wallas PI Thermo Control Panel Stoves 800 DSL, 85 DT/NDT, 88 DU User Guide

: October 27, 2023
: wallas

Table of Contents

wallas PI Thermo Control Panel Stoves 800 DSL, 85 DT/NDT, 88 DU
IGNITION
SUN SWITCH
HEATING WITH BLOWER LID
**PANEL LIGHTS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

wallas PI Thermo Control Panel Stoves 800 DSL, 85 DT/NDT, 88 DU

IGNITION

Press the Power Button for 3 seconds untilthe yellow power light will come on. Whenyou release the button, the yellow heatinglight will appear.
Red combustion light will light up when theburner flame has been ignited and thecombustion has stabilised (approx. in 5 min).Stove will be fully operational about 10 minlater.
Stove is set to always start in Manual Mode ready for cooking.

COOKING

In Manual Mode, turn the Temperature/ Power Knob to max. level 6 and begincooking. Adjust it to a lower temperature,if needed, as you would a domestic stove.
When Manual Mode for cooking is on, the orange Thermostat light is off.

HIGH ALTITUDE MODE

When the device is used 1500 m (4,900 ft) above sealevel, it is necessary to activate the High Altitude Modeto adjust the combustion.
Start the stove by holding the power button down for 10 seconds.
Yellow heating light will flash 3 times andthen change to a solid yellow light. HighAltitude Mode is now on and the stovehas started the ignition process.

SHUTDOWN

Press the Power Button down for 2seconds.
Yellow heating light will shut offimmediately.

Combustion indicator
Temperature / Power knob
Power button
Power indicator
Thermostat/blower lid indicator
Thermostat sensor
Heating indicator

SUN SWITCH

(IN PI THERMO MODE)

Sun Switch automatically turns the blower lidheater off if the temperature remains +3 C (37 F)above the set level for 1/2 hour due totemperature increase in weather.

Orange thermostat light willbegin to flash every 30 seconds.
Turn the Power Knob slightly toturn the Sun Switch off temporarily.
If heating is still needed, turnthe device back on manually.

Red combustion light will continue toflash for about 5 minutes, while thestove is cooling down. Heater cannotbe restarted until the cool down is completed.

HEATING WITH BLOWER LID

Once the stove is fully ignited, lower the blower lid downuntil it locks and the device will begin to blow warm airfor heating.
PI Thermo Mode: Set a target temperature (C°/F°) Manual Mode: Control heating power with knob
Rotate the Temperature/Power Knob to thedesired temperature (refer to temperaturechart on the first page) or heating power.
Switch between modes by turning the Temperature/Power Knob back andforth to min – max – min.

(STOVES WITH BLOWER LID)

To switch back to cooking, unlock the lid and pushit back to upward position. Make sure the stove isin Manual Mode before cooking.
Stove does not operate correctly if it is left in PI Thermo Mode.
When the PI Thermo Mode is chosen,the orange thermostat/ blower lid lightis on.

In Manual Mode, the light is off.

**PANEL LIGHTS

**

Heating on
Heating on in High Altitude Mode
Combustion has begun/is running
Cooldown/Flameout
Set temperature on heater is higher thancabin temperature – power is increasing
Set temperature on heater is lower thancabin temperature – power is decreasing
Sun Switch has shut down the device
Low voltage (usually about 15 secafter initiating start)
Overheat
Reminder indicating there was a faultafter fault code flashed for 5 min
Locked for security The device locks itself after two unsuccessful starts

Reach Out to a Professional for the Following:

All rights reserved. Wallas-Marin reserves the right to change or improve its products and to make changes in the content of this guide without obligation to notify any person or organizationof such changes or improvements. Go to www.wallas.com for current updates and supplemental information concerning the use of this product.

UNLOCKING

If the unit has locked itself,the combustion light and the heating indicator light will flash, signaling there has been failure that should be investigated and resolved prior to further use. Lights will flash for about 5 min.

While the lights are flashing, switch the main power off from the battery(Pull power plug, remove the use, open breakers, or in-line switch).
Wait for 5 sec. and switch the main power back on.
Press Heat Button (3) for more than 3 seconds to shut down the heater.
Restart the heater normally.

See the instructional video to unlock

PI THERMO CONTROL PANEL Stoves 800 DSL, 85 DT/NDT, 88 DU Please Refer to Manual for Full Operation and Maintenance Instructions at wallas.com