HOLLYLAND Mars 400S Pro SDI/HDMI Wireless Video Transmission System User Manual

: June 6, 2024
: HOLLYLAND

HOLLYLAND Mars 400S Pro SDI/HDMI Wireless Video Transmission System

FOREWORD

Thank you for purchasing Hollyland Mars 400S PRO Wireless HD Video Transmission system. Please kindly read this manual carefully before using it. Hope you have a pleasant experience.

KEY FEATURES

400ft Transmission Range between TX and RX(LOS)
300ft Transmission Range between TX and APP(LOS
Integrated Cold Shoe for Quick Installation
Lowest Transmission Latency 0.08s
SDI Input & HDMI Input at TX
SDI Output & HDMI Output at RX
Supports DC Power Supply, USB Type-C Power Supply and Battery Power Supply
1 Transmitter Supports 2 Receivers(1 Transmitter Supports 1 Receiver and 2 APPs Monitoring, or 1 Transmitter Supports up to 4 APPs Monitoring Without Receiver)
Supports Smart Channel Selectio
Supports APP Firmware Upgrade
Direct Data Stream from RX for Live Streaming

PACKING LIST

1 TX WITH 1 RX PACKING

Transmitter x1
Receiver x1
Antenna x5
DC Adapter x1
User Guide x1

SINGLE RECEIVER PACKING

Receiver x1
Antenna x3
DC Adapter x1
User Guide x1

TYPICAL SETUP

1 TX-1 RX SETUP

PRODUCT INTERFACES

A TRANSMITTER

Antenna Interface
Fan Air Outlet
SDI Input
OLED Display Screen
UP
OK
DOWN
Cold Shoe
USB Type-C Interface
Power Switch
HDMI Input
DC Input

B RECEIVER

Antenna Interface
Fan Air Outlet
SDI Output
OLED Display Screen
UP
OK
DOWN
Cold Shoe
USB Type-C Interface
Power Switch
HDMI Output
DC Input

INSTALLATION

Install the antennas as demonstrated.
Secure the cold shoe with 1/4 screw hole at the bottom of the transmitter and mount it to the camera.
Connect the HDMI input or SDI input of the transmitter with camera’s by HDMI or SDI cable.
Connect to a power supply(compatible with NP-970 battery or the same series of the batteries).
Turn on the devices.

OLED DISPLAY

A TRANSMITTER

Device Number
WIFI Signal Strength
Scene Mode
USB Flash Detection Indicator
Device ID
Channel Display
Video Format
Fan Status
Battery Voltage Display

B RECEIVER

Device Number
WIFI Signal Strength
Scene Mode
USB Flash Detection Indicator
Device ID
Chanel Display
Video Format
Fan Status
Battery Voltage Display

OLED DISPLAY

CAUTION

This device supports several power methods, and the device will be charged by the method which has a higher voltage.

The picture on the left shows the symbol of Type-C power supply, the picture on the right shows the symbol of DC power supply.

QUICK GUIDE

Long press the “OK” button for 3 seconds to enter the root menu interface. Click “UP” and “DOWN” button to switch menu options, click “OK” to confirm.

CHANNEL CHANGE

Press the button ” UP/DOWN” on the transmitter or the receiver to change the current channel. Press “OK” to confirm the channel number, then the channel of the receiver and the transmitter will be synchronously and automatically changed.

PULL STREAM FROM RECEIVER

Confirm there is video format display on both transmitter and receiver. Use the TypeC to Lan Connector to connect the laptop and RX.
Go to the network settings onthe laptop and set it to DHCP mode.
Go to your live stream software, such as VLC Player, OBS Studio, Vmix, etc., and open the network video source via the RTSP URL: rtsp://192.168.218.25:5554.

QUICK GUIDE

APP DOWNLOAD AND CONNECTION

“HollyView” APP Download
Connecting Method:
Enter the WiFi connection interface of mobile phone and find out the WiFi named as “HLD + DEVICE ID”, and input the WiFi password to connect (Factory Defult Password is: 12345678). After successful connection, you can have the APP monitoring.

PRODUCT PARAMETERS

| Transmitter| Receiver
---|---|---
Interfaces| HDMI Input(Type A Female)
SDI Input
2 Antenna Interfaces (RP-SMA Male) DC Input
USB Type-C| HDMI Output(Type A Female)
SDI Output
2 Antenna Interfaces (RP-SMA Male) DC Input
USB Type-C
Supply Interfaces| DC Power Input:6-16V

USB Type-C Power Supply:5V/2A Battery Power Supply:6-16V DC

| DC Power Input:6-16V

USB Type-C Power Supply:5V/2A Battery Power Supply:6-16V DC