XPOWER XP-DQ110-WH Double Spray Humidifier User Manual
- June 6, 2024
- XPOWER
Table of Contents
XPOWER XP-DQ110-WH Double Spray Humidifier User Manual
Please read the instructions carefully before using the product to ensure the product is used correctly
- Please use mineral water or unfiltered tap water. It is not recommended to use distilled water or purified water to avoid insufficient atomization and cause water droplets in the spray port.
- When using for the first time, the cotton core inside the main unit needs to fully absorb water (about 3-5 minutes).
- Do not touch the metal atomizer with your hands or hard objects to avoid damage.
- Do not use the humidifier upside down to prevent the residual water from the cotton swab leaking into the interior.
Packing Content
Specifications
Input: DC5V/1A
Rate power: 3W
Mist Volume: 50-80ml/h
Tank capacity: 400ml
Timing: 4hours / 6hours(interval spray)
Dimension: H190 x W77 x D77 (mm)
Weight: 190g
How to use
Spray Function:
Connect the power supply, wait until the cotton swabs fully absorb water.
Short press to open continuous spray mode, 2nd press to switch to interval
spray mode, 3rd press to turn off.
Night Light Function:
Long press to turn on/off the warm soft night light.
Automatic switch off function:
Automatically switch off after 4 hours in continuous spray mode; automatically
switch off after 6 hours in interval spray mode.
Precautions and troubleshooting
Please use mineral water or clean tap water for the humidifier. Distilled water or purified water is not recommended to prevent the residual water droplets from the spray port from affecting the spray.
It is better to fill the water container with up to 90% water.
Remember not to fill hot water.
Do not touch the metal atomizer on the top of the product with your hands or hard objects to avoid damage.
Not spraying or a small spray volume can be caused by the insufficient water absorption by the absorbent cotton swab/ insufficient water/ insufficient power.
The smell of the spray can be caused by the deterioration of the water. Please replace the water or spare cotton swabs.
Attentions:
- Please do not vigorously extrude or collide.
- Please do not dismantle or put it into fire or water when the product is power on to avoid shot circuit or leakage or corrosive environment, to avoid damage to the circuit leakage card, bankcard etc,) on the charger to avoid to cause
- Please do not use it in severly high temperature, high humidity.
- Please do not put the magnetic strip or chip card on the charger, otherwise ID magnetic card will lose efficacy.
- Please do not put the metal (Such as coin etc.) on the charger when charging, to avoid damage from heating.
- Avoid crash, hit, scrap, throw and prevent any damage to the charger.
- You may use the dry cloth to clean the product but avoid to use with any chemical cleaning product.
- XPower purchases USD200 million 3rd party product liability insurance. Public and Products Liability Insurance provides you with funds to pay compensation to a third party arising from injury or damage if proved product damage form XPower product.
- If the weather or temperature is hot, the temperature of the XPower charger and the charging device may be higher than normal during charging. The temperature will be higher when put both devices together. Thus, it is better if putting the XPower power bank in the air circulation environment and should be avoided storing in the handbag, on or under the bed. etc.
- If you have any technical problem on our product, please feel free to contact our customer service department.
FCC and CE Radiation Norm
This equipment has tested and found to comply with the limits for Class B digital device pursuant to Part 15 of Federal Communications Commission (FCC) rules.
This equirment has tested and found to comply with the lints of the European Council Directive on the approximation of law of the member states relating to electromagnetic compatibility(89/336/EEC) according to EN 55022 Class B.
FCC and CE Compliance Statement
These limits are designed to reasonable protection against frequency
interference in residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed or used in accordance
with the instructions, may cause harmful interference to radio communication,
However, there is no guarantee that interference will not occur in television
reception, which can be determined by turning the equipment off and on. The
user is encouraged to try and correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna increase the
separation between the equipment and the receiver Connect the receiver is
connected to.
RoHS stands for Restriction of Hazardous Substances, and impacts the entire electronics industry and many electrical products as well. The original RoHS, also known as Directive 2002/95/EC, originated in the European Union in 2002 and restricts the use of six hazardous materials found in electrical and electronic products. All applicable products in the EU market since July 1. 2006 must pass RoHS compliance.
Directive 2011/65/EU was published in 2011 by the EU. which is known as RoHS- Recast or RoHS 2. RoHS 2 includes a CE-marking directive, with RoHS compliance now being required for CE marking of products. RoHS 2 also added Categories 8 and 9, and has additional compliance recordkeeping requirements.
CAUTION!
The Federal Communication Commission warns the user that changes or
modifications to the unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Disclaimer Statement
Thank you for your choice to purchase and use XPower products! Please read this user manual carefully before using the product, to ensure correct operation method. We strongly recommend you to make data backup before using this product so as to make sure your data are completely safe. As the equipment manufacturer, XPower do not afford any direct or indirect responsibility for documents and data lose caused by any factor. Manufacturers do not have the obligation to afford any compensation and data recovery. XPower do not make special promise to users and distributors, XPower do not afford any unexpected data lose, direct or indirect loss. If you start to use this product, that means you understand and accept this disclaimer!
Copyright Description
All XPower products and relative data’s belong to XPower International Trading Ltd. . XPower International Trading Ltd. have the right of produce and copyright, reproduction is prohibited. This user manual includes, but not limited to all information with copyright protection, without permission from XPower International Trading Ltd. , no one is allowed to clone, copy, excerpt, translation or use for other things.
This user manual does not have any form of warranty, position statement or other hint. If there is any direct or indirect data lose. economic loss or enterprise bankruptcy caused by this user manual or its product information mentioned, XPower International Trading Ltd. and its staff will not afford any responsibility for that. Besides, the product specification and information mentioned in this user manual are just for your reference, and contents will update at any time without further notice. XPower International Trading Ltd. will not take responsibility for any error or negligence in this user manual.
The product name mentioned in this user manual can be only used for identification, and this name may be part of the other company’s registered trademark or production rights. When below two situations happened, this product will not have XPower’s warrant and service.
- The product does not belong to XPower’s authorization of warranty, specification alteration and parts replacement.
- Product bar code is vague or lost. The user manual will update as the product specification or driver’s change. Please visit the XPower International Trading Ltd. official website to get the details: www.xpower.com.hk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>