries by bringing them to an electronic waste center or recycling center, or dispose of them in accordance with your local ordinances. (Rechargeable lead-acid batteries are the same type used in automobiles and should be disposed of in a similar fashion.)

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Box Contents

• Surf FM
• Micro-USB Charging Cable
• Quickstart Guide/Safety & Warranty Information

Important Notes:

• Surf FM is IP67 waterproof, submersible up to 3 ft. (1 m) for 30 minutes, and dust-/dirt-/sand-proof.
• If the speaker fills with water, the sound will be muffled until the water has drained from the speaker.
• If Surf FM is exposed to saltwater, we recommend that you rinse it with tap water to maintain long-term performance of your product.
• Reposition Surf FM in the upright position for the best sound experience. Surf FM will continue to float in the position that it was placed or tossed into the water (e.g., if placed on its side, Surf FM will continue to float on its side).

Features

Rear Panel

1. Auxiliary Input: Open the bottom cover to access the Aux input. This stereo 3.5 mm (1/8”) input can be used to connect a CD player, MP3 player, or other audio source.
   Note: Bluetooth sources and the Aux input cannot be used at the same time.

2. Micro USB Port: Open the bottom cover to access the USB port. Use the included USB cable to connect this to a USB port on your computer or phone charger to recharge Surf FM’s battery.
   Note: When the bottom cover is open, the unit will not be water resistant. Make sure Surf FM and connections are dry before charging. Never charge when the unit is wet.

Bottom Panel
Tripod Mount: Attach a tripod to this 1/4” (6.35 mm) threaded mount.

Front Panel

1. Bluetooth Button/FM Mode: Press and hold this button to disconnect a paired Bluetooth device. Press this button to enter FM mode.

2. Bluetooth LED: This blinks when Bluetooth pairing or illuminates solid when connected to a Bluetooth device.

3. Call Receive / Call End / Play / Pause: Press to play or pause a track from a connected Bluetooth device. Press and hold this button for 2 seconds to enable your connected smartphone’s voice assistant (e.g. Siri®, Google®, etc), and then speak into the microphone. When Bluetooth-paired, press and release this button to answer a phone call. The phone’s ringtone will be heard through Surf FM’s speaker until the call is answered. When the call has been disconnected, Surf FM will resume playing music. To reject an incoming call, press and hold this button.

4. Power On/Off Switch: Press and hold this button to turn Surf FM on/off. While Surf FM is connected to a power source, it does not need to be powered on to charge the battery. Note: Surf FM will power off after 15 minutes if there is a Bluetooth connection but no audio signal is being received.

5. FM LED/Charging Indicator: The red LED will slowly blink when the battery needs charging. The LED is solid red when the battery is charging. When the power is on and the battery is fully charged, the red LED will be off. The LED is solid green when in FM mode.

6. Volume Up: Press this to increase the speaker volume on Surf FM.

7. Volume Down: Press this to decrease the speaker volume on Surf FM.
   Note: Double tap the Power button to enable or disable voice prompts.

8. Next Track: Press and release this button to skip to the next Bluetooth track.

9. Previous Track: Press and release this button once to go to the beginning of the track. Note: With some apps, pressing the Previous Track button or Next Track button may go to another playlist or music genre.

10. Microphone: Talk into this after receiving a call.

Technical Specifications

• Output Power: 26 W (peak)
• Frequency Response: 70 Hz – 18 kHz
• Bluetooth:
  • Profile: A2DP, HFP, AVRCP
  • Module: Bluetooth 5.0
  • Range: Up to 82 ft. (25 m) *
• Bluetooth range is affected by walls, obstructions, and movement. For optimal performance, place the product in the center of the room so it is unobstructed by walls, furniture, etc.
• Water Resistance Class: IP67
• Battery :
  • Battery Life: Up to 20 hours
  • Recharge Time: Up to 4 hours
• Aux Input: 3.5 mm (1/8”) line-level
• USB Charging Port: +5 V, 2 A
• Dimensions (WxDxH): 10.3” x 5.9” x 6.4” / 262 x 150 x 163 mm
• Weight: 2 lbs. / 0.9 kg

Trademarks & Licenses

ION Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by ION Audio is under license. All other product names, company names, trademarks, or trade names are those of their respective owners.

Support

IMPORTANT: For the full User Guide, visit ionaudio.com.
For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit ionaudio.com.
For additional product support, visit ionaudio.com/support.

Operation

Pairing or Disconnecting a Bluetooth Device

1. Turn on your Bluetooth device.

2. Power on Surf FM and it will automatically go into pairing mode to search for Bluetooth devices. You will know you are in pairing mode when the Bluetooth icon is slowly flashing.

3. Navigate to your Bluetooth device’s setup screen, find “Surf FM” and connect.
   Note: If your Bluetooth device prompts for a pairing code, enter “0000”.

4. Press and hold the Bluetooth button to disconnect a paired Bluetooth device.

5. To connect to another Bluetooth device, repeat step 3.
   Note: Maximum range will be achieved when using devices with Bluetooth 5.0.

Stereo-Link™: Linking Two Speakers Together Wirelessly

1. Power on both Surf FMs.
   Note: In order to use Stereo-Link Mode, you cannot have a Bluetooth device connected. If one speaker is connected to a Bluetooth device, break the connection by pressing and holding the Bluetooth/FM button.

2. With no Bluetooth device connected (blue LEDs on both speakers will blink), on one Surf FM double-press the Bluetooth/FM button until you hear a short 3-tone melody; repeat this for the second Surf FM. The melody will indicate the Surf FMs are searching for each other to link as their blue LEDs begin to blink fast.

3. Wait about 10-30 seconds for the Surf FMs to find each other. Once “linked”, one Surf FM will say “Paired” (if the voice prompts are enabled). Now that the two speakers are “linked,” one speaker’s blue LED will be solid, while the other speaker’s blue LED will blink slowly to indicate it’s ready to pair the stereo-linked speakers to your Bluetooth device (e.g., your phone).

4. When the Surf FMs are wirelessly linked to play in stereo, on your Bluetooth device turn on Bluetooth, and connect to “SURF FM”.

5. Once your smartphone is paired, you will hear “Paired” (if the voice prompts are enabled) and audio can now play out of both speakers in stereo.
   • In Stereo-Link Mode: UI Controls on both speakers will be active.
   • To exit Stereo-Link Mode, double-press the Bluetooth/FM button until the speaker goes back into pairing mode saying “Ready to Pair”.
   • In Stereo-Link Mode, press Power to turn off both speakers.

Note: If a Surf FM is in Stereo-Link Mode when you power it off, when you power it back on, it will revert back to single mode, and be ready to pair to a Bluetooth device if it does not find another Surf FM to link to within 15 seconds. To re-enter Stereo-Link Mode, follow Steps 1 – 5 above.

Using the Phone

Note: You must power on and pair Surf FM with your Bluetooth device before using it to listen to music or as a speakerphone.
When you have an incoming call, Surf FM’s speaker will play a ringtone.

1. To answer the call, press Surf FM’s Call Receive/End button.
   Note: If you get an incoming call during music playback, the music will pause until you end the call.

2. Speak into the microphone and adjust the call volume using the – and + buttons.

3. To end the call, press the Call Receive/End button.

4. To reject an incoming call, press and hold the Call Receive/End button.

Selecting a Radio Station:

1. Press the Bluetooth/FM button.
2. Select a radio station using the </> buttons.

Saving a Preset:

1. Press the Bluetooth/FM button to choose FM Radio. The FM LED will illuminate solid green.
2. Press and release the </> buttons to select a FM radio station that you want to save as a preset. A voice prompt will be heard identifying the selected station.
3. Press and hold the Bluetooth/FM button for 3 seconds to enter Preset Creation mode.
4. Press and release the </> buttons to select from one of the 6 preset locations. For each button press of < or >, the unit will say the active preset number (for example, “two”). Once the desired save location is reached, press and release the Bluetooth/FM button to save the station preset. The FM LED will show 4 quick green flashes to confirm a preset is saved and then exit Preset Save mode and return to FM mode.

Selecting a Preset:
To select from the 6 Preset stations, press and release Play/Pause in FM radio mode. The tuner will jump to the next preset location and say the name of the preset location (for example, “three”), and resume playing the FM station audio.
Note: When audio tones are playing, the FM signal will be temporarily muted.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>