XPOWER X-600 1-3 HP Air Mover with Daisy Chain Owner’s Manual

XPOWER X-600 1-3 HP Air Mover with Daisy Chain

Introduction
XPOWER Air Movers are ETLICETL Certified and multifunctional Air Movers with the most efficient engineering design.

Features

• Low amp draws with a rated volume of 2600 to 2980 on High.
• Super quiet motor and super lightweight.
• Easy camping handle
• Easy and quick to disassemble for thorough dlean ing and service.
• Power cord lengths are 20 for P models and 25 for X models.
• *Easy cord wrap on the handle.
• Safety screens on open vents.
• speed switch.
• Luggage handle and wheels for “H” series models.
• Carpet clamp for “C senes models.
• Timer and fiter forTF series models.
• 3 air-flow positions for H’ series models (0, 20″ Kickstand, 90).
• 4 air-flow positions for other models (0, 20° Kickstand, 45″, 90).
• Durable and rugged housing with 5 Years Waranty.

Operation / Instructions

XPOWERAir Movers are intended to move air and to dry floors, walls, furniture, etc. Durable and easy to operate with an effective balance of static pressure and airflow, the units are suitable for a variety of applications

1. XPOWER Air Movers are shipped ready to use. Prior to plugging the unit into the power source, inspect completely for any shipping damage.
2. Plug the electrical cord into a standard grounded outlet.
3. Carefully place the Air Mover unit on a stable, flat dry surface.
4. The unit is capable to be used at 4 different angles to direct air flow, except that the unit with a handle is at 3 different angles.
5. Tum the switch to the desired speed, while making sure the unit operates normally.
6. To reduce the risk of injury, close supervision is necessary when the unit is used near children. Do not allow children to play with the unit.

AIR MOVER STORAGE
Units without “H” ca  be stacked (up to 4) on their sides Units with H can be stacked (up to 3) on their sides.

NOTICE:

1. The stacking feature is not secure for transportation
2. Remove the filters before stacking.

Safety Instructions

1. To prevent electric shock, do not operate the unit in standing water. Never plug in or unplug the unit With wet hands or while standing in water.

2. To avoid risk of injury, do not direct airflow at face or any part of the body

3. WARING: To reduce the risk of fire or electric shock, do not use the Air Mover with any solid-state speed control device.

4. Use only with GFCI-protected receptacles. Please contact a qualified electrician for verification and/ or installation of a GFCI receptacle if necessary.

5. Do not operate any Air Mover with a damaged cord or plug. Discard the unit or return it to an authorized service facility for examination and/or repair.

6. If’s an automatically operated device. To reduce the risk of injury disconnect from the power supply before servicing.
   Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners, or similar coverings. Do not route the power cord under furniture or appliances. Arrange the power cord away from the traffic area and where it will not be tripped over.

7. Do not allow children to play with an Air Mover at any time.

8. Do not move or carry an Air Mover while unit is operating.

9. An electronic instruction manual can be obtained through the manufacturer’s website www.xpower.com.

Maintenance Instructions

1. To keep the Air Mover clean, use a damp cloth to wipe the surface of the housing.
2. Never clean the Air Mover with water,
3. When not in use, unplug and store the Air Mover in a dry indoor place out of reach of children.
4. Always disconnect the Air Mover from its power source before performing any maintenance or cleaning.
5. Clean the optional frilters as often as necessary to avoid loss of airflow.

Troubleshooting

For any problems not listed below, call your local distributor or contact our Service Department.

AJr!Maver no.t

running

| No power input| Plugin   ATr Mover. check clrcu1t b: reader
---|---|---
Switch was not l1urned on| Turn on switch
Air Mov, er- fan wheel lammed| Remove material Jammin| g fan wheel
lr111take or exhaust:s.t bloc!ked| Turn unit  off and allow to| , pool .
then| 1remave blockage1|
Alt   Mover

vfbmtes

| Accumulation of dirt on fan blades. I| Cleaning Air!Mover fain! blad es

Specifications

XPOWER LIMITED WARRANTY (USA)

XPOWER’s Limited Warranty covers the unit (excludes PoWER CORD AND FILTER) from defects in material and craftsmanship. ne warranty covers norma use Tor a term of one year from the ongna p, o one wrapping. on-contiguous states must pay tor round trip Trent. A purchase receipt must be provided.

Important!
This warranty does not cover or apply to defects due directly or indirectly to misuse, abuse, disassembling- the use of this product is not in compliance with the instructions and specifications for its use. Service For Warranty service and parts replacement (US users only), you must:

• Call 1-555-865-8868 Tor an RMA (Return-Merchandise-Authorization) number.
• Have original proof of purchase.
• Use the original undamaged packaging or an industrial certified packaging method.

End-user will be responsible to ship the unit (with RMA Number showing on the shipping label) to the XPOWER Service Department. XPOWER to inspect, assess and advise the repairs needed and the
applicable cos For users outside the Us, please contact XPOWER Distributor in your country or region for VWarranty service and parts replacement.

600 Series Parts List

Daisy Chain Specifications (For model X-600A/P-600A
XPOWER Air Mover Model X-600A/P-600A are daisy-chainable with a low 3.8 amp draw The 12-amp onboard circuit breaker will allow two (2) additional same units to run on one circuit at the same time.

Accessories

Luggage Handle & Wheels (for “H” models) XPOWER Air Mover “H Model comes with built-in extendable luggage handle and wheels for easy transportation and mobility. Carpet clamp (for “C” models) XPOWER Air Mover “CModel comes with a carpet clamp specifically for drying under the carpets.

Filters (for “F” models)
A set of filters is available for the XPOWER Air Mover which will help prevent small debris and dust from entering the Air Mover. To clean the fiters: remove filters from the unit and wash with warm soapy water, rinse with lean water and let dry thoroughly before reinstalling.

Installation:
Filters snap into the air inlets.
Note: After I is for the Motor side, Filter II is for the Fan side.

Filter Removal:
Pul the filters out of the blower.
Note: After deaning make sure the filters are dry before installing

Warranty Registration (or US user only)

For your product warranty, please complete and mail /fax this fom to XPOWER MANUFACTURE, INC
Address: 668 S. 6th Ave., City of Industry, CA 91746, USA Tel: 1-856-8 55-8868 (For your convenience, register your product online at xpower.com)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>