hansgrohe Rebris S 80 Washbasin Mixers Instruction Manual
- June 10, 2024
- hansgrohe
Table of Contents
- hansgrohe Rebris S 80 Washbasin Mixers
- MODELS
- Product Product Information
- Technical Specifications
- Product Installation Instructions
- Assembly Instructions
- Product Usage Instructions
- Instructions for use
- Cleaning
- Service and Support
- Safety Notes
- Installation Instructions
- Technical Data
- Symbol Description
- Dimensions
- Flow diagram
- Spare parts
- Special accessories
- Operation
- Test certificate
- Hansgrohe
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe Rebris S 80 Washbasin Mixers
MODELS
- Rebris S 80
- 72510000
- 72540XXX
- Rebris S 80 CoolStart
- 72513XXX
- 72514000
- 72584XXX
- Rebris S 80 CoolStart EcoSmart
- 72586XXX
- Rebris S 110
- 72517XXX
- 72541XXX
- Rebris S 110 CoolStart
- 72519XXX
- 72520XXX
- 72527XXX
- Rebris S 110 CoolStart EcoSmart
- 72588XXX ****
- Rebris S
- 72210XXX
- 72212XXX
- Rebris E 80
- 72543XXX
- 72550000
- Rebris E 80 CoolStart
- 72553XXX
- 72554XXX
- 72585XXX
- Rebris E 80 CoolStart EcoSmart
- 72587XXX
- Rebris E 110
- 72544XXX
- 72557XXX
- Rebris E 110 CoolStart
- 72559XXX
- 72560XXX
- 72551XXX
- Rebris E 110 CoolStart EcoSmart
- 72589XXX
- Rebris E
- 72211XXX
- 72213XXX
Product Product Information
Rebris Shower System
The Rebris Shower System is designed to provide a comfortable and relaxing shower experience. It is available in different models including Rebris S 80, Rebris S 110, Rebris E 80, and Rebris E 110. These models come with different features including CoolStart and EcoSmart technology.
Technical Specifications
- Operating Pressure: max. 1 MPa
- Recommended Operating Pressure: 0.1 – 0.5 MPa
- Test Pressure: 1.6 MPa
- Hot Water Temperature: Flow Limiter
Product Installation Instructions
Gloves should be worn during installation to prevent crushing and cutting injuries. The product may only be used for bathing, hygienic and body cleaning purposes. The hot and cold supplies must be of equal pressures.
Montage (German)
Follow the instructions provided in the manual to install the Rebris Shower System.
Assembly Instructions
Follow the instructions provided in the manual to assemble the Rebris Shower System.
Product Usage Instructions
The Rebris Shower System is exclusively designed for drinking water. It is recommended that you do not use silicone containing acetic acid. To adjust the hot water limiter, refer to the instructions provided on page 35 of the manual. Using a hot water limiter in combination with a continuous flow water heater is not recommended.
Betrieb
Refer to the operating instructions provided in the manual to use the Rebris Shower System.
Instructions for use
Refer to the operating instructions provided in the manual to use the Rebris Shower System.
Cleaning
To clean the Rebris Shower System, refer to the cleaning instructions provided on page 38 of the manual.
Service and Support
If you require any assistance with the Rebris Shower System, refer to the service and support instructions provided on page 39 of the manual. You can also contact our customer support team for further assistance.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The product may only be used for bathing, hygienic and body cleaning purposes.
- The hot and cold supplies must be of equal pressures.
Installation Instructions
- Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
- The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
- The plumbing codes applicable in the respective countries must be observed.
- The drain valve must only be used as intended. It is not allowed to attach other objects to the drain valve, for example a semi-pedestal.
- If the instantaneous water heater causes problems or if you wish to increase the water flow, the EcoSmart® (flow limiter) located behind the aerator can be removed.
Technical Data
This mixer series-produced with EcoSmart® (flow limiter)
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5 MPa
- Test pressure: 1,6 MPa
- (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 60°C
- Thermal disinfection: 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol Description
Do not use silicone-containing acetic acid!
Adjustment
- To adjust the hot water limiter. Using a hot water limiter in combination with a continuous-flow water heater is not recommended.
Dimensions
Flow diagram
Spare parts
- XXX = Colors
- 000 = Chrome Plated
- 670 = Matt Black
Special accessories
(order as an extra)
- special tool #58085000
- Installation putty
- seal #98996000
- Cleaning
- Cleaning recommendation
- Warranty
- Contact
- www.hansgrohe.com/cleaning-recommendation
Operation
- Hansgrohe recommends not to use as drinking water the first half liter of water drawn in the morning or after a prolonged period of non-use.
- After periods of prolonged non-use, but at least every third day, the fittings must be opened with the handle in hot and cold position to prevent stagnation in the connecting lines. Let the water run until the water temperature is constant.
Test certificate
Hansgrohe
- Auestraße 5 – 9 · D-77761 Schiltach
- Telefon +49 (0) 78 36/51-1282
- Telefax +49 (0) 7836/511440
- E-Mail: info@hansgrohe.com
- Internet: www.hansgrohe.com
07/2022
9.08501.01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>